Search Documents

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By David Dye

Good morning, everyone, and thanks Syd for that fine introduction. I am honored to be here to help you celebrate 25 years of advancement and success in the important field of ground control. I would also like to recognize Dr. Peng for his significant contributions in longwall mining and ground control. His contributions have had a major impact on improving safety and reducing fatalities in America?s mines. Thank you, Dr. Peng, for the important work you have carried on throughout the years. Many miners are alive today because of your dedicated work to protect them.

Jan 1, 2007

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By Anthony T. Iannacchione

The Solar No. 7 and Solar No. 10 mines were designed to prevent mine waters from directly discharging to the surface. In January of 2004, a discharge occurred as the Solar No. 7 mine was in its final stage of flooding through a barrier averaging 456-ft in width over a 1,600-ft length (No. 1). Another barrier (No. 2) was designed to protect four municipal water wells operating 1,800- ft away and producing from within or slightly below the Upper Kittanning coalbed from the adjacent Solar No. 7 and No. 10 mine pools. These two barriers were selected for this study because of varied mine layouts, mining methods, and geology factors affecting their performance. Analysis was aided by the collection and georeferencing of 6-month mining maps from the Pennsylvania Department of Environmental Protection (PA DEP). A structure contour map of the Upper Kittanning coalbed was constructed from mine map elevation points. These data and 2-ft surface contour maps were used to measure the precise location of the coal outcrop. The actual discharge point was as little as 425-ft away from a thinpillar section and 475-ft away from a pillar recovery section. The discharge point was found to be located slightly above the coal, indicating that the drainage path was at least partially through the strata directly above the Upper Kittanning coalbed. Hydraulic conductivities and potential discharge pathways are analyzed and discussed. The possible factors influencing the performance of the down-dip barriers at Solar No. 7 and Solar No. 10 are: a) the width of the barrier, b) the applied hydraulic gradient, c) the type of mining adjacent to the barrier, d) the overburden, e) the pattern and characteristics of fractures, and f) the quality of waters contained within the mine pools. This study, part of a larger effort funded by the Appalachian Research Initiative for Environmental Sciences (ARIES), is tasked to determine the key factors responsible for the successful design of down-dip coal barriers.

Jan 1, 2013

By Daniel W. H. Su

Underground roof geology reconnaissance is being conducted by CONSOL Inc. to enhance mine productivity. Often, roof instability within mine entries is the consequence of highly variable geology that cannot always be detected from information provided by widely-spaced surface core holes. Utilizing a combination of roof drilling data, geophysical logs, and borehole camera and fiberscope observations, roof geology mapping is conducted within longwall development entries in areas of specific concern prior to commencement of longwall mining, Depending on the uniformity of the site-specific roof geology, data point spacing along the longwall development generally ranges from one to five crosscuts. Surface core hole data are correlated with the roof geology mapped underground to validate the underground observations. Detailed roof geology maps can then be produced to enable ground control engineers and mine management to select cost-effective ground control techniques. However, this procedure is not necessary or useful in all situations and it is employed only when there is strong geologic evidence to justify a closer inspection.

Jan 1, 1999

By Michael Kelly

Longwall mining is the principal method of underground coal mining in Australia, with 70 million tonnes being produced by longwall mines in 1999. However, the mechanisms that control longwall geomechanics are still not clearly understood resulting in stoppages costing several hundred million dollars per annum The CSIRO has been investigating longwall geomechanics with consultant groups and minesites through several ACARP supported projects since 1994. The research has aimed to improve longwall support design and control methods by defining strata failure mechanisms and their occurrence about underground extraction panels, It also aimed to develop better predictive tools bur a broad range of underground environments. As a result of site studies at more than 8 locations some of the aspects that have been touted to control longwall geomechanics, especially from a 3D aspect are highlighted. These aspects include stress controls, geometry, faulting, depth. longwall width and changes in lithology.

Jan 1, 2000

By G. R. Corbett

Between 1977 and 1984, No. 26 Colliery, at Glace Bay in the Sydney Coalfield, suffered from a series of 37 rock/gas outbursts. These events were characterized by the complete pulverization of a sandstone which was propelled into the mine roadway and an associated release of methane gas. The events began to appear at a depth of 700 m and increased in intensity and damage to the excavation as the mining depth increased. At the time of the closure of No. 26 Colliery (as a result of an unrelated fire), these outbursts were the subject of intensive investigation. Although No. 26 is now closed, there is concern that similar events could appear at Phalen Colliery where current development work is proceeding at a depth close to the 700 m threshold. Past investigations into rock/gas outbursts included studies of in situ stresses, the simulation of outburst events in the laboratory, investigations into the potential for destressing an& degassing of problem sandstone and the development of numerical models to assist in the design of openings in outburst prone ground. However, despite this work, methods of predicting outburst conditions are presently limited to examination of probe hole cores for core discing, and methods of working under such conditions are limited to boring and firing and using volley firing techniques to initiate any outbursts while workers are safely out of the heading. During this investigation of worldwide occurrences of this phenomena, literature obtained suggested that outbursts might generate microseismic precursors. An intrinsically safe (IS) microseismic monitoring system was designed and developed based on CANMET's rockburst monitoring system currently in use in hardrock mines, and installed in a development roadway at the deepest extent of the Phalen Colliery. The system will record microseismic activity associated with development work to try to identify characteristic precursors of outburst-prone conditions. This paper describes the steps taken to identify a microseismic system suitable for use at Phalen colliery, of which part of the requirement was that it be IS and approved for use in the Sydney Coalfield. The modifications to the selected system are described, along with its capabilities and the preliminary results of its performance over the first few months of use.

Jan 1, 1994

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By John A. Rusnak

"This paper discusses the variation of coal strength based on the megascopic coal lithotypes for Central Appalachian high-volatile A coal beds. The composition of coal beds is complex and variable, depending on the depositional environment associated with original plant material, inflow of clastic material, and water level fluctuations in the original swamp/mire environment. Thus, different types of coal and sediment are formed within each coal bed. These differences in coal composition were first classified by Marie Stopes, a paleobotanist, in 1919. The classic coal megascopic lithotypes are vitrain, clarain, and durain, which correspond to bright, bright banded, and dull coal, respectively. Stopes also identified that the lithotype fusain, which is mineral charcoal, has no inherent strength and can act as a plane of discontinuity. In this study, two other coal-bed lithologies are also considered—bone and carbonaceous shale. This makes for a comprehensive suite of coal-bed stratigraphic components apart from rock partings. A total of 1,000 uniaxial compressive strength (UCS) and 440 indirect tensile strength (ITS) tests were conducted on cores from southern West Virginia that were specifically logged and described using the megascopic coal lithotype nomenclature. Statistical analysis is presented showing the results for each lithotype group with mechanical properties correlated to the lithotype. Previous studies have analyzed the mechanical breakage properties associated with coal lithotypes, which correlate well with these results. However, coal rank does appear to be a contributing factor, and this study is confined to only high-volatile A bituminous rank. Application of these results would be well suited to a rock mass classification system to address coal pillar rib stability. This would allow for rib support design and implementation to consider relative coal strength by visual observation of the seam stratigraphy through ongoing observations within a mine. Changes in seam composition can be readily identified, allowing the adjustment in rib support design. Another application would be for the determination of numerical modeling inputs based on detailed seam stratigraphy. However, these results, even with the standard strength reduction criteria, may not be applicable to currently accepted empirical coal pillar design procedures."

Jan 1, 2017

By Robert M. Cox

The successful application of the science of rock mechanics to the practical problems of coal mine design requires the acquisition and reduction to useable form of large amounts of field and laboratory data, and the construction and analyses of numerous geostructural models containing a wide variety of geometric and physical strength variables. Typically, the rime constraints placed on a new mine design project coupled with the inherent complexities of a good rock mechanics study combine to limit the applications of rock mechanics to the most rudimentary level. To facilitate a better application of rock mechanics to mine design problems, an interactive software package has been developed for use on a graphic mini-computer system that serves to aid the engineer in the timely and efficient analyses of rock mechanics data and geostructural models. The first phase of the rock mechanics package solicits the input of the raw geologic and rock strength data, analyzes and arranges this data in a logical manner, produces complete listings and statisitical summaries of the various rock properties, and stores the data on magnetic tapes and disks to serve as a future Rock Mechanics Data Base. The second phase of the software package provides for the analyses of a variety of geostructural models using a wide variety of geometric variables coupled with the rock strength data stored in the Rock Mechanics Data Base. This software package allows for the evaluation of numerous geostructural mine models for the design and selection of mine roof support and pillar systems (see Table l).

Jan 1, 1982

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984