Search Documents

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By Stephen Simukanga, Jewette Masinja

"Mining has been going on commercially in Zambia for over 100 years. The backbone of the mining industry has been copper production and its by-products of cobalt and gold. Over these years, the mining industry ownership structure has swung from private ownership to state ownership in 1972, and back to private ownership in 1995. Environmental management was first introduced into the body of Zambian legislation in 1991 through the promulgation of the Environmental Protection and Pollution Control Act (EPPCA). The Act’s main functions included the protection of the environment and control of pollution, and in particular to provide for the health and welfare of the people, animals, plants and the environment in general. This Act, was replaced in 2011 by the Environmental Management Act (EMA). The new Act has a number of new elements including: mainstreaming environment in national planning, it provides for the domestication of multilateral environmental agreements, enhances public participation issue, creates a central environmental information depositary, elaborates access to information principles, establishes an environment fund, creates enforcement orders, provides for both Zambia Environmental Management Authority and members of the public to sue for damages following environmental pollution, and provides for the appointment of honorary Inspectors. In addition to this, the Mines and Minerals Act of 1995 provided, for the first time, a section on environmental management in the mining sector. This section also created the Environmental Protection Fund (for mining), and made it obligatory to undertake environmental impact assessment before mining permits could be issued. The Environmental Protection Fund has now been established, as provided for by the law, and currently has more than USD9.0 million in the account. Secondly, environmental auditing is now being carried out annually on mines around the country, the effect of this has been a significant improvement in the environmental management of mining in Zambia. This paper looks at the response of the Zambian mining sector to these pieces of environmental management legislation, and the direction that the mining sector is expected to take on environmental management going forward."

Jan 1, 2014

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By Evvie Chockalingam

Acid mine drainage (AMD) is a perennial problem particularly in abandoned mines, occurring due to the oxidation of sulphidic mine wastes. AMD is usually characterized by high concentration of dissolved metal ions, sulphate and low pH. The efficacies of substrates such as rice husk and the bark of Eucalyptus tereticornis (Sm.) are assessed for the removal of metal ions such as iron, zinc and copper from acid mine water obtained from an abandoned copper mine. Over 99 % of Fe, 98 % of Zn and 95 % of Cu removal could be achieved from acid mine water, with a concomitant increase in the pH value by three units using rice husk as an adsorbent. With respect to tree bark as an adsor-bent, about 96 % of Fe, 75 % of Zn and 92 % of Cu could be removed from the acid mine water with an attendant increase in the pH value by two units. The free energy of adsorption of the metal ions onto rice husk and tree bark is found to be negative in both the cases, while the adsorption process is endothermic in the case of rice husk and exothermic for tree bark. The adsorption process is found to adhere to the Lagergren pseudo-first order rate equation. The reduction of sulphate con-centration in the acid mine water is achieved using a typical sulphate reducing bacteria namely De-sulfotomaculum nigrificans. Desorption experiments indicate that about 88 % of Zn, 87% of Cu and over 77 % of Fe could be recovered from rice husk and over 70 % of Fe, 82 % of Zn and 77 % of Cu could be desorbed from the metal loaded tree bark using 5 M HCl. The possible mechanisms of metal ion and sulphate removal from acid mine water using rice husk and tree bark are discussed.

Jan 1, 2014

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag's crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By A. S. Chekmarev, T. Z. Lygina, K. G. Egorova, A. V. Skvorcov

"We have conducted analytical and technological evaluation of sepiolite containing clay. The possible areas of application of the sepiolite have been investigated and complex methods of enrichment of natural sepiolite have been identified. It was determined that for preserving the structure of minerals after processing the most effective method of the natural agglomerates disintegration was the soft abrasion of the clay fraction up to 0,5 mm. Disintegration of sepiolite clay along with using high energy-stressed effects on the matrix can deteriorate the rheological properties of clay suspensions and reduce the yield of drilling mud and sorption properties. To improve the quality of clay powders we used combined gravity-modifying method of wet enrichment. After the wet enrichment the yield of drilling mud increased up to 12.7 m3/t, with the addition of MgO up to 20,3 m3/t. It was noted that drilling muds contenting more than 50% of sepiolite are stable in mineralized (salt) waters. Based on the studied activated sepiolite rocks we obtained the effective heat-insulating materials with relatively low thermal conductivity – 0,165 W/m·K, average strength – 7,29 MPa and water absorption-49,0%.INTRODUCTION The modern development of the Russian economy requires the implementation of scientific and technical tasks. The solutions of it involves a radical reduction in energy, heat losses and material consumption of products, rational and efficient using of all types of resources, as well as the using of new types of mineral raw materials and materials based on it. An example of a new type of mineral raw materials for Russia is sepiolite containing rocks, due to unconventional conditions for their soils accumulation in the climate of the Far North. Sepiolite is a unique type of nonmetallic mineral. It is formed in soils, marine and saline basins, occurs in carbonate and carbonate-clay rocks in the form of lenses and lens – shaped layers, rarely nodules, loose powdery masses, shell-like concretions. Sepiolite may have a soft porous macroscopic appearance or less often the structure of the fibrous mass. Color of sepiolite is from white to cream with gray, green, pink and even crimson shade depending on the degree of pollution. Sepiolite can be in two forms - a-sepiolite (parasepiolite), which occurs in the form of large packets of crystalline fibers and ß-sepiolite, which occurs in the form of amorphous aggregates or small flat rounded particles. The sepiolite fibers have a length of from 0.2 to 2 Å, width from 100 to 300 Å, the thickness from 50 to 100 Å (Geological dictionary, 1973)."

Jan 1, 2018

By E. Hulthén

Cone crushers are used in the mineral, mining, and aggregate industry for fragmentation of rock materials. Control systems for cone crusher settings are widely used to compensate for wear and to protect the machines. The eccentric speed in a cone crusher affects the number of compressions the material is exposed to and thus the particle size distribution of the product. Eccentric speed also affects crusher capacity. However, the speed of the crusher is mostly fixed, because speed changes must be made by shifting pulleys, a process which is quite time-consuming. By applying a frequency converter, which has decreased in cost during recent years, it has become possible to adjust the speed continuously. By also applying mass-flow sensors to the process, the crusher can be run optimally to yield the most sellable products in a given moment. Existing systems normally only protect the machine. The sensors can be mass-flow meters, e.g., conveyor-belt scales. To analyze data from the process and calculate the appropriate value for the speed, an algorithm has been developed. The developed algorithm was tested and evolved at a crushing plant for aggregates that produces around 350 kton a year. The algorithm was implemented in a computer that could communicate with the frequency controller, retrieve data from four mass-flow meters, and also interact with the opera-tor. The computer was reachable over the Internet for the researchers at Chalmers and the algorithm was tuned and improved on-line. The result is a crushing stage that consistently and maximally produces the most desirable product. The performance (yield of required products) increased by 4%. As a bonus, the lifetime of the mantles increased 27% on the evaluated crusher.

Jan 1, 2014

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By D. Z. Wang

A red copper plate, discovered in the ruins of Dachengshan in Hebei province, was recognized as a forged one rather than a cast one, which means it was probably made from natural copper during the Longshan Culture period (2200~2208 BC) in the Chinese history. The copperware, found in the Niangniang Tai relics in Wuwei city, Gansu province, contains 99.6% copper and 0.4% Sn, Pb, Sb and Ni, which was guessed to be made during the Qijia Culture about 2000~ 1900 BC in the Chinese history in the late Neolithic before Shang dynasty. This shows that Chinese ancestors were able to distinguish, sort and use some native metals and minerals more than 4000 years ago.

Jan 1, 2014

Calaverite is a gold telluride found in the Kalgoorlie region, Fiji, Cripple Creek Colorado and numerous other locations. It is known that a high pH is necessary for calaverite cyanidation, with the leach rate increasing substantially above pH 12 due to the hydroxide ion concentration. In most circumstances lime is used to achieve high pH, however lime saturates at approximately pH 12, limiting the maximum pH obtainable in a critical region for calaverite leaching. Plant observations, laboratory experiments and thermodynamic modelling show that the maxi-mum hydroxide ion concentration that can be achieved with lime (CaO) is strongly dependent on common ions. The presence of calcium, as commonly found in saline waters, substantially diminishes the maximum pH that can be obtained with lime. Conversely the presence of sulfate ions, as generated through oxidation of sulfides, substantially increases the maximum pH that can be achieved with lime. Sulfide oxidation during cyanide leaching of complex ores may generate acid and sulfate ions, making overdosing with lime at the front of the circuit, or staged addition down the leach train, important to maintaining the maximum hydroxide concentration.

Jan 1, 2014

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By Z. Y. Lan

Bioleaching of marmatite with various mixed cultures of microorganisms was investigated. The experiments were carried out in shaking flasks with iron-free nutrient and the pulp density of 10% wt/vol at the temperature of 30?. The results show that zinc is preferentially leached before iron. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans is 62% in 18 days. The leaching rate of zinc with the mixed culture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans is nearly the same as that with the mixed culture of Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans (45% versus 50%). SEM and EDX analysis of the leaching residues indicate that a solid product layer composed of iron sulfide, elemental sulfur and jarosite accumulates in the mineral surface and becomes a barrier to the dissolution of marmatite. The bioleaching of marmatite follows the shrinking core product layer model. When the product layer increases and becomes insoluble, the leaching rate is controlled by the diffusion through the product layer and slows down. When the product layer decreases or becomes a porous layer, the leaching rate is controlled by chemical reaction and enhanced dramatically.

Jan 1, 2014