Search Documents

By He Zhexiang

The settlement properties of tailings modified by flocculants were investigated at the Shizhuyuan Mine, with the aims to screen for the most effective flocculants and the optimum dosage rates for tailings sedimentation. The settlement rate was used as the indicator of effective tailings sedimentation. Calcareousness and three polyacrylamides (F1, F2 and F3) were selected for settlement property evaluation. The results proved that sole use of calcareousness or any of the polyacrylamides had no apparent effect on the tailings sedimentation, while a remarkable acceleration of sedimentation could be observed with a combined addition of calcareousness and polyacrylamides, among which the addition of polyacrylamide F2 together with calcareousness is the most effective. The optimum dosage rate of F2 and calcareousness is 50g/t and 3kg/t respectively. The density of tailings slurry has an effect on sedimentation at the early settlement stage, with lower density generating quicker initial settlement.

May 1, 2007

By S. Parada, P. T. Jones, M. Guo, S. Smets, E. Boydens

The corrosion behaviour of a pitch-bonded MgO-C refractory in contact with a vacuum oxygen decarburisation slag with high Al2O3 content (12-17 wt%) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterisation of the corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature, corrosion time and the Al2O3 content in the slag is discussed. The degradation mechanisms include slag infiltration, direct MgO dissolution from the refractories into the penetrated slag, erosion of magnesia grains at elevated temperatures, removal of carbon through the MgO-C reaction, and finally, oxidation of refractory carbon by reducible slag components. Both a porous MgO layer and a dense (Mg)(A1,Cr)2O4 spinel at the slag/brick interface were observed. Their formation mechanisms and industrial relevance are discussed.

Jan 1, 2004

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By Lastram Rolando, Larry J. Hulbert, Louis J. Cabri, J. H. Gille Laflamme, John L. Campbell, Soey H. Sib, Chris G. Ryan

"The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fine-grained minerals which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700/0 of the major Ni carriers and 78% of the major Cu qurier will be liberated at a grind of 80% -U,.7 ,an (-500 mesh) for typical low-grade gabbro (West zone, sample No.1). For typical ""clinopyroxenite"" (West zone, sample No.2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3) the liberation would be 71% and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total 24.5% for typical low-grade gabbro (West zone, sample No. I), 15% for typical ""clinopyroxenite"" (West zone, sample No.2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No.3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fine grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as some would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No.2 and No.3 is closely associated with magnetite. Palladium occurs in diverse ways. It occurs in the form of several Pd minerals (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tellurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chalcopyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerals and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate.However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No.2 and No.3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No.3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No.3, in order to improve Pt and Pd recoveries. Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefined Re-Ir-Qs..Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By J. Donnelly, A. V. Deev

Substitution of coal and coke by renewable carbon (charcoal) is a low-risk and low-capital path to 50% or more reduction in net CO2 emissions by the steel industry. However, the high cost of charcoal and its low availability in most countries are barriers for the implementation of this approach. Development of an efficient wood carbonisation technology (slow pyrolysis) capable of producing large-volumes of charcoal from low-cost wood feed (e.g. wood wastes or forest residues) is an essential step towards the use of renewable carbon by the iron and steel industry. This paper provides a summary of the progress made over several years of R&D covering: (1) development and piloting of a new energy efficient slow pyrolysis process for production of charcoal from woody biomass at a competitive cost to the PCI coal, (2) techno-economic evaluation of the process. The main feature of the process is that the material undergoing pyrolysis is heated spontaneously without the supply of heat or air to the reactor. This makes it possible to carbonize large volumes of small-sized wood (e.g. wastes and residues) in a single reactor unit and capture high calorific value pyrolysis by-products

Jan 1, 2015

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By F. Mackay, S. A. B. da Fontoura

"The theoretical solution for a viscoelastic well was presented by Gnirk and Johnson in 1964. From this an exercise was executed to validate the numerical simulation of a cemented salt well. The exercise comprised the geomechanical behavior through time of a cemented salt well, this was achieved using a finite element commercial software. This simulation showed the accuracy of the theoretical solution for viscoelastic materials such as salt rock. The theoretical solution presented elastic and viscoelastic analytic equations for the tangential and radial stresses. The equations for the elastic material (casing and cement) and for the viscoelastic material (salt rock) are presented here: Where equations 1a & 1b are the radial and tangential stresses of the elastic material; equations 2a & 2b are the radial and tangential stresses of the viscoelastic material; and a, r and b are the geometrical parameters explained in Figure 1. These equations are function of Pb, a stress time dependent factor that comes from the Burgers model of viscoelasticity. This is well explained in Gnirk and Johnson (1964) and for the sake of simplicity is not disclosed here. Po is the stress at section A-A’ dependent of the depth h."

Jan 1, 2015

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By I. Raheb, M. Y. Debili

"A set of Al-Co binary alloys (with respectively in weight percent 10%, 20%, 30%, 40%, 50% and 60% Co) have been studied by X-ray diffraction at the as compacted state. The structural evolution according to cobalt addition shows special features as the apparition of fcc cobalt and hcp cobalt beside aluminium in some cobalt compositions of the Al-Co mixtures using only cold compaction without sintering at high temperature. Figure 1 Cobalt is not a common alloying element in aluminium because its solubility is very low [1]. According to the pressure-temperature phase diagram, Co is known to exist in two allotropic forms: a low-temperature hcp phase and a high-temperature fcc phase [2-3]. At room temperature, Co is stable in the hcp form but it transforms to the fcc form when it is heated to above the transition temperature 695K. Powder aluminium and cobalt (99.999 %) were used in the proportions defined according to the required compositions. The total mass of the samples to be elaborated was between 8 g and 10 g. Cold compaction of mixed powder (Al-Co) under an uniaxial load of 10 MPa has been achieved to obtain a dense product (60%)."

Jan 1, 2015

By A. B. Luz, A. Middea

Kaolin clay is heavily used in the paper industry as a coating and a filler, however to attend the specifications required by the industry it has to be processed. Kaolin is also used as a filler and pigment in various materials, such as paint, plastic, rubber etc. Some crude kaolins as mined in Northern Brazil, contain colored impurities such as iron oxide and rutile/anatase. These minerals normally are stained by iron and as a result vary from yellow to dark brown in color. The kaolin beneficiation process used in that region consists mainly of degritting, fractionation by centrifuge, high gradient magnetic separation, bleaching with sodium dithionite, filtering and drying. In some kaolin clays from that region, titanium oxide mineral occurs in fine fraction, lower than 2 µm, and so making the industrial process more difficult. The conventional method of classification and bleaching with sodium dithionite, markedly improves kaolin brightness, but has little effect on anatase removal. In fact, the fine fractions resulting from centrifugation, in many cases contain more TiO2 minerals than the original whole clay or the coarse fraction. The present work is related to purification of Brasilian kaolin clay using selective flocculation for removing its colored impurities such as rutile and anatase. This study was conducted in bench scale and it consisted of: blunging, screening, conditioning and decantation. Overflow and underflow resulting from settling of the flocculated material were then dried and submitted to TiO2 and brightness analyses. Sodium polyacrylate and sodium silicate were added to kaolin clay suspension as dispersant and ammonium hydroxide was also added to adjust pH. After degritting, the minus 44 µm fraction was conditioned with hydroxamate surfactant and then polymers of different anionic charge were added. The influence of pH and type of polymer on efficiency of TiO2 removal, as well as kaolin mass recovery were studied. The results obtained in the present study are quite promising. It was possible to diminish TiO2 content and increase kaolin brightness (ISO) from 82 to 88%.

Jan 1, 2004

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By R. A. Sullivan

I T IS one of the unwritten policies at Preston Mines that we examine closely any method or tool that will help us in our constant battle against rising costs. It is our personal conviction that most work methods can be improved. Therefore even though the job went well yesterday, it does not necessarily follow that it should be done by the same method today. With the arrival of the natural gas pipe line in the Porcupine area it was obvious that we would have to take a good look at the possibilities of using this source of fuel for plant heating. • Steam presently generated at Preston is for heating purposes only, no process steam being required. Prior to the fall of 1960, the heating plant consisted of two low pressure, coal-fired, fire-tube boilers, operating at an approximate pressure of 14 pounds per square inch. These boilers were underfed by stokers and could be operated either singly or together. ~o. 1 unit was a horizontal return tubular boiler, registered at 100 h.p. No. 2 unit was a fire-box boiler, registered at 75 h.p.

Jan 1, 1962

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952