Search Documents

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By N. Mejia, Z. Xiao, D. Fragomini, A. R. Laplante

"The adaptation to platinum-group minerals (PGMs) of a protocol developed to predict gold recovery by gravity is presented. The protocol is based on three different data sets: ore characterization of gravity-recoverable minerals, description of their behaviour in cyclones and ball mills, and performance of recovery units. Examples of these are given. It is shown that the gravity-recoverable PGM (GRPGM) content can be very high. A case study at the Clarabelle mill is presented. Sperrylite is the dominant platinum mineral, and its partition curve is very similar to that of gold, despite its lower density. Its grinding kinetics is significantly higher than for gold. As a result, sperrylite accumulates in finer sizes than native gold, but can still be recovered by gravity or flash flotation. Recovery projections based on gravity recoverable data are presented.BACKGROUNDReliable modeling of gold recovery by gravity or flash flotation from a grinding circuit is based on the ability to describe the properties of gold-bearing particles in the ore, their behaviour in grinding and classification units and the performance of the equipment used for recovery, be it gravity or flotation. This is shown in Figure 1."

Jan 1, 2004

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

By David M. R. Stone

Underground mining in the gold industry is gaining popularity in Nevada, and with it the use of cemented rockfill is becoming mainstream. Even with today?s high metal prices, however, mining companies are very sensitive to the margins they realize, and are constantly looking for ways to reduce costs or improve efficiencies. Given that the backfill is one of the largest cost centers in underground mining, mines are constantly under pressure to reduce backfill costs. This paper will present an overview of the factors that impact cemented rockfill quality in Nevada mines based on the authors many years of consulting experience. Cemented rockfill quality can be linked directly to binder consumption, hence programs aimed at improving quality generally result in lower binder costs, better performance in the fill (hence less dilution), and improved safety. The paper will conclude with the key elements of a comprehensive program of backfill quality assessments and backfill QA programs. Comparative laboratory and minesite data from a number of operating and proposed mines will be presented.

May 1, 2007

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By Robert Cluff

The Campo Morado precious-metal-bearing, volcanogenic massive sulphide district occurs in a Lower Cretaceous felsic volcanic sequence in a northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. The deposits belong to a low-sulfidation, volcanogenic massive sulphide system formed in a subaqueous environment, and are of the siliciclastic type. Most are on the flanks of felsic domes or in adjacent basins and many are associated with heterolithic volcaniclastic rocks. The Reforma and possibly the El Rey massive sulphide deposits are interpreted to be overturned, and the Naranjo, El Largo, and Estrella de Oro deposits and the El Profundo occurrence to the south are upright. The G9 deposit and the La Lucha and San Rafael occurrences are in an over-thrust plate further to the southwest. In several of the deposits, zinc, lead, silver, and gold are concentrated near the stratigraphic top, and copper is concentrated near the stratigraphic base; copper also is concentrated in replacement bodies near the top of some domes. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Gold and silver occur in argentian gold, and silver also occurs in tennantite/freibergite and galena. Underlying stockwork zones contain disseminated and vein quartz, pyrite, chlorite, and ankerite, with locally abundant chalcopyrite and/or sphalerite. Exploration since 2004 has enlarged greatly the El Largo and the high-grade G-9 deposits, and slightly enlarged the El Rey deposit. The cumulative in situ massive sulphides for the Reforma, Naranjo, El Rey, El Largo, and G9 deposits exceed 45 Mt.

May 1, 2006

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By C. J. Martin, M. P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist.To date the performance of more than 20 flotation plants has been predicted, including copper, lead, zinc, phosphate, pyrite, graphite, cassiterite, platinum, nickel and various slags. The method has successfully been used to predict and size four flotation plants directly from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted.The technique has now received broad acceptance within the South African mining industry, for example in the last year alone it has been used to drive flowsheet development for at least seven new plants. It is also being used to assist in the optimisation of existing operating plants.The methodology is described in this paper and verification of the methodology is presented using case studies of porphyry, polymetallic and PGM operations.INTRODUCTIONThere is considerable interest these days in the use of modelling to simulate flotation circuits, for process design and plant optimisation purposes. Although these models are proving to be useful tools for plant design and optimisation, their complexity can make them cumbersome – expensive to use and difficult for metallurgists to visualise and mentally absorb, without a background in each specific technique. In “SUPASIM” no attempt is made to measure flotation fundamentals, rather to use empirical relationships between laboratory flotation kinetics and plant performance – relationships that hold up well to validation exercises as will be demonstrated later in this paper. Although not designed to be as comprehensive as other models, “SUPASIM” is easily understood by the operating metallurgist and can be quickly and easily applied."

Jan 1, 2004

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989