Search Documents

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

Jan 1, 1998

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By Hanlong Liu

The construction process and load-bearing behaviors of Cast-in-place Concrete Thin-wall Pipe Piles are analyzed based on its application on Yan-Tong Expressway project. The low strain test, static load test and field excavation are also carried out. It can be concluded that the new type of pile is convenient to construction with high bearing capacity and reliable quality, which has great potential in practical engineering.

Jan 1, 2006

By Lianyang Zhang

For optimal design of rock socketed shafts used to support axial loading, it is important to predict the end bearing capacity. The existing empirical methods for determining the end bearing capacity of rock socketed shafts use the empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of intact rock, sc. Since rock socketed shafts are supported by the rock mass (both intact rock blocks and discontinuities separating them) not just the intact rock, one should consider not only the intact rock properties but also the influence of discontinuities when determining the end bearing capacity. Although the effect of discontinuities may have been implicitly (partially) included in the empirical relations derived from the results of load tests, it is not clear how big the effect is and how much of it has been included. In this paper, a database consisting of 50 test shafts, 25 of which contain the RQD (rock quality designation) value, is developed. Using the database, the applicability of the existing empirical relations is evaluated and two new empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of rock mass, scm, are derived. The new empirical relations explicitly consider the effect of discontinuities by using scm which is directly related to RQD. Finally, an example is presented to demonstrate the application of the newly derived relations.

Jan 1, 2008

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003