Search Documents

By M. H. Basiri

The application of aluminum matrix composites, due to their unique properties, is significantly growing in the variety of industries such as aerospace and automobile. In comparison to other light metals, such as magnesium and titanium, aluminum is lower in price. These are the advantages that this metal dominates the others. In this research, first by applying the lost foam casting method, the SiCp/A356 composite was cast in the bottom and side gate conditions with 690°C and volume fraction of 10%. Furthermore, the effects of reinforcement particles (60 µm, 75 µm) were examined. The results present the particles distribution in the side gate methods is more homogeneous than the bottom gate casting method. Also, by increasing the particles sizes, the fading rate in the side gate are reduced from 22% to 19%, as well as from 26.4% to 25.4% in the bottom gate. Key words: Carbide-Silicone Particle, Gating System, Composite Micro-Structure, Foam Casting

Feb 27, 2013

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

Beneath some of New York?s most iconic buildings ? The Met Life Building, the Helmsley Building, the Waldorf Astoria ? crews are busily at work on the Metropolitan Transportation Authority?s long-awaited East Side Access (ESA) project. In fact, it is 14 floors beneath the famed Grand Central Station where one of the centerpieces of the project, the new Long Island Railroad (LIRR) station terminal, is being blasted and carved into shape. When completed in 2016, the $7.3-billion ESA project will increase LIRR?s capacity into Manhattan and significantly relieve congestion at Penn Station. Currently, 37 LIRR trains per rush hour roll into the crowded Penn Station where many riders must then transfer to subway trains to complete their commute. When completed, the ESA tunnels will bring an estimated 160,000 riders directly to Grand Central Station, saving those riders 30 to 40 minutes. Studies have found that more people work within walking distance of Grand Central than Penn Station. ?The benefits of the project are tremendous,? MTA Capital Construction President Michael Horodniceanu told more than 340 industry professionals attending the UCA of SME?s George A. Fox Conference in New York on Jan. 26. ?The ESA is the first expansion of the LIRR in 100 years. It will increase the East River tunnel capacity by 50 percent and will help support job growth around Grand Central.?

Jan 3, 2010

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By D. R. Shoemaker, H. W. Judges

A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first produc¬tion is scheduled for early 1983. The company expects full capacity-9 Gg of molybdenum per year-to be reached in 1984.

Jan 6, 1980

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By G. Aggistalis, N. Kazilis, C. Rawlings, N. Rachaniotis, S. Raptopoulos, M. Knights, R. Game

The Egnatia Odos (Odos meaning road) is one of Greece’s largest ever highway construction projects and one of Europe’s most important. The Highway will assist in the connection of the Greek Ionian/Adriatic Coast with Turkey and the Black Sea reviving an historic Roman alignment “Via Egnatia” connecting Rome to Constantinople (now Istanbul). There are 74 twin tunnels (60 bored and 14 cut-and-cover) with lengths ranging from 160 m (175 yd) to 4,600 m (5,031 yd) and 100 m (109 yd) to 270 m (295 yd),respectively. The complex geology and resulting physical geography have had a major influence on both the design and construction of these tunnels. This paper describes the management, design and construction challenges of these numerous tunnels.

Jan 1, 2005

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By J. E. Bernick, J. Davies

This paper describes the design and construction of a 22.86 m (75 ft) long jacked tunnel, which was successfully installed, despite difficult mixed face conditions at Metro-North’s Westport Station, in Connecticut in the fall of 2003. The tunnel utilized what is believed to be, the first application of a steel grillage system within the United States. This grillage was installed before the jacking started and allowed the tunnel to be jacked under four live railway tracks, which included the Acela high speed line, without affecting train operations. The clearance between the top of the tunnel and the rails was only 0.9 m (3 ft).

Jan 1, 2005

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

By L. M. Lenahan, J. D. Sheets

INTRODUCTION The Raleigh-Durham International Airport (RDU) in North Carolina is the fourth largest airport in the southeast region of the United States. The Raleigh-Durham Airport Authority is currently underway with planning, designing and constructing are placement Passenger Terminal as part of the Major Capital Improvements Program at Raleigh Durham International Airport. The Terminal C Expansion and Renovation Project will replace the existing Terminal C structure with a new processor building and concourse. The project is separated into several contracts. The early stage contracts are constructing a west side storm water management facility, relocating taxiways, installing new drainage systems, installing new aircraft apron pavement, Demolition, the Central Energy Plant and Early Foundations. The later projects are the Terminal Building, Passenger Boarding Bridges, Information Technology Systems and Integration, Furniture, Furnishings & Equipment and Specialty Millwork. The Terminal Building will be constructed in two phases. Phase 1 constructs the north half of the new terminal. Airline operations will move to the new terminal at the completion of this phase. Phase 2 completes construction of the south processor building. The full build out of the project, subject to funding availability, will replace the remainder of the south concourse. The Program’s primary focus is to replace the existing passenger Terminal C with a new terminal that will provide more passenger gates and larger passenger screening, ticketing and baggage handling facilities. The planning for the New Terminal C Program began in 2002 with construction starting in March, 2003. The continuing growth of passenger airline travel in the Raleigh/Durham metropolitan area requires RDU to expand its facilities to keep up with the present and future growth within the Region. In October of 2002, the RDU Airport Authority selected Parsons Transportation Group as the Program Manager/Construction Manager to help assist in the development of the Terminal C expansion program. RDU Airport Authority selected the Seattle Washington Office of URS Corporation as the Engineer of Record for the West Side Storm Water Management Facilities. The Westside Storm Water Management Facilities Project became one of the early critical path activities of the overall RDUAA Terminal C Expansion Program. The Briar Creek Reservoir had been constructed to accommodate storm water runoff to the west of the Airport. The existing 1.5 m culvert that drained runoff from the airport terminal (area) to the reservoir was insufficient in supporting the additional flows

Jan 1, 2005