Search Documents

By W. H. Bassett, C. H. Davis

In the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-mm.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystal-lization of cold-worked alpha brass on annealing,l Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work. The first alloy was taken from regular mill stock that had been rolled from 0.580 in. to 0.376 in. (14.7 mm. to 9.5 mm.) gage, a reduction of 35.1 per cent. This bar (No. 1) had the following composition: Copper, 69.20 per cent.; zinc, 30.76 per cent.; lead, 0.02 per cent.; iron, 0.02 per cent. The second alloy was also taken from mill stock of 0.325 in. (8.25 mm.) gage and was rolled as shown in Table 1, in order to get four bars reduced two, four, six, and eight B. & 5. numbers respectively. This second alloy

Jan 1, 1919

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By F. Petkovich, M. P. Sudbury

Development of a new method of treating flotation concentrates for the preparation of feed suitable for direct charging to blast furnaces or converters is described. The method takes advantage of the fact that pyrrhotite contained in the concentrates can be made to undergo exothermic reactions which, under properly controlled conditions, result information of oxidation products that serve to cement the concentrate particles together. Thus green concentrates either in the form of pellets or briquettes containing 5 to 8 pct moisture not only were hardened, but also completely dried autogenously by continuous countercu,vrent shaft treatment with air. The process was developed through pilot plant operations ranging from 35 1b per hr to 2.5 tph, culminating in products evaluation tests on a railway-car scale. Falconbridge Nickel Mines Ltd., Falconbridge, Ont., have practised sintering, on a travelling grate machine, for many years to prepare a pyr-rhotite-bearing Cu-Ni sulfide flotation concentrate for blast furnace smelting. In recent years the development of new mines, and the construction of concentration plants some 40 miles from the smelter has increased the quantity of concentrate shipped, and encouraged the search for a method of producing dry, hard pellets or briquettes suitable for direct charging to a blast furnace or converter, and capable of withstanding considerable handling. The cementing properties of pyrrhotite oxidation products were discovered during a search for a suitable agglomeration method for sulfide concentrates, and were exploited in a process subsequently developed for autogenously drying and hardening pellets and briquettes of pyrrhotite-bearing Cu-Ni sulfide flotation concentrate. EARLY TEST WORK The production of hard, dry pellets of concentrate filter cake was attempted in the drying plant of one of the new concentrators. While soft pellets were produced containing 5 pct moisture, attempts at further drying resulted in disintegration of the pellets and intolerable dusting. The plant therefore was controlled to produce a concentrate containing about 6 pct moisture. The partially dried concentrate, which was shipped to Falconbridge for sintering, tended to heat spontaneously in transit. An at- tempt to briquette the moist concentrate at Falconbridge, in a plant incorporating a muller, a 20-in. roll briquetting press, and a steam-heated travelling grate oven, was more successful, although the equipment corroded rapidly due to the acid nature of the concentrate after spontaneous heating had occurred. LABORATORY STUDIES OF SPONTANEOUS HEATING OF CONCENTRATE The spontaneous heating of partially dried concentrate was studied in the laboratory. Moist concen-

Jan 1, 1961

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By J. F. Butler, H. W. Paxton

The vapor pressures of manganese in equilibrium with several alloys in the iron-manganese-carbon system between 1200° and 1275°K have been measured using the Knudsen effusion technique in conjunction with a vacuum microbalance. The effect of orifice area of the effusion cell upon the measured pressure has been determined. The binary iron-manganese system shows small negative departures from ideality, and the system of mixed carbides, (Fe, Mn)7C3, in equilibrium with graphite behaves ideally. THIS work is a continuation of the investigations in which the Knudsen effusion method has been used to determine thermodynamic activities in systems and at temperatures of interest to metallurgists. In a previous publication,' the free energy of formation of Mn7C3 was determined and some preliminary work on the solution behavior of this carbide with the hypothetical "Fe7C3" was reported. The present work deals with this latter topic and also includes data on the binary ir-on-manganese system. EXPERIMENTAL METHOD The Knudsen effusion method was used to measure the vapor pressure of manganese in both the alloy and carbide sections of this investigation. This dynamic method of vapor pressure measurement presents a problem when studying solid alloy systems in which one of the components has a much larger vapor pressure than the others. Over-all depletion of the alloy in the most volatile component will occur during evaporation so that the pressure of that component will decrease. Even more serious than the over-all concentration change is the surface depletion of volatile component in the alloy brought about by the slow rate of diffusion of this component from the interior to the surface of the solid particle. Since knowledge of this surface composition is necessary in order to relate it to the activity determined through the measurements, changes in surface composition from the analyzed bulk composition are to be avoided in dynamic vapor pressure studies of solid alloys. The system under investigation in this study presents the problem of surface depletion of manganese since its pressure at 1230°K is 105greater than iron and 1020 greater than carbon. Since the existence of a volatile manganese carbide had been ruled out previously,' the high manganese pressure relative to iron and carbon insured that the only species leaving the effusion cell was manganese. Therefore, the effusing species required no analysis so that the manganese pressure was determined directly from the weight loss of the effusion cell. In order to detect small weight losses near the beginning of effusion, a vacuum microbalance was used to weigh the cell continually. These initial weight loss data allowed the rate of manganese effusion to be determined before the surface of the alloy became depleted in manganese. The apparatus used in this investigation is shown in Fig. 1. Temperature was measured using chro-

Jan 1, 1962

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By J. H. Swisher

An experimental study has been made of the possible mechanisms for foam stability in the system CaO-SiO2-Cr2O3, where Cr2O3is the foaming agent. The degree of lowering of surface tension by Cr2O3 was determined at 1600 "C for high -silica melts. Measurements were also made of foam stability under standardized conditions. The results of the two sets of measurements then were correlated by applying the Gibbs and Marangoni theories of film elasticity. It was demonstrated that the Marangoni elasticity effect is probably the largest single contributor to foam stability, although the high uiscosity of' silicate melts makes some contribution in controlling the rate of drainage of liquid from bubble lamellae. ThE tendency of metallurgical slags to foam has frequently been observed during steel-refining operations. In the open-hearth furnace,this tendency is considered undesirable because it slows down the rate of heat transfer from the burners to the molten-metal bath. On the other hand, it is sometimes desirable to have a "foamy" slag in the basic oxygen converter.' A more effective blanket over the steel bath is made by a "foamy" slag, and loss in yield of metal due to splashing is minimized. In addition, a flush slag can be removed more easily in this condition. Since slag-foaming problems in the field have been attacked largely on an empirical basis, it appeared desirable to obtain a better basic understanding of the mechanism of foam stability. The experimental work was directed almost entirely toward the behavior of Cr2O3 as the foaming agent in CaO-SiO,-Cr2O3 melts. In the first stage of the investigation, the degree of lowering of surface tension by Cr2O3 was determined at 1600°C. The second stage consisted of measuring foam stabilities under standardized conditions. The two sets of experimental results then were correlated by applying various theories of foam stability. For convenience in interpreting the surface-tension and foam-stability results reported here, a portion of the CaO-SiO2-Cr2O3 phase diagram2 is reproduced in Fig. 1. EXPERIMENTAL 1) Surface-Tension Measurements. Very little information is available in the literature on the lowering of surface tension of slags by foaming agents. Kozakevitch 3 mentioned that the addition of 1.5 pct Cr2O3 lowered the surface tension of FeO slightly. In another system, some data on the lowering of surface tension of foaming slags by P2O5 were reported by Cooper and Kitchener.4 The technique used for the surface-tension measurements was the maximum bubble-pressure method,' using a single tube immersed to various depths in the melt. This method has been used extensively in high-temperature systems, such as in liquid metals, slags, and glasses.6,7 It has the advantage that the contact angle between the liquid and the tube material need not be known. The equation used for calculating surface-tension values from maximum bubble-pressure measurements is the Schroedinger equatioq5 which can be written as follows:

Jan 1, 1964

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

By A Guinier

RECIPITATION in alloys is undoubtedly one of the most essential phase transformations in metallurgy and, besides, it is a phenomenon of great interest to physicists. It seems then that it can be chosen as a topic for an Annual IMD Lecture. Of course, the subject is a very wide one and I shall discuss here only a very restricted part of it. I should like to show why it is now considered that there is, at the beginning of the process, a stage distinct from the real precipitation, which is the pre-precipitation. We shall be chiefly interested in the atomic structure of the metal in this preprecipi-tation stage. Numerous reviews on this subject have been published recently.', ' The latest was given by H. K. Hardyh t the last meeting of the Institute of Metals in London. One of the most complete articles has been written by the late Dr. Geisler." I should like, at the beginning of this lecture, to pay a tribute to the memory of our friend Arthur Geisler. Some of the ideas which will be developed here are different from those advocated by him. But everybody knows the considerable progress in experiment and in theory which we owe to him and, personally, I deeply feel how fruitful have been the long discussions which we have had during many years. Experimental Basis of the Precipitation Problems Let us recall the essential facts pertaining to the problem of the precipitation. The starting point and the final one are well known. The initial stage is the supersaturated solid solution before quenching. The dissolved atoms replace some of the atoms of the solvent at the points of a definite lattice. It is generally considered that the distribution of the atoms is completely random, and that the lattice distortions are relatively weak. These assumptions are only an approximation. It has now beenproven", that, in some cases, the dissolved atoms have a tendency to segregate to form very small nuclei. These fluctuations of composition are greater than the normal statistical fluctuations in a purely random alloy. We shall see the role played by these nuclei later. The final state is obtained by a very long annealing at such a temperature that an equilibrium is reached in a reasonable time. The alloy is then composed of a matrix which is a saturated solid solution, much poorer than the initial one. Imbedded

Jan 1, 1957

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969