Search Documents

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By Yves Fautrelle, Kader Zaidat, Hervé Combeau, Miha Zaloznik, Mohammed M'Hamdi, Bachir Saadi, Xiaodong Wang, Knut Omdal Tveito

"Numerical simulations of macrosegregation formation during horizontal solidification of a hypoeutectic Sn-Pb alloy in a rectangular cavity is presented and compared to experimental results. The experiment involves a melting phase, a holding stage at constant temperature with/without application of electromagnetic stirring, and finally solidification. We simulate all stages of the experiment and study the segregation of Pb throughout the experiment. A twophase volume averaged model is used for the numerical simulations, accounting for thermosolutal convection and assuming perfect microscopic mixing (lever rule). The influence of the melting phase and the electromagnetic stirring is studied with different cases to illustrate the consequences on the flow pattern and Pb segregation. The numerical simulations are compared to the experimental data and the impact of chemical inhomogeneities prior to solidification on macrosegregation formation is discussed.IntroductionMany extensive investigations have been performed so far on the solidification of metallic alloys. However, the melting process of metallic alloy has not attracted attention in a same manner. Nevertheless, melting of alloy may put forth peculiar effects as described in the present paper. It has been observed from a benchmark experiment [1, 2] that significant stratification might arise during the melting process of Sn-Pb alloy. That effect was put forth thanks to the analysis of the experimental temperature distribution which indicated that the convective fluid flow was almost zero. The effect was enhanced when the lead composition was higher (above 6wt.%). The present paper is aimed at confirming that the melting of an alloy containing a heavier solute may be accompanied with a stratification of the solute which exerts a stabilizing effect on the convective fluid flow. Results obtained from numerical modeling are compared with experimental data obtained from the benchmark facility."

Jan 1, 2012

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By Du Sichen

The present paper presents the modeling of gas-solid reactions in the case of the decomposition of CaCO3, describing the reaction kinetics on the basis of heat-transfer concepts which could be compared with thermogravimetric results. In the case of solid-solid reactions, the present paper describes the model developed for describing solid-solid reactions from dynamic X-ray diffraction technique, developed by the present team. The model has been successful in explaining the formation of spinel from MgO and Al2O3.

Jan 1, 2006

By Alexandre Bonan

The paper reports on the results of a kinetic study on the oxidation reaction of aqueous free cyanide ions with H202, in the presence of Cu(2+) catalyst. The variables and respective ranges studied were the following: (CN) ° = 10 -100 mg/l pH = 10 -11 (H202/CN) mol ratio = 1 -3 (Cu/CN) mol ratio = 0 -0.25 The results lead to the development of a semi-empirical model whish incorporates both the useful oxidation reaction and the parallel alkaline decomposition of H202.

Jan 1, 1992

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Henry Hu, Alfred Yu

"A numerical model has been developed to simulate heat and mass transfer phenomena occurring during a novel magnesium reduction process-the vertical retort technology. The model was based on the control - volume finite difference approach. Simulations were run to determine the effect of various processing parameters on magnesium reduction cycle time. The model predicted temperature distributions, heating curves, recovery ratio of magnesium, and total process times. The predictions were used to optimize the magnesium reduction process including dimensions of the retort, geometries of the reactant compounds, and productivities. The results indicate that the implementation of the optimized processing parameters significantly decreases the reduction time, and consequently increases the production rate as well as lowers the energy consumption.IntroductionMagnesium consumption has been growing considerably in the past decade [1]. Of the total magnesium production, 30% is produced by the thermal reduction (Pidgeon) process, and it is anticipated to be still the main technology for producing magnesium in future [2]. One of the advantages of the Pidgeon process is that it is capable of producing high purity magnesium demanded by both the automotive and aerospace industries. However, the inefficiency of heat and mass transfer taking place in the horizontal Pidgeon reduction process results in low productivity, high energy consumption, labor-intensive operation, large floor space and high capital investment. This limits the production scale of a horizontal Pidgeon reduction process [3].Vertical reduction processTo overcome the shortcomings of the horizontal magnesium reduction process, a novel vertical magnesium reduction process [3] for large-scale production has been developed, in which heat and mass transfer in the retort is enhanced. The new process shortens reduction time, reduces energy consumption and increases productivity. The vertical reduction system is comprised of a vertically-placed retort, a heating furnace and a vacuum system. A section of the vertical retort is illustrated in Figure 1. Since the retort is set vertically, instead of horizontally, the entire procedure of loading the reactants material in the new process is different from the one for the horizontal reduction process."

Jan 1, 2001

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Takashi Nagai, Hideaki Sasaki, Masafumi Maeda

"The production of solar cells is increasing dramatically and the shortage of polycrystalline silicon for these cells has become a serious problem, making development of a low-cost production process for solar grade silicon essential. An electron beam melting technique is known to be effective for the removal of phosphorus from molten silicon. Although the phosphorus is removed by preferential evaporation in this process, the rate of removal is not sufficient, and its improvement requires thermodynamic information on phosphorus in the molten silicon. In this research, the vapor pressure of phosphorus in equilibrium with a siliconphosphorus alloy was measured by double Knudsen cell mass spectrometry with a system blowing gas into the Knudsen cell. The activity of phosphorus in silicon, the Gibbs energy change of the dissolution of phosphorus in silicon, and other factors were estimated from the results. Using these data, we provided guidelines on how this process can be improved.IntroductionSolar energy is in great demand since it is inexhaustible and cleaner than that from conventional energy resources. Silicon is the material most widely used to convert solar energy into electricity. Figure 1 shows the recent production of solar cells. High purity silicon for solar cells, namely solar grade silicon (SOG-Si), has been commercially supplied mainly from off-grade high purity silicon in the semiconductor industry. However, production of solar cells has increased rapidly in recent years, and the shortage of SOG-Si has become a serious problem, so that a new processes which can produce SOG-Si economically are required.Directional solidification was applied to remove transition metal elements such as Fe or Ti by segregating them from the remaining melt. However, such solidification is useless for phosphorus because the segregation coefficient of phosphorus is nearly unity. Numerous approaches have been made in an attempt to produce a resource of low cost SOG-Si from metallurgical-grade silicon (MG-Si). [1,2]"

Jan 1, 2012

By Katsuyasu Sugawara, Takuo Sugawara, Shin-ji Abe, Tadakazu Kagami

"In order to clarify the mechanism and to obtain the fundamental data for heavy metal recovery from an incinerator ash by chlorination, pure chemical reagents, zinc oxide and lead oxide or the fly ash blended with calcium chloride and silicon dioxide were heated up to 1000°C in a nitrogen stream. Thermogravimetric curves of the samples with the chlorinating reagents indicated that solid-liquid reactions accelerated the chlorination and release of metals from the solid phase. The formation of liquid phase of calcium chloride played an important role on effective recovery of zinc and lead at lower temperatures below 800 °C. Although zinc and lead could be decreased in the incinerator ash without chlorinating reagents, addition of chlorinating· reagents enables the removal of metals in high extent· at lower temperature.IntroductionFly ash is discharged about 3,000 tons/day (about 110 million tons/year) from incinerators of municipal solid waste in Japan and mostly fly ash is disposed in landfills. Fly ash includes heavy metals e.g. zinc and lead. Since untreated fly ash caused hazardous leaching problems, Waste Disposal and Public Cleaning Law was revised in 1992, fly ash being designated 'specially controlled' general waste. Fly ash must be disposed by the following suitable, intermediate four methods: [I] Cement- Solidified Method, [2] Immobilized Chemicals Method, [3] Melting Solidified Method, [4] Acid Leaching Method, permitted by the Ministry of Health and Welfare, Japan."

Jan 1, 2000

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

By Alex Moyano

The Peirce-Smith converters are traditionally carrying out the converting process of a copper matte in the smelters of Codelco-Chile. However, its production increment is very limited due to the investment magnitude associated to the fulfillment of the environmental regulation. The objective of this paper is to present the Codelco continuous converting process technological advance when converting mattes and/or white metal into blister copper in a Teniente converter unit as an alternative to increment the corporative anode copper production. In 1994, Codelco-Chile started evaluating its ?home made technology? as an alternative to the traditional batch-type converting process. By the year 2001, the Caletones smelter converted liquid white metal to blister copper in a rearranged PS converter continuously. Then, during the 2001-2003 period, several pilot and industrial scale tests were done in a Teniente converter unit at Codelco Norte smelter, evaluating the continuous converting process, i.e., processing liquid mattes (62-68% Cu) to blister copper, demonstrating its technical feasibility with: (i) both constant production of gas flow and SO2 concentration, (ii) production of liquid slag, and (iii) production of a clean blister copper, suitable for the refining process. The promising results have led Codelco-Chile to plan for the 2006 period, a next advanced stage for the continuous converting process evaluation by carrying out a new campaign of tests in a Teniente converter unit at the Codelco Norte smelter.

Jan 1, 2006

By Peter Koh

The velocity solid charge attains when dropping down concentrate chutes is an important boundary condition when developing mathematical models of flash furnace burners and reaction shafts. In this work an experimental rig was developed to measure the velocity attained when nickel concentrate and sand were dropped down a vertical pipe 3m long. The velocity measurements showed that the nickel concentrate did not fall as individual particles. The measured values of the velocity approached, but did not attain, those calculated for solid bodies, the disparity being attributed to friction at the pipe wall and fluid drag losses. After falling 2 m velocities between 5-6 m/s were attained. The analysis was extended and applied to understanding the intermittent problem of puffing which sometimes occurs from the top of the concentrate chute. The pressure at the bottom of the chute is the net result of two opposing pressures, namely that developed by (a)the process air entering through the velocity control device, and (b) the solids falling down the concentrate chute. Flow back up the chute occurs when the former exceeds the latter. The process air pressures in the burner were obtained from CFD simulations of a full burner. Variables considered included air speed through the velocity control device, drop height and furnace draft. The analysis was useful in highlighting the operating conditions which were conducive to puffing and in establishing procedures to minimise its occurrence.

Jan 1, 2006

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 °C under different pressures of oxygen, In the range from 300 to 500 °C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By H. J. Thevik, A. K. Dahle

"A mathematical model that calculates the stress development in a coherent and stationary dendritic network due to interdendritic flow is proposed. The fluid flow is assumed to be related to the solidification shrinkage, and under the assumption of no porosity formation and unidirectional solidification, the shrinkage-induced flow within the mushy zone is calculated analytically. The interdendritic melt flow exerts a force on the solid network and an analytical expression for the stress build-up in the network is developed. Parameter studies illustrating the influence of cooling conditions, mushy zone length, dendrite coherency, fraction solid, volume fraction of eutectic, and solidification shrinkage upon the stress development within the solid network are presented. Comparing the magnitude of the calculated stresses to measurements of the strength in equiaxed mushy zones shows that it is possible for the stresses to exceed the strength, thereby resulting in reorientation or collapse of the dendritic network.IntroductionInterdendritic fluid flow is at present regarded as a very important mechanism for feeding of shrinkage during solidification of metal alloys. Solidification of many alloys is often characterised by heterogeneous nucleation of the primary phase on substrates in the melt with subsequent evolution of equiaxed dendrites. These equiaxed dendrites can initially grow freely, but impinge on each other and form a continuous dendritic network, ie. dendrite coherency, quite early in the solidification process. Measurements of the dendrite coherency point have shown that the dendritic network is established at solid fractions ranging between 0.1 and 0.5, and most often around about 0.2 [l]. Depending on the alloy composition this means that as much as 70 to 80% of the volumetric shrinkage has to be compensated by flow of liquid through the interdendritic network. Interdendritic flow occurs with a much larger resistance compared to free flow of the liquid and flow of a liquid with dispersed crystals. The pressure drop associated with the interdendritic flow increases rapidly with decreasing fraction ofliquid."

Jan 1, 1999

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997