Search Documents

By D. S. Loubser

The technique of backfilling in the gold mining industry is dependent on the dewatering of slurry to form a solid support system. In many cases flocculants are added to the slurry to increase the rate of dewatering. To ensure that a stable support is obtained it is important that the chemistry, application and limitations of these flocculant additives are understood. Flocculant additives have to be added at a point where minimum shear will occur. (Shear occurs when a flocculant is exposed to excess energy resulting in breakdown, of the floc.) To ensure that optimum results are obtained it is important that personnel involved are trained to use the flocculant additives and dosing equipment correctly.

Jan 1, 1988

By N. Graham, C. Walker

The SORD Miner is a patented mining principle being developed to exploit mineral and energy resources that current technology can not access. SORD Miner is designed to operate in underground wet, granular, continuously collapsing geological environments such as alluvial and marine deposits. It is somewhat like a cutter suction dredge and should be capable of mining its way through any fine granular material like sand or gravel, pumping the slurry back to the surface. In areas where the target layer is covered, the SORD Miner is inserted below the water table and will tunnel its way to the mineral deposits at depth. This paper describes the development, concept testing and prototype construction of the SORD Miner.

Jan 1, 2007

By G. Rebel

Owing to the helical construction of the wires and strands in a triangular-strand rope, a torque is generated when the rope is restrained and tensioned. When a rope is suspended vertically, there is a load differential along its length due to the self weight of the rope. This load differential gives rise to an initial torque differential m the rope. Since the rope is constrained only at the conveyance and sheave wheel, the torque along its length must be constant ID order to maintain equilibrium, a variation in lay length occurs so that the lay length at the conveyance end decreases, and the lay length at the sheave end increases, from the manufactured state. The tension-torsion testing of steel-wire ropes is discussed, and it is shown how the results of the tests can be used to predict static in-shaft torsional behaviour. The expected changes in strand lay length in very deep shafts (deeper than 2500 m) are calculated, and the associated problems and of severe changes m lay length on rope endurance and safety are discussed. Examples of current in-service rope distortions such as kinks and corkscrews are shown.

Jan 1, 1996

By J. Kitagawa

The principal objectives of a metallurgical test programme for a 'grass roots' mining project are twofold. The first requirement is to establish the metallurgical viability of the project by demonstrating that acceptable results can be obtained by processing of the ore. The second goal is to obtain essential supporting data to determine whether the project is economically feasible. This involves several functions, which include the establishment of a workable flowsheet, the obtaining of design criteria for the commercial plant, and the collection of the evidence necessary to convince management, and often a third-party expert, that the metallurgy predicted for the ore can be achieved in a full-scale operation. The latter task is facilitated if a coherent overall picture is presented considering the geology of the orebody, the mining plan, and the mineralogy and metallurgy of the ore. The purpose of this paper is to provide guidance in the establishment of a test programme to meet the above objectives.

Jan 1, 1978

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By A. N. Brown

The importance of the minerals industry in the economy of the country is discussed, and the tremendous changes that have taken place over the past two decades, including the widespread application of computers and the use of mechanization, are outlined. A discussion of the future of the minerals industry points out that, with the rise in the price of gold, the life of the gold-mining industry can be expected to extend beyond that previously predicted, and that the demand for uranium, which has been depressed, is uncertain. As a result of the oil crisis, the demand for coal has increased and large expansion programmes are planned. These involve coal exports and the use of coal for the generation of electric power, for the production of liquid fuels, and for the smelting of metals. Technical challenges face engineers in every avenue of the minerals industry: in deep gold mines, underground coal mines, strip coal mines, and open-pit mines. Studies indicate that only one-third of the demand for trained mining and metallurgical engineers is being met and that the position is worsening. However, there are indications that the industry is succeeding in attracting more engineering students, and the supply is expected to improve. These efforts should be co-ordinated, expanded, and intensified. There is a need to ensure that sufficient teaching staff of the right calibre and experience are attracted to universities and technikons. The first degree course is comprehensive and basic, and specialization through post-graduate study should be encouraged. The influence of national service on the education and training of engineers is discussed.

Jan 1, 1982

By S. M. Rupprecht

"Artisanal mining is basic mining characterized by manually intensive work methods utilizing primitive or simple equipment and conducted by individuals or small groups exploiting deposits. Artisanal mining in Rwanda and Burundi is further complicated in that the techniques applied are often inadequate, resulting in low productivity and poor recoveries, and workers are paid low wages with owners reluctant to reinvest in the mining operations. A consequence of this vicious circle is often poor working conditions, with miners operating under unsafe and/or unhealthy working conditions. An additional problem is that mining is conducted in a manner that is detrimental to the environment.Artisanal mining is commonly more dangerous than large-scale modern mining operations. Artisanal operations are generally subsistence activities with the miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. Machinery tends to be expensive and often far beyond the reach of most artisanal miners, and therefore there is a general tendency for workers to focus on labour intensive and riskier mining methods.This paper proposes the introduction of small-scale mechanization with labour-intensive manual mining utilizing a bench mining approach in artisanal mines operating in Central Africa. From the 1950s to the 1980s bench mining was successfully conducted in Burundi utilizing manual labour. In order to achieve a balance between job creation and project economics, the combination of manual and mechanized mining is proposed. Manual mining offers the benefit of local job creation while ensuring good mining techniques, such as minimizing mining loses and dilution. Through the introduction of mechanized loading and hauling activities, areas of high stripping ratios can be viably mined, thus increasing the amount of resources that can be exploited. The use of a loader and tractor-trailer arrangement is proposed, thereby improving throughput, productivity, and worker safety and, reducing the impact on the environment."

Jan 1, 2017

By J. D. Wells

An account is given of the planning required for the rehabilitation of land that is to be disturbed by opencast mining, and of the preparation of rehabilitation of land that is to the Inspector of Mines. The plans Include the provisions that are to be made to allow for climatic conditions, land use, vegetation and wildlife, surface-water resources, geology and ground water, soils, land capability, rehabilitation method, location of discard dumps and slurry ponds, pollution control, and costs. . . Monitoring of the operation is the only way that the rehabilitation plan can be improved, and both monitoring and planning are essential when provision is being made for the closure of a mine.

Jan 1, 1986

By T. Dimillo, R. G. B. Pickeirng

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular ore bodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focussed on the haulages, cross cuts and raises. The non-explosive rock breaking method has many other applications, however, it is the integration with the Tunnel Digging Machine that results in the first, cost effective, Continuous Tunnelling Machine for hard rock mining.

Sep 1, 2001

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006

By D. Rankin, H. J. Stucke, W. K. B. Loftus

SYNOPSIS Planning for the Finsch opencast mine is described with particular reference to the proposed stages of mining, the method used to determine the limits of surface waste rock stripping and the derivation of the waste rock mining rate. Actual mining practice is described and the possibility of installing a skipway into the open mine at a later date is discussed. In addition, the waste dumping policy is referred to: this includes the cutting of slots through the hill on the west side of the pipe to increase tramming speeds. The crushing, washing and recovery sections of the treatment plant are described together with the various changes being made to the circuit. The most important of these are the installation of X-ray sorters for the final recovery of + 7 mesh diamonds, and the vibrating grease belt for the recovery of - 7 mesh diamonds. INTRODUCTION The Finsch Mine, a subsidiary of De Beers Consolidated Mines, Limited, is situated approximately 90 miles west of Kimberley, and some two miles from the village of Lime Acres, in the Northern Cape. Lime Acres is a company village shared with the Northern Lime Company which operates a limestone quarry and works near the township. The mine is near the southern end of a well mineralized belt producing limestone, asbestos, diamonds, manganese and iron ore, and the whole area has developed rapidly in the last 20 years. Power for mining operations is drawn from the Electricity Supply Commission. The mine is conveniently close to the main Kimberley-Postmasburg railway line. Water is drawn from the Vaal River through a 57 mile State-owned pipeline at present temporarily operated by mine staff. DISCOVERY AND PROSPECTING OPERATIONS The diamondiferous orebody is situated on the farm Brits, which is State-owned ground that has been leased to the Company for the period of mining operations. There are indications of interest in the area by prospectors (Richter, de Bruin and others) over a period of some 30 years and the discovery would possibly have been made years earlier but for a law preventing prospecting for precious stones on State-owned land. Although the pipe formed a clear depression on the hill where it was situated, it was overlain by some 5 to 40 ft of banded ironstone rubble which was washed into the depression from the hillside above the pipe and obscured the deposit. In 1958, Mr Allister Thornton Fincham applied for, and was granted, the right to prospect for base minerals on the farm Brits. Asbestos is known to occur in the area and, initially, was Mr Fincham's primary interest. However, during the prospecting operations, garnets were discovered and it was realised that diamonds might be present. In 1960, when the Precious Stones Amendment Act was passed, a company

By M. D. G. Salamon

In view of an urgent need for a simple means of simulating the behaviour of stratified rock masses, a long-dormant linear model is revived, generalized, and discussed in some depth. The model is piecewise homogeneous, consisting of a pile of homogeneous isotropic laminae in which the interfaces between beds are parallel and free of shear stresses and cohesion. The continuity of stresses and normal displacements is assured across the bedding planes and, to maintain simplicity, the theory of thin plates is used as the kernel of the model. The paper covers the case where the rock mass consists of discrete beds in which the layers are arranged either heterogeneously or systematically. The stratification is regarded as uniform when all the layers are of the same thickness and their Young's modulus changes exponentially with depth; and as homogeneous when all the laminae have identical thickness and properties. The case of uniform stratification is also treated on the basis of an equivalent quasi-continuum derived from the basic model. Attention is focused on the derivation of influence functions. It is demonstrated that the quasi-continuous models, when they are available, can replace their distinct-layer counterparts. The homogeneous quasi-continuum, which permits the derivation of its influence functions in closed form, facilitates the determination of the roof and floor convergence. In the case of a significant class of problems, the convergence distribution is defined by a second-order differential equation in the xy plane, which simplifies to a Poisson's equation if the mining excavations are unsupported. With this result, the paper prepares for the solution of a host of practical problems. These solutions are presented in a series of papers that are in the course of publication.

Jan 1, 1991

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluent is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10 mg/[l] cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a preneutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40 g/[l] NaOH. A preneutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By J. E. Forbes, B. K. Loveday

The role of gravity concentration in the recovery of gold from typical South African gold ores is described. The location of the concentrator in the grinding circuit is discussed, and typical capacities and operating costs are given. Some operating problems are mentioned, but the performance of concentrating equipment is not dealt with in detail since this to some extent depends on the nature of the ore. It is concluded that the main benefits are an improved recovery of coarse gold and a reduction in soluble loss. The use of a long leaching time and a carbon-in-pulp recovery system may eliminate the need for gravity concentration. but gravity concentration is seen as an inexpensive way of improving the recovery on existing plants.

Jan 1, 1982

By A. Ball

A fully instrumented laboratory drilling machine is described. It is designed to produce realistic drilling conditions with diamond microbits of 20 mm diameter. A computer-controlled data-logging system records the net power consumption, rotational velocity, bit thrust, torque, and penetration rate. Tests can be conducted under conditions of set thrust and rate of advance. In the tests reported, there is a significant correlation between the rock drilability and the measured rock properties of relative abrasion resistance and uniaxial compressive strength. Wear of a diamond bit is a crucial factor that cannot be determined simply from rock properties. Realistic drilability testing with appropriately scaled microbits is a convenient and economical way of evaluating diamond-bit performance and determining rock drilability.

Jan 1, 1990

By S. M. Rupprecht

The transportation of men, material and rock in mechanization programmes is often neglected, or at least plays only a secondary function, as the primary focus is on proving the technology. This is despite recognition of the fact that mechanization is essential if gold mines are to remain competitive. However, the use of totally mechanized systems will require further research in the short to medium term before they become generally available. Thus, there is a real need to improve mechanized men, material and rock transportation systems as they are currently used. This applies to both reef horizons as well as to horizontal transport systems. Keywords: Transportation, rock handling, material handling, men transportation, face cleaning, gully cleaning, continuous scraper, monorail, mechanized raise climber, mechanization.

Sep 1, 2001