Search Documents

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By S. Hobo, M. Yagisawa, T. Uchida, C. Tokoro, T. Kato

In this study, quantitative modeling was carried out for the treatment of simulated waste water containing As(V), Zn(II) and Hg(II) as toxic elements, and Fe(III), Na(I) and sulfate as coaxing ions. The objective was to predict the pH and residual concentrations of all the elements in solution after the neutralization/co-precipitation treatment. To accomplish this, the removal mechanism for As(V) and Hg(II) by ferrihydrite precipitation was first investigated for simulated waste water containing only As(V) or Hg(II). From the experimental results, it was confirmed that the removal mechanism involves not only surface complexation but also surface precipitation. However, surface complexation is the main mechanism for As(V) and Hg(II) removal to meet the target levels regulated in Japan. Next, the surface complexation model was constructed for the removal of As(V) and Hg(II) by ferrihydrite. The specific surface area and site density were determined from reference values proposed by Dzombak and Morel (1990). By comparing the experimental and calculated results, it was confirmed that our constructed model could successfully represent the experimental results. Furthermore, the surface complexation model was coupled with chemical equilibrium calculations and applied to the neutralization of simulated waste water containing As(V), Hg(II), Zn(II), Na(I), Fe(III) and sulfate. The constructed model could successfully represent the pH edge for As(V), Hg(II), Zn(II), Fe(III) and SO42- removal. In addition, the constructed model could represent the ion balance. Thus, our constructed model is useful to estimate the amount of neutralizer that is needed to achieve a target pH.

Jan 1, 2016

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Gerhard Heinrich

"The composition and the possible utilization of a slag sample from a nickel smelter operation in the Sudbury district were investigated. The sample containing 0.136% Ni, 0.10% Co and 0.29% Cu could be characterized as a fayalit e slag with a sulphide bearing glass matrix. While the fayalite contains most of the Co, Ni is enriched within both sulphides and fayalite. Cu is only present in higher amounts in sulphides or metallic droplets. This, as well as the small grain sizes of the mineral phases, inhibits significant enrichment by mechanical methods. However preconcentration is possible by means of magnetic separation. An effective hydro metallurgical approach proved to be oxygen pressure leaching with sulphuric acid. Accordingly, the method proposed for processing the investigated slags is to combine the normal utilization as coarse construction material with pressure leaching of the fines and the ground upgraded magnetic fraction. Besides the recovery of base metals, the leaching process yields fine-grained residues, which, after addition of CaD, will set to a cement-like material, or can be used as a pozzolanic cement colour. INTRODUCTIONDuring the pyro metallurgical processing of nickel ores, the valuable metals nickel, cobalt and copper are enriched within the sulphide matte, similar to the smelting of copper ores. The resulting waste materials are slags, which may still contain valuable metal contents of up to 0.5% or above . These contents are close to the cut-off grades of some nickel-cop per-cobalt deposits. The methods that are used to recover copper from slags comprise in general further pyro metallurgical treatment, often after enrichment by flotation. Another area of application for such slags is their use as construction material. However, this might cause environmental problems if nickel containing dusts are produced.Based on one example, the characerization and a possible way of complete utilization of nickel smelter slag s as construction materials in combination with partial base metal recovery are described in this paper. The investigated slag sample was obtained from a dump site in the Sudbury district, Ontario. Detailed test series for process optimization were not possible during this study due to the limited available sample size."

Jan 1, 1989

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By Roger C. Parsons

"The problems presented by ice formation and interference with processes, structures and mechanical operations in the mining industry can be expected to increase sharply as more of our mineraI needs are supplied from the far north. A process of rapid ice destruction is presented which lends itself to the effective removal or penetration of ice. Suggestions are offered for applying the system to problems related to mining activity in cold environments. The system can be readily adapted to large-scale operation, the reactant components being transported in crystalline form and volatilized on site.IntroductionThe number of operational mines in northern environments, relative to the number of mines in the temperate zone, will increase in the years ahead. This is not surprising, because:(a) in the past, those mines closest to centres of commerce had minimum transport charges and hence were more economic to develop;(b) great centres of commerce were far removed from northern environments;(c) the exhaustion of ores and lowering of grades in temperate zones now offset to some degree the extra transport costs applied to northern ores;(d) the abundance of excess energy in the north in the form of oil, gas and hydropower attracts mining as a means to justify its development; (e) assuming that the frequency of mineral occurrence north of the 52° N latitude is no different than south of it, there are many deposits waiting to be developed.As a result of current and projected activity in northern environments, we are faced today, and will be increasingly so in the future, with mining problems rarely encountered before-problems related to below-freezing temperatures. Engineering activity in permafrost regions will increase as new mining ventures are developed north of the 52° N latitude, roughly coinciding with the -1.1 ° C isotherm in Labrador, the upper temperature boundary for permafrost."

Jan 1, 1982

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By R. A. Walker, G. Scheltgen, T. Javorsky, G. Blackwell

"Recent engineering advances in open pit rock mechanics have resulted in improved pit wall slope design and improved operating procedures in the event of a major wall instability. At the other end of the spectrum, on the scale of single bench failures, considerable discretion is left to the mine operators as to how potential problems are handled. The usual alternatives are either to operate with caution beneath potential hazards, or try to bring the unstable rock down. In specific cases it may be advantageous to attempt to stabilize rock structures for reasons of access and operating safety.A t the Brenda Mines open pit a prominent structure on the north wall had caused recurring bench-scale wedge failures when exposed on each mining level. In spite of operating precautions a shovel was hit by a rockfall causing significant damage. The first section of this paper describes the investigative, design, and stabilization methods which permitted subsequent mining beneath the structure to proceed without incident. Emphasis is placed on the personnel and equipment resources available at the mine site which were used to minimize costs and which would be available at most operating mines.The second section describes an ongoing research project that utilizes radio telemetry to transmit slope monitoring data. As part of this project the wedge structure was instrumented so that it could be continuously monitored with the aid of a computer. The application demonstrated the potential of 'micro- chip' technology to remote data collection and processing as related to rock structure monitoring, slope stability and safety."

Jan 1, 1989

By Peter N. Calder, Louise H. Michaud

"An interactive mine planning package has been developed to aid with the tasks involved in generating dragline mine plans. This package employs recent advances in PC-based,3D computer graphics and 3D geologic modelling. A Gridded Seam Model (GSM), capable of modelling rugged topography and multiple coal seams, including folding and faulting, is used to generate the geologic database This model is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal reserves and the removal of waste material.As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans and can allow for the evaluation of a number of mining options within a reasonable time frame.IntroductionThere are a large number of variables that must be taken into account during the development of a dragline mine plan. This is especially true when developing a mine in mountainous terrain, where there is a lack of continuity of the geology and topography over the mine site. Until recently, the complexity of dragline mine plans has prohibited the development of a universal mine planning package that is applicable to all geologic and topographic situations. The majority of the commercial programs that are presently available to facilitate dragline mine planning have been developed for specific mine properties or are limited in the coal geology and mining methods that they can simulate (Brown and Clifford, 1983; White 1983; White and Jones, 1984; Sadri and Lee, 1982; Dagdelen, 1979)."

Jan 1, 1993

By I. R. Muirhead

"One approach to making new technology available is to demonstrate its value under full-scale operating conditions. Studies were undertaken to assess the feasibility of this approach to introducing a longwall mining system to the western Canadian coalfields.The longwall method of mining coal is described, world and Canadian usage is reviewed, and the merits of the system in comparison 10 other coal mining methods are discussed.The rationale for a longwall demonstration in western Canada is presented, along with a proposed organization for the design, operation and dissemination of the findings from such a trial. The factors which must be considered in the design of the demonstration, and in the assessment of a potential site are highlighted. It is concluded that a demonstration of this technology is both timely and essential to prepare the way for the western Canadian coal industry of future prospects for coal.IntroductionFor many years CANMET has encouraged research work organized on a cooperative basis. This requires that a working consensus must be negotiated by researchers and operators at the beginning of the project and continuously refined as work proceeds. The result is usually a more relevant selection of research problems, improved direct ion and con duct of experiment al work and often a validation phase in which research concepts are tested in an opera ting environment. All this tends to narrow the gap between obtaining research results and applying them.Even under the best of circumstances cooperative projects require a good deal of coordination and enthusiasm to maintain focus and the pace of work. The working perspective of a research scientist in a government laboratory is substantially different from that of a mine operator at a producing mine, and a common ground must be found. This is difficult to do and cooperative projects typically evolve over several years as experimental results progressively define the potential solutions to mining problems."

Jan 1, 1985

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally ' fits ' within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer 'cheap' commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By Ludwig Strah

"The paper outlines the history of rubber mill liners beginning with the awarding of the first North American patent rights in 1923. It includes the early-day applications and installations of the 1920s and 1930s through to their present-day application. Over-all rubber mill liner design is discussed in relation to present day installations employing rubber mill liners in various grinding applications. A brief overview is given of a manufacturer's procedures to produce rubber mill liners.IntroductionIn early 1910, it became apparent that the productive life of the silver mines in Cobalt, Ontario, could be substantially prolonged by mining lower-grade ores.The mining of lower-grade ores required the establishment of treatment facilities which initially employed jaw crushers, stamp mills, jigs and concentrating tables. The recovery of silver in other than a coarse metallic form required the additional step which was introduced at that time: the cyanidation of silver concentrates from the tables. The resultant requirement for increased and improved recovery led to the introduction of grinding mills, i.e. tube mills.Shortly after the introduction of the tube mills to the Nipissing Mine's mill in 1914, the idea of using rubber as a mill liner material was spawned. However, no action was taken due to the advent of World War I. It is interesting to note that the idea of rubber mill liners emanated from having used pieces of solid rubber tire as an emergency repair on a set of liners when a liner had broken and no immediately available spare was on site.The credit for this ingenuity and subsequent application for a patent on rubber mill liners falls to James John Denny, the mill superintendent, and Rolla Barnum Watson, the general manager of Coniagas Mines Limited. The patent application was formally made on December 3, 1921. The U.S. Patent Office issued Patent No. 1,470,597 on October 16, 1923."

Jan 1, 1982

By Louise Corriveau

A Targeted Geoscience Initiative transect in the eastern Grenville Province reveals an extensive VHMS-style cupriferous hydrothermal system among rhyolitic pyroclastic rocks of the Wakeham Group at La Romaine, Québec. The volcanic rocks outcrop sporadically along a < 10 km-wide by about 100 km-long belt correlated with the south-eastern extension of the Wakeham Group. This belt occurs among voluminous, magnetite-bearing, granitic gneiss. At Lake Musquaro, 1.51 Ga metarhyolitic to dacitic lapillistones and flows, locally with aluminous nodules and veins, are intruded by 1.49 Ga feldspar porphyries. This volcanic package was deposited on typical Wakeham Group arenite (< 1.52 Ga) interbedded with nodular, muscovite- and fibrolite-bearing gneiss, and minor marble hosting finely layered garnetiferous hornblendite, garnetite and magnetite-bearing coticule. The latter are interpreted as meta-exhalite and with the associated albitite (sodic alteration), aluminous veins (hydrothermal leaching) and magnetite-rich granitoids, they are key elements in the search for concealed mineral deposits in this area. At La Romaine, to the south, 1.5 Ga lapillistones outcrop structurally above metasediments and below a composite amphibolite unit of uncertain origin (lava or sills) with magnetite-rich (BIF?) units. An extensive zone of aluminous gneiss, with lapilli textures, provide evidences for severe hydrothermal leaching of the volcanic rocks prior to metamorphism. An adjacent siliceous vein-textured unit likely represent a zone of intense silicification (74 wt.% SiO2), while aluminous, hematite to magnetite-bearing veins in adjacent felsic gneiss (tuff?) preserve evidences for the sequence of alteration events. Despite granulite-facies metamorphism, the main characteristics of the amphibolite unit persist along the entire belt. This competent unit likely served as a cap rock; the garnetite, diopsidite and hornblendite it hosts provide effective guides to the sites of fluid discharge and mineralization. A number of Cu showings, modest in size, were discovered in this unit. Their systematic occurrence, in a structural-stratigraphic sense, indicates that this setting is attractive for mineral exploration despite high-grade metamorphism and deformation. Late-stage veins laden with fluorite crosscut these alteration zones, and are themselves metamorphosed, indicating that hydrothermal activity was polyphased. SHRIMP U-Pb ages obtained on detrital zircons (1 arenite) and on igneous zircons (5 volcanic rocks, 1 porphyry and 6 granitoids), pervasive arc-type geochemical signatures and presence of in situ rafts of barium-rich garnetite in the granitoids indicate that sedimentation and volcanism occurred between 1.52 and 1.49 Ga coevally with hydrothermal activity and emplacement of a sub-volcanic 1.5 Ga granitic batholith with early, 1.53 Ga tonalite intrusion. Such a geological context can sustain large-scale hydrothermal cells and development of VHMS, Cu-Fe oxides or SEDEX deposits.

May 1, 2003