Search Documents

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By L. Wade

The University of Nottingham, in conjunction with the University of Kentucky and The Society of Mining Engineers of America, hosted the International Symposium on Underground Mining Methods and Technology from 8th to 10th September, 1986. The programme was based on the central theme 'Coal Mining under Adverse Conditions'.

Jan 1, 1987

By K McLeod

{Figure 1} The Placer Dome-Western Areas Joint Venture?s South Deep Twin Shaft Complex, has been planned and dreamt of for nearly 20 years. [ ] The gold reserve at the bottom of these shafts is one of the largest single intact gold deposits remaining in the world today, containing an estimated 57 million ounces. This is about the size of the fictitious reserve created by inventive prospectors for the infamous BREEX scam in Kalimantan about ten years ago and about the size of the reserve Harmony claims as its own in it?s current hostile takeover bid for Gold Fields. So it is certainly of the magnitude that dreams are made of. [ ] {Figure 2} The unique orebody lies in a continuous, highly concentrated, thick deposit, an estimated twelve kilometres along dip and a two kilometre wide strike. Due to the thickness of some sections of the reef, up to 60 metres in places, bulk mining methods will be required for it?s extraction. [ ] {Figure 3} The twin shaft system comprises a main shaft which had an initial design depth of 2765m and a ventilation shaft of 2760m, making them the world?s deepest to be sunk in a single lift. The shafts were

Jan 1, 2005

By D. Almond

Low-grade, complex mineral deposits have resulted in the need for complicated large-throughput processing plants delivering increased productivity, reliability, and utilization, together with reducing operational costs. Complex mineralogy has resulted in complicated process flow sheets designed to recover minerals as efficiently as possible. In addition, the remote location of many minerals-processing plants, continuously rising energy costs, and fierce competition pose significant challenges to the modern mine, compounded by a global scarcity of qualified and experienced operational personnel. Over the last decade the Internet and automation technologies have undergone major advancements. Automation technologies, solutions, and concepts that existed, but were considered risky or unreliable prior to the year 2000, have now gained acceptance and matured. Furthermore, new technologies and different collaboration schemes have appeared, offering innovative solutions to the mining industry to address many of the challenges described. These advancements in reliable remote systems that access technology through the Internet provide significant opportunity to support mining operations, enhance process performance, provide engineering services, and proactively anticipate and execute maintenance services. This paper references a global survey of automation trends in the mining industry and the potential for an intelligent collaborative environment using automation technologies to exploit opportunities in operating the plant of the future, increasing effectiveness, and reducing operational costs. A variety of possibilities are described, including asset management solutions, remote access capabilities, performance monitoring solutions, advanced process control technologies, and the formation of an intelligent collaborative environment. A real example where this technology is used to support the operation and maintenance at a cement plant in Egypt is given to underpin the concepts described in this paper.

Jan 1, 2012

Introducing your Council. Mr J. S. Freer, Pr. Eng., after matriculating at Michaelhouse in 1944, obtained a B.8c. degree in chemistry and biology (1948) and a B.Sc. (Hons.) in chemistry (1949) from the University of the Witwatersrand. Mr G. C. Thompson matriculated at Dale College in 1951. He then attended the University of the Witwatersrand, where he obtained a B.8c. (Min. Eng.) in 1959. Mr P. T. Fewell was born and educated in the United Kingdom. After obtaining the degree of Bachelor of Engineering (Mining) in 1958 at Sheffield University, he emigrated to South Africa. DtP. R. Jochens, Pr. Eng., has been a member of Council since 1974, serving as President in 1980-1981.

Jan 1, 1984

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

By N. A. Barcza

INFACON 7, the seventh International Ferro Alloys Congress, took place in Trondheim, Norway, in June 1995. The main aim of the Congress, which was held under the auspices of Euroalliages and the Norwegian Ferroalloy Research Organization, was to present the challenges facing the ferro-alloys industry on the road to the 21st century. Halyard Tveit, Chairman of the Technical Committee, summarized these as: ? the transition to a single global market economy ? new demands with regards to quality arising from customer needs, and ? increased awareness of the global environment. In the Plenary Sessions Kouichi Nakamura (Nippon Steel) outlined, from the steel industry's point of view, the relationship between technical advances in the products and more demanding ferro-alloy specifications. Advances in steel manufacturing technology and higher product quality have been supported in the past by raising the quality standards of ferro-alloys. Future requirements are bound to bring about more severe standards, and these need to be established by common agreement between both industries.

Jan 1, 1996

By R. L. Machunda, A. M. Rugaika, D. D. Mdachi

Sedimentary and igneous rocks are the two primary sources of phosphate that are mined and beneficiated to fertilizer. During the beneficiation process, phosphate is lost into the tailings. We investigated phosphate concentrations in tailings dumps at Minjingu mine, Tanzania using energy-dispersive X-ray fluorescence spectrometry to quantify the chemical compositions. The phosphate content in the tailings varied from 12.91% phosphorus pentoxide (P2O5) in Tailings 2 to 19.61% in Tailings Dump 1. The naturally occurring phosphate concentration in rocks ranges from 3% to 35%, and phosphate tailings from various locations with P2O5 concentrations as low as 6.46-12.65% have been beneficiated to commercial fertilizer. Our investigation revealed that phosphate concentrations in Minjingu tailings may be sufficient to be recovered for commercial applications. Suitable recovery methods are discussed, and we recommend that beneficiation should be performed to minimize the loss of phosphate into tailings. Further research is needed to identify the optimal beneficiation methodology.

Aug 8, 2024

By C. E. More

Some observations on 'ancient' mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By N. Lock

"Despite the pre-eminence of the Jwaneng Diamond Mine as the world’s richest diamond mine, the discovery story has long been clouded in mystery. This is the 45-year old untold story of the Jwaneng discovery and contemporaneous Bechuanaland/Botswana political and socioeconomic history. Diamond exploration by De Beers in Bechuanaland began in 1955, with the first true kimberlite discovery near Letlhakane in 1967, before Clifford’s Rule was applied and before the use of indicator mineral chemistry. Surface deflation soil sampling and bioturbation by termites was the foundation for exploration into the Kalahari. The 1962 reconnaissance programme south of Jwaneng had failed to make any discoveries. Improved sampling methods were applied to the Kalaharicovered areas in 1969 and positive results were received by year-end. The Whateley’s Wish percussion drill-hole in December 1972 was confirmed as Jwaneng 2424D/K2 with drill core in early 1973. Jumper drills were required to penetrate the Kalahari sand cover. Diamond resources were demonstrated despite multiple technical problems. IntroductionThe Jwaneng Diamond Mine is, by value, the world’s richest diamond mine. Harry Oppenheimer is quoted as saying that Jwaneng is ‘the most important primary deposit found anywhere in the world since the discovery at Kimberley more than a century ago.’ (Taylor III, 1982) The mine opened in 1982 after some nine years of evaluation and construction since discovery in February 1973. Debswana (2017) states that 2015 production was 7.87 Mt of ore from which 10.408 million carats were recovered at a grade of 132 carats per 100 t (cpht). Although the value is not reported, it was noted that Jwaneng contributes 60–70% of Debswana’s total revenue from all mines, including Orapa, Damtshaa, and Letlhakane (Debswana, 2017)."

Feb 1, 2019

By Dave Deglon, Andrévan der Westhuizen

Objectives ?Survey typical Met Accounting streams at the Zincor refinery ?Determine Precision in Metal Conc?s Measurements for Monthly Met Balance ?Determine the Components of Variance in these Met Acc Values (Sampling, Preparation, Analyses) ??Common plant practice? should be mirrored even though not always in perfect agreement with ?laid down procedures? or ?good practice? ?Mass Measurement and Inventory Measurement was considered in less detail ?not reported here

Jan 1, 2005

This Spotlight gives a brief summary of the proposed 1991 tax amendments of relevance to mines and mining houses. It should be read together with the author's article South African mining tax in the 1990's', which appeared in the August 1990 issue of this Journal. A number of tax amendments of relevance to the mining industry were proposed by the Minister of Finance in his March 1991 budget speech. In addition, certain other measures that may be implemented were set out in the budget review document released at the same time. A word of caution is necessary: these measures will become law only if and when they are enacted in the appropriate legislation. When this legislation is tabled in June, it may not contain all of the measures discussed below, some of the measures may appear in modified form, and other measures not discussed at the time of the budget may well appear. Unless otherwise stated, the 1991 tax amendments will affect companies with years of assessment ending in the twelve-month period to 31st March, 1992.

Jan 1, 1991

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology's financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested into developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late eighties and early nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2003

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By I. Nolet

Matte tapping is one of the most critical operations of a matte smelter. Every smelter has developed particular matte tapping practices and tap-hole repair strategies that are often based on the experience of the smelter personnel. As a result, very little information has been published on these critical topics. This paper aims at providing the information gathered from a survey conducted in the PGM and Ni industries on matte tapping practices and tap-hole maintenance strategies for different PGM-Ni matte smelting operations.

Jan 1, 2014

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019