Search Documents

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By Huang Rui

The coal asphalt is combusted at different temperature in a heating cabinet with the temperature limit by 1200°C. By comparing the mass of the remainder of each experiment, the completely combusting temperature of asphalt smoke can be determined. Based on the experimental process of asphalt smoke, a discrete mathematical model of the asphalt smoke combustion is set by theoretic analysis. Through computer programming, the dynamic combustion process of asphalt smoke is calculated to simulate the experimental model. The result of experiment shows that coal asphalt can mostly react upon 500°C and the mass of remainder is 49.41% to initial mass of sample in the condition. The computing result shows that the temperature and the concentration of asphalt smoke influence its burning temperature approximating linearity. The consumed quantity of fuel to ignite the asphalt smoke needs be considered with the two factors.

Jan 1, 2006

By Frank R. A. Jorgensen

Flash smelting is used to smelt a large proportion of the world's copper and nickel and some lead/zinc concentrates. Understanding the factors controlling the ignition of these concentrates is an important consideration in designing burners and maximising the throughput of the flash smelting process. The literature on the subject is briefly reviewed and techniques for the measurement of ignition temperature discussed. The mineralogy of the concentrates and the role of thermodynamics and phase diagrams in interpreting and predicting ignition behaviour are emphasised and applied to interpreting results obtained on a nickel concentrate.

Jan 1, 2002

By Vinay Kumar, Jae-Chun Lee, Abhishek Kumar, Manis Kumar Jha

However, India is rich in ores and mineral, but E-waste recycling is necessary due to the report of national and international studies, which cautioned on the generation, treatment and accumulation of e-waste in India. Current data indicate that the total domestic e-waste generation including imports is around 382979 MT, however waste available for recycling and actually recycled are 144143 MT and 19000 MT, respectively. In which recycling by non-formal and formal sector are 95% and 5%, respectively. On the other hand, India has developed expertise in handling verities of metallic wastes in an organized and safe manner. The development of individual process or combined processes for handling the e-waste is underway. Eco- friendly and energy-saving processes are necessary to comply with stringent environmental regulations. The paper includes the recent trend of e-waste generation, recycling process and its future prospects particularly in India.

Jan 1, 2011

By Toru Taniguchi

In the Mitsubishi smelting furnace, copper concentrate, silica sand and water granulated slag from the converting furnace are injected through the process lances, together with oxygen enriched air, into the melt. Because bath smelting is used, the rates of particles/melt and gas/melt reactions are high enough and therefore tine grinding of the solid materials is' not necessary. Among these reactions, the dissolution rate of silica sand is the slowest and limits the overall reactions in the smelting furnace. Information on the dissolution rate of silica sand plays an important role for design of a new furnace. Theoretical calculations of the dissolution rate .of silica particles have been reported elsewhere. The authors conducted cold model experiments and could verify the calculation. In this paper, the dependence of dissolution rates of particles on the gas blowing rate, particle size and solid penetration depth in the bath is discussed.

Jan 1, 2002

By José García-Antón, Valentín Pérez-Herranz, José Luís Guiñón, Henry Reyes

"The majority of chromium electroplating operations employ Cr(VI)-based baths. During these processes, Cr(VI) is reduced to Cr(III). Besides Cr(III) other undesirable impurities are present such as iron, copper and nickel. The build-up of the impurities limits the lifetime of the plating solutions. Since the disposal of spent chromic acid baths is expensive and can cause significant environmental degradation, there is increasing interest in finding ways to regenerate waste chromium liquors.In this work, an electrolytic cell separated by microporous ceramic diaphragms was used to regenerate chromium plating solutions. The effect of the ceramic diaphragm structure parameters, such as porosity and pore size, on the performance indicators of the electrochemical reactor (fractional conversion, current efficiency, product yield, specific energy consumption) was investigated.The fractional conversion, the product yield and the current efficiency increased and the specific energy consumption decreased with the decrease in porosity.IntroductionChromic acid is widely used in industrial applications such as steel manufacture, metal finishing industries, aluminium anodising, pasivation of cadmium, magnesium, and zinc, etching of plastics and another industrial operations related with processing ferrous and no ferrous metals [1]. These processes employ baths with high concentrations in chromic acid, about 180 and 350 g/L, where hexavalent chromium is reduced to Cr(III):"

Jan 1, 2008

By T. Kamata, S. Takemoto, H. Takeuchi, M. Takayanagi, Y. Akahori, I. Jimbo

"A cooperative research work on the silver recycling process is underway between Matsuda Sangyo Co., Ltd. and Tokai University in Japan. Silver wastes treated here are mainly from photograph industries where the concentration of minor element is steadily increasing in the recent years. The waste materials are concentrated and the impurities are removed by evaporation and slagging. In this paper, the industrial practice of wastes treatment is introduced and the result of the laboratory studies on the removal of antimony and tin from the binary and ternary alloys will be discussed. Characteristics in the behavior of antimony and tin during the process are also discussed with the observation of practical operation.1. IntroductionPrecious metals such as gold and silver primarily come from mining practice and the byproduct in copper smelting. However, the recycled amount of these precious metals have been increased 1 along with the environmental restriction and the widely accepted idea of saving resources on the earth in the recent years.· Though the recycle process of precious metals are comparatively simple from other metals refining, the process has been getting more complicated as wastes treatment has to deal with more impurity elements which are intentionally added to the products. Among these additives, antimony is used in the film materials in the photography industries to suppress its inflammability. Tin is another concern ,that is also coming from photography wastes; These minor elements have become problematic during the recycle.The removal of these minor elements has been in operation at Matsuda through a traditional oxidation refinement process using a reverberatory furnace. However, the complexity of the charge makes the recycle process more tedious and troublesome. In order to investigate the minor element behavior in the complicated materials system during the silver recycling processes, a cooperative research work is undertaken between Matsuda Sangyo Co., Ltd. and Takai University in Japan. Silver wastes treated here are mainly discharged from photograph industries where the minor element contents such as antimony, tin and bismuth in those wastes are steadily increasing in the recent years. The liquid wastes containing silver are concentrated and then treated pyrometallurgically with solid wastes from other sources, where the impurities are removed ·by evaporation and slagging. The purpose of this study is to investigate detailed behavior of impurity elements in the silver. containing systems."

Jan 1, 2000

By J. C. Riani

The release of heavy metals into the environment is increasing among others due to human activities such paint and pigment industries, tanneries, and metal finishing industries. Among metal releases, chromium is notable because this metal is carcinogenic. Thus, the aim of this work is to use an ion exchange system composed of one cationic resin column and one anionic resin column in order to adsorb the chromium (III, VI) from chromium electroplating effluents with the objective of recycling the water. The methodology consists of chromium adsorption tests using the ion exchange resins system with Purolite the 850 (polystyrene matrix, functional group quaternary amine) and Purolite C 150 (polystyrene matrix, functional group sulfonic acid). The contaminated solutions were passed through the columns with the assistance of peristaltic pump. Samples of the outgoing solution were taken in order to control the conductivity and pH and analyze the metals. The effects of the feeding outflow on the chromium adsorption were evaluated. The results show that the quality of the water collected at the end of the process is within the Brazilian standards about the discarding of toxic substances in the environment (CONAMA 357/05). This makes possible the recycling of water into the process and also its discharge in the rivers.

Jan 1, 2006

By Thomas Gliick, Jianming Lu, David Dreisinger

"The Boleo project of Baja Mining (Vancouver) will process a mixed oxide-sulfide ore using an acid oxidation and reduction process in seawater to extract copper, zinc, cobalt and manganese. Copper will be extracted via SX-EW as copper cathode, zinc will be recovered as a zinc sulphate monohydrate crystal and cobalt will be produced as a cobalt cathode product after phosphinic acid extraction. Manganese may be recovered from the final solvent extraction raffinate by precipitation as manganese carbonate.The development of the cobalt recovery process (solvent extraction and electrowinning) will be discussed. The pilot plant solvent extraction circuit and subsequent bench and small pilot testing of cobalt electrowinning will be discussed. The Boleo project will produce approximately 1708 tonnes per armum of cobalt metal when fully commissioned.INTRODUCTIONThe Boleo property is held by the Mexican company, Minera y Metalllrgica del Boleo S.A. de C.V. (MMB). MMB is owned 70% by Baja Mining Corp. and 30% by a consortium of Korean companies consisting of KORES - Korea Resources Corporation, LS Nikko Copper, Hyundai Hysco, SK Networks and Iljin Copper. The project is fully financed and is now under construction with an expected startup in early 2013 .Average annual production, for the first six years for each of the metals is forecast as: 56,697 tonnes of copper cathode, 1,708 tonnes of cobalt cathode and 25,364 tonnes of zinc sulphate monohydrate. The project has an average life-of-mine cash cost (based on the three year trailing average metal prices, as of December 31, 2009, in accordance with SEC guidelines) of -$0.29/lb Cu, net of by-product credits for cobalt and zinc and with no credit for manganese production. There is the potential to produce up to 220,000 tonnes per armum of manganese carbonate (- 100,000 tpa contained Mn) via the relatively simple addition of a small number of unit operations to the proposed plant. The recovery of manganese metals from the manganese carbonate intermediate material is discussed in a separate paper in this proceeding."

Jan 1, 2012

By John A. S. Green, J. Gilbert Kaufman, Subodh K. Das

"The aluminum industry is a leading proponent of global sustainability and strongly advocates the use of recycled metal. As the North American primary aluminum industry continues to move offshore to other geographic areas, such as Iceland and the Middle East, where energy is more readily available at lower cost, the importance of the secondary (i.e., recycled metal) market in the U.S. will continue to increase. In the past, the recycling industry had been synonymous with the collection of aluminum beverage cans. However, as the opportunities for aluminum recycling have multiplied in motor vehicles, building and construction, and aerospace, these market are getting additional scrutiny for optimization of recycling strategies.Accordingly, the secondary industry can now draw upon a much wider range of product forms and alloys for its raw material, but this in turn brings issues of alloy sorting, impurity content, and control as the material is remelted and recycled into new product forms. The purpose of this paper is to take an integrated, industry-wide approach to look at the recovery of material from demolished buildings, shredded automobiles, and aging aircraft, as well as from traditional cans and other rigid containers. Attempts will be made to assess how the different alloys used in these separate markets can be recycled in the most energy efficient manner.IntroductionIn his recent book “Aluminum Recycling”[1], Mark Schlesinger points out that in traditional extractive metallurgy, the raw material used to produce a metal is mined from the earth and then is separated from other gangue minerals and impurities. In aluminum recycling, however, the ore body consists of scrap metal found on the ground, rather than in it. He further notes that scrap comes with its own variety of gangue and impurities such as painted coatings, other metal attachments, and even dirt and other contaminants. So, while the recycling process still requires some refinement and expenditure of energy, the effort and energy involved is much less than traditional mining."

Jan 1, 2008

By Dao Su, Kelang Mu, Yufeng Guo, Jinghua Zeng, Tao Jiang

"The influence of high pressure roller grinding (HPRG) on sintering of iron concentrate fines was investigated. Results of mini-sintering tests showed that assimilation temperature of iron concentrate fines decreased from 1230 ? to 1220 ? and assimilation time was shortened from 10 min to 5 min when the iron concentrate fines was pretreated by HPRG. Sinter pot tests showed that the yield of sinter increased from 60.33% to 72.92% , tumble index increased from 44.35% to 46.66%. The investigation indicated that, after being pretreated by HPRG, iron concentrate fines are improved in ballability and the fraction of fine particles increased, resulting in the improvement of granulation property and reactiveness in solid state reaction. As a result, sintering of iron concentrate fines were strengthened.IntroductionWith the rapid development of iron and steel industry and the decrease of high-grade ores, the imports of iron ore are increasing continually. It is of immensely strategic importance for development of iron and steel industry and energy security in our country to make good use of iron concentrate fine which is low price, high grade and has a refractory sintering property. When iron concentrate fine is used in sintering, granulation property of sinter mixture and permeability of sinter bed get poor. As a result, yield and quality of sinter fall down. Many researches show that, when HPRG is used in pelletization, quality of pellets is improved dramatically. Meanwhile, HPRG has a low energy consume, a large handing capacity and it is benefit for environment protect. At this theme, strengthening of sintering of iron concentrate fine pretreated by HPRG was investigated in this paper."

Jan 1, 2012

By Jeong-Soo, Joon Soo Kim, Rajesh Kumar, Sohn, Jin-Young Lee

"Liquid-liquid extraction (LLE) studies of tetravalent platinum from acidic chloride solutions have been carried out with Alamine 336 as an extractant diluted in kerosene. The title metal shows the inverse behavior at higher acid concentrations. Plot of log D vs. log [Acid], mol.L-1 gave a straight line with a negative slope of 0.8±0.03 indicating the exchange of one mole of hydrogen ions for every mole of platinum(IV) extracted into the organic phase. Extraction of platinum(IV) increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slope 1±0.3, indicating the association of one mole of extractant with the extracted metal species. The plot between metal distributions to aqueous to organic phases is 1.3±0.01; it indicates monomeric species was formed in organic phase. Stripping of metal from the loaded organic (LO) with mineral acids such as hydrochloric, sulphuric, nitric acids and bases like ammonia, hydrogen peroxide and sodium hydroxide are studied. The results indicated that hydrochloric acid and sodium hydroxide are the better stripping agents when compared with other acids and bases. Increase of temperature decreases the percentage extraction of metal indicating the process is endothermic. Regeneration and recycling capacity of Alamine 336 and extraction behavior of associated elements such as aluminium(III), magnesium(II), cobalt(II), iron(III) and nickel(II) were studied.IntroductionThe demand for platinum group metals (PGM’s) has risen in the last five years expected to keep in rising. Right now, the demand is already beyond the supply. The primary use of PGM’s today is in the automotive industry. Catalytic converters used in the PGM’s process to reduce greenhouse gases. Because of the current demand to reduce the green house effect the expected need for platinum is here stay. Country’s now advancing in the use of car production also are phasing increasing the needs for this metal. Chemical processing also use it, too. These industries account for more than 50% of all platinum production. Jewelry is other primary use of this precious metal whose value is much greater than gold. Other uses include computer data storage, scientific developments, fuel cell technology and in the glass manufacturing processes."

Jan 1, 2008

By Aline Maria dos Santos Teixeira, Francisco Manoel dos Santos Garrido, Joao Alves Sampaio, Marta Eloisa Medeiros

"Rocks for crops is a natural practice for soils fertilization which consists on adding rocks to the soil while water decomposes the rock, through chemical weathering, and gradually releases nutrients to the soil solution. This practice can be considered an alternative to the low production of potassium fertilizers in Brazil. In this context, the phonolite rock was characterized in order to evaluate its application as an alternative source of nutrients to the Brazilian agriculture. The phonolite studied is an igneous, volcanic rock with alkaline character that is chemically composed of a high grade of potassium due to the presence of feldspar minerals. In order to quantify the minerals present in the sample, characterization was carried out using several techniques such as X-ray diffraction, X-ray fluorescence and scanning electron microscopy.IntroductionBrazilian soils are generally acidic and nutrient poor due to the tropical climate in which high temperatures and intense rainfall favor a rapid decomposition of the rocks that from the soil. And as agriculture is one of the main bases of the country's economy, large amounts of fertilizer are used to make the soil productive.Although Brazil has large reserves of potassium, the demand for potash fertilizer is higher than the national supply, which makes the country dependent on fertilizer imports, especially in the form of potassium chloride. Thus, we must look for economic alternatives to traditional fertilizer [1].Stonemeal is a natural practice for soil fertilization that consists in adding basic or ultrabasic rocks to the soil so that water, through chemical weathering, decomposes the rock while it gradually releases nutrients."

Jan 1, 2011

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By Zhiqiang Han, Anil K. Sachdev, Baicheng Liu, Guomin Han, Alan A. Luo

The growth of precipitate phase ,B-Mg11Al12 in Mg-Al alloy is closely related to interface anisotropy and elastic interaction. The aim of this work is to investigate the effects of the interface anisotropy and elastic interaction on the morphology evolution and growth kinetics of the precipitate. In the work, the precipitation of ,B was studied using phase field modeling. In the model, the chemical free energy of the precipitate and the matrix were obtained via thermodynamic calculation. It is demonstrated that the interface anisotropy results in lath-shaped precipitate and the elastic interaction affects the shape of the end of the precipitate. The interface anisotropy causes uneven growth in different directions and the elastic interaction influences its preferential growth orientation. By combining the interface anisotropy and elastic interaction in the phase field modeling, the results showed that the precipitate phase has a lath-shape with lozenge ends, which is in agreement with experimental observations.

Jan 1, 2013

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

By S. Redik, C. Wenzl, D. Gregurek, A. Spanring

Zinc is a component of many input materials used in various pyrometallurgical processes, for example primary lead and zinc production from Pb/Zn ores and recycling processes dealing with zinc-containing residues (e.g., copper recycling, WAELZ process). Hence, zinc and its compounds are present in the respective metallurgical vessels and interact with the refractory lining. In the present work the zinc attack on the refractories out of various primary and secondary furnaces is briefly introduced and discussed. At the prevailing processing temperatures in the metallurgical vessels, zinc oxide is highly corrosive for the brick components. The knowledge of the wear behavior is based not only on a detailed chemical and mineralogical characterization carried out on provided post mortem samples, but also on FactSage calculations. This together with results obtained by practical testing in the RHI pilot plant represents an important prerequisite for product development and brick selection for the individual customer application.

Jan 1, 2016