Search Documents

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By W. E. Roscoe, K. N. Spence

In the Canadian mining industry, there are at present no comprehensive regulations or standards for valuation of mineral properties. In January 1999, the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. The authors were subsequently appointed Co-chairs of the CIM Special Committee on Valuation of Mineral Properties (CIMVal). A committee of experts from the mining industry, consulting, financial and legal communities was established with the task of reviewing available information, investigating various valuation methodologies and practices, soliciting input from interested parties, and recommending a Canadian code or standards plus guidelines for the valuation of mineral properties. As an initial stage of its work, the CIMVal Committee organized a one day session at the Mining Millennium 2000 Convention in Toronto in March 2000 on valuation of mineral properties. The 10 invited papers have been published by CIM. As a second stage, CIMVal has requested input and comments from all interested parties. The next stage will be to prepare a preliminary draft with a recommended code or standards and guidelines. This will be circulated for further input and comments prior to revision and publication of another draft. The final CIMVal report should be completed in early 2001. A variety of methods are in common usage for the valuation of mineral properties, depending on the stage of development of the property, the data available and the experience of the valuator. For example, the discounted cash flow method is commonly used for properties in production or at the feasibility stage, but is not generally considered appropriate for exploration properties. Market approaches such as comparable transactions are in wide general use, and various cost approaches are used for exploration properties. The option pricing approach has promise for valuation of marginal properties, but is not commonly used.

Jan 1, 2001

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermo-physical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at the University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous case is modeled with walls, each having a different set of thermo-physical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By Qingqing Huang, Mohammad Rezaee

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 12th MPD Student Poster Contest on March 2, 2022, during the MINEXCHANGE 2022 SME Annual Conference & Expo. The event showcased the work of 32 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to explain their research to a panel of judges during the conference. Recognizing the students’ efforts in working hard on their research topics and setting aside time to complete the necessary steps to enter the poster contest, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 22, 2022

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By Colin P. Pigott

The paper describes a variety of existing techniques and equipment which when combined together permit faster and cheaper drilling of shafts in soft to medium strength formations. Drilling fluid circulation, methods of hole stabilisation and bit design, including the advantages of flat bottomed and conical bits, shrouds and skirts, tungsten carbide, long tooth and disc cutters are considered. The principles of rock chip transportation and bottom hole cleaning are described together with a new and very efficient fluid circulation system which was invented by the author.

Jan 1, 1985

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By Martin Stone

Industrialized countries, particularly the United States and the United Kingdom, remain at the forefront of international efforts to control the potential disruption from computer malfunctions caused by the date change from1999 to 2000 — widely known as the millennium bug or Y2K. Disruption is least likely in the developed world, including the United States, Canada, western Europe, Japan and Australasia. However, the picture is potentially different in developing countries where many mining companies operate. The less developed the country, the greater the chance of some form of Y2K-linked disruption.

Jan 1, 1999

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By R. Q. Honaker

Dense medium processes are used to clean over 50% of the coal that is fed into preparation plant facilities worldwide. The dense medium is formed using ultrafine magnetite which is recovered after the cleaning step using drain-and-rinse screens and magnetic separators. Despite the high efficiency of the recovery system, magnetite losses of around 0.5 to 1.0 kg/ton are common. Considering the recent escalation of magnetite to around $300/ton, an alternative source of magnetic material from coal combustion bottom ash has been investigated. A relatively low cost recovery system has been developed. Dense-medium tests using the bottom ash magnetics revealed a high level of efficiency as indicated by probable error values around 0.03 over the range of medium densities investigated. The results from both the recovery and coal cleaning efforts will be discussed in detail.

Jan 1, 2009

By Phil Pennington, D. Jack Adams, G. Ward Wilson, Virginia T. McLemore, Luiza Aline F Gutierrez, Rodney Shields, Steven Lockwood, Samuel Tachie-Menson

Microorganisms are directly or indirectly involved in many chemical alterations and in the decomposition of minerals required for their growth. Microbial dissolution of sulfide minerals under acidic conditions can produce over 1,000 times more Acid Rock Drainage (ARD) than chemical action alone. Microbial actions can cause precipitation of minerals, adsorption or release of metals, and formation/destruction of organic-metallic complexes. Soluble minerals can serve as oxidizing substrates, electron donors/acceptors in redox reactions, and can be directly involved in cell metabolism. Microorganisms and microbial oxidation-reduction reactions and their contribution to mineral mobilization and stabilization will be discussed.

Jan 1, 2005

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

Several common ratios used for determining spontaneous combustion activity rely on comparing the amount of various products of oxidation with the amount of oxygen consumed to produce these products. As coal gets hotter, oxidation reactions become more efficient meaning more products produced for less oxygen consumed. There are many problems associated with accurately determining the true amount of oxygen used. These problems relate to the monitoring technique (and its associated uncertainties) used to generate the results, deficiencies in the established equations utilized in calculations, dilution with other gases and other sources of oxygen depletion. Typically the oxygen deficiency is over estimated, resulting in the under estimation of the indicating ratio. For this reason the use of ?one off? calculations to determine the status of the underground environment is not recommended. Instead trends of these ratios should be used to identify increases which indicate an increase in oxidation intensity. This paper outlines problems associated with the monitoring techniques and equations used to determine the oxygen deficiency.

Jan 1, 2009