Search Documents

By J. W. Thompson

BURYING DEAD MINERS. BURYING BODIES OF DEAD MINERS. REVISED STATUTES (HURD) 1874, P. 263. SEC. 22. LIABILITY OF RAILROADS, ETC., FOR BURIAL EXPENSES.-When any railroad company, stage or any steamboat, propeller, or other vessel engaged in whole or in part in carrying passengers for hire, brings the dead body of any person into this State, or any person dies upon any railroad car or in such stage, steamboat, propeller or other vessel in this State, or any person is killed by cars, or machinery of any railroad company or by accident thereto or by accident to or upon any such stage, steamboat, propeller, or other vessel, or by accident to or in or about any mine, mill or manufactory,* the company or person owning or operating such cars, inachinery, stage, steamboat, propeller, or other vessel, mine, mill or manufactory shall be liable to pay the expenses of the coroner's inquest upon and burial of the deceased and the same may be recovered in the name of the County in any court of competent Jurisdiction. NOTE--The original Act of February 15, 1855 (Laws 1855, p. 170), makes no reference to the dead bodies of persons killed" by accident to, in or about any mine."

Jan 1, 1919

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

Safety remains a critical priority for the Australian mineral resource industry and will receive increased focus in the future. This is particularly evident in underground coal mines where reserves are becoming deeper and more hazardous to extract. The CSIRO, through its Exploration and Mining Division, have recently delivered on two projects aimed at providing step-change capabilities in real-time risk management and hazard control. This paper describes the key outcomes of these projects.

Jan 1, 2005

There are available today many various types of mixing systems, tank types and process liquors confronting the process designer of gold adsorption circuits. This short paper is to give the process designer an insight into the special mixing requirements for resin-in-leach and resin-in-pulp, plus the advantages and disadvantages of the various mixing systems that are available to agitate the required tank shapes. An understanding of the latest developments in this important process area of gold production is addressed and information given on the results of resin degradation in various tank sizes over long periods of mechanical agitation.

Jan 1, 2007

By R Moreby

This paper is a demonstration of the techniques developed during an Australian Coal Association Research Program (ACARP) funded research project aimed to develop aids, principally computer based, to assist mine personnel to more efficiently manage significant incidents in coal mines. These aids include software to aid in the location of the incident, electronic information storage and retrieval, online site emergency response manuals and software to aid in decision-making.

Jan 1, 2005

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By Donald B. Lindsay

This report presents the findings of an investigation into the characteristics of a number of techniques for cleaning ambient air with special emphasis on their applicability to the removal of the short-lived radioactive decay products of 222-radon, the so-called " radon daughters" that have been identified with the induction of lung cancer in underground uranium miners. The purpose of the study was to review the requirements for control of radon daughter concentrations in mine air, and to examine all techniques whose feasibility has been demonstrated in principle and which in our judgment would be capable of meeting those requirements. The study has included a review of all pertinent literature, both technical and proprietary, on the subject of the control of miner exposure to the radon daughters and in the area of potentially applicable air cleaning technology. Information about the nature of the problem and about the experience of the uranium mining industry in applying air cleaning methods to its solution was obtained by visiting mines where such methods are in use, and by written correspondence and telephone conversations with other industry sources. Information on performance characteristics and costs of applicable air cleaning methods and equipment was obtained from the experience of our own engineering staff and by visits, interviews, and correspondence with manufacturers of industrial air cleaning equipment.

Jan 1, 1978

By A. Timur

Fluid flow properties of porous media have long been of interest in such varied disciplines as geology, geophysics, soil mechanics, and chemical, civil, and mechanical engineering. This interest has resulted in numerous models of porous media that have been proposed, tested, and found to be useful under, at best, only special circumstances. A critical review of most of these models is given by Scheidegger. 1 The application of each new tool to the study of porous media has helped to test some of the existing theories and to form new ideas based on the new parameters being measured. In the application of nuclear magnetic resonance (NMR) techniques to the study of the properties of fluids in porous media, the theoretical studies of Korringa et al.2 resulted in a model for the relaxation of spin polarization of protons in a hydrogenous fluid in a pore of a solid. Seevers3,4 verified this model, established a method for measuring the surface-to-volume-ratio distribution in a porous medium, and proposed a technique for determining specific permeability in sandstones. In the present investigation, the uses of NMR methods are extended and a simple model of porous media is developed from an analysis of pulsed NMR measurements. In this model, the pore spaces of a porous medium are divided into three groups on the basis of their surface-to-volume ratios. To evaluate predictions of the NMR model, laboratory measurements of spin-lattice relaxation time, porosity, permeability, and residual (irreducible) water saturation were conducted on more than 150 sandstone samples obtained from four oil fields in North America. Applications are discussed for estimating the volume of movable fluid, ?p, and the specific permeability, k, of sandstone samples. The former parameter, which can be considered as producible porosity, is expressed by ?p = [1 -- (Swr/100)]? , .... (1) where + is porosity in percent of bulk volume and Swr is the residual (irreducible) water saturation in percent of pore volume at a capillary pressure of 50 Psi. Fast, nondestructive laboratory methods are described for determining porosity, movable fluid, and permeability of sandstone samples from measurements with a pulsed NMR (spin-echo) apparatus. Procedures are given for adapting these methods to samples of irregular shape and small size. Theory General In the Korringa, Seevers, and Torrey2 (KST) model the observed decrease in the spin-lattice relaxation time, T1, of protons of a hydrogenous liquid contained in the pore spaces of a porous solid is attributed to an increase in the correlation time for the random motion of the water molecules and to the presence of paramagnetic centers at the liquid-solid interface. This KST model predicts the observed relaxation time of a hydrogenous liquid in a pore of a solid through

Jan 1, 1970

By W. W. Agey

As a part of the program of investigation of domestic sources of manganese in the western United States, engineers of the Bureau of Mines examined. and obtained samples of ore from two properties in the vicinity of Barstow, San Bernardino County, Calif. In addition to these, samples from two other properties in the same vicinity were submitted by the owners. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration by ore dressing. The Big Reef manganese claims axe about 140 miles east of Barstow, Calif. The claims were leased by W., E. Thurber of San Gabriel, Calif., from the owner, C. S. VanDoren of Daggett., Calif. Manganese oxides occur as a replacement deposit in heavily brecciated andesite along a fault plane. Four samples were taken by an examining engineer of the Bureau of Mines from the ore zone, which, when composited, were representative of all the exposed ore. Preliminary tests were made on lot B, and final tests wore made on the composite sample. The Trans-Oceanic property is about 20 miles southeast of Barstow, near Newberry, in the. Pisgah mining district, Calif. The sample, submitted by the owners, was taken from a 1,000-ton reject clump from a hand-sorting operation. The ore occurs as a replacement of rhyolite.

Jan 1, 1952

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants. On account of extensive folding and faulting of the coal measures, mining in Washington presents many difficulties; therefore a description of the methods employed at some of the mines may be useful in planning operations in other regions, and is presented in this bulletin. The coals of Washington differ in quality, ranging from true lignites in Cowlitz County in the southern part of the State to anthracites in the Mount Baker district of Whatcom County, in the north~ rn part. Most of the output consists of subbituminous and bituminous coals, the latter including both coking and noncoking varieties. Analyses of the coals of the State and descriptions of the beds from which the samples were taken have been printed in publications of the United States Bureau of Mines.2 Details of coal beds and analyses of the coals of King, Kittitas, and Pierce Counties have also been published by the Washington Geological Survey; 3 and most of the coal beds of the State are described in some detail in a bulletin of the United States Geological Survey.4 In 1918 mining was in progress at 72 mines in the State 4a; 46 of these mines each employed more than 10 men underground. These mines were distributed as follows: Thurston County, 1; Lewis County, 7; Kittitas County, 14; King County, 16; Pierce County, 6; Skagit County, 1; and Whatcom County, 1. During that year a total of 5,847 men were employed, 4,172 underground and 1,675 on the surface. The average number of days worked in the State was 275, and the average yearly output per man was 706 tons. Coke is made only in Pierce County by four companies, which have a total of 341 beehive ovens. In 1918 they produced 93,699 tons of coke. Up to 1919 mining machines were little used in the State. In 1917 only 6.61 per cent of the coal :produced was undercut by machines. In that year 58.95 per cent of the coal was mined by hand, and 34.44 per cent was shot off the solid. The explosives used were as follows: Black powder, 36.6 per cent; dynamite, 38.l per cent; and permissible, 25.3 per cent. The State of Washington is divided naturally into two parts by the Cascade Mountains which extend north and south somewhat west of the middle of the State. The coal areas east of the range will hereafter be referred to as eastern Washington-though nearly all of it is west of the middle of the State-and that on the west side as western Washington. The geographical distribution of the coal fields is shown in Plate I. Exploration of the State has not been exhaustive enough to preclude the possibility of discovering, besides the foregoing, other districts that contain deposits of coal in commercial quantities.

Jan 1, 1924

By Henry P. Wheeler

H ELIUM (chemical symbol: He) is a member of a family of normally gaseous elements, which, because of their zero valence and corresponding lack of chemical activity, are called the "noble" or "inert" gases. It is a monatomic element with an atomic number of 2, and it exists naturally in two stable isotopic forms-He3, with an atomic mass of 3.0170, and He4, with an atomic mass of 4.0039. With the exception of a trace (10-6 percent) of He3, all of the naturally occurring helium is He4. Two unstable isotopes-He5, with atomic mass 5.0137, and He6, with atomic mass 6.0208-are listed by various scientists, but the existence of He5 is questioned by some of them. He6 is radioactive, with a half-life of 0.8 second. Helium was discovered in 1868 in the gaseous atmosphere surrounding the sun. Although several scientists studied the solar chromosphere that year, it is generally agreed that J. Norman Lockyer of England should be credited with the discovery of helium, which he named, deriving the word from "helios," the Greek name for the sun. It was not found on earth until March 1895, when William Ramsay of London produced a small amount from a sample of cleveite, a uranium-bearing mineral. In 1905, H. P. Cady and D. F. McFarland of Kansas found helium in natural gas produced from a well near Dexter, Kans., and for the first time a large source of helium became available.

Jan 1, 1952

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

A mineral grain finder is described which is easily constructed to fit onto the stage of a standard reflected light ore microscope.The device is most useful in relocating particular grains or mineral associations on 30 mm diameter polished sections. The use of the grain finder in the teaching of ore microscopy is outlined.

Jan 1, 1988

By Marcel Labbé

La largeur de l?armature peut être modifiée selon les besoins du client entre 48 " et 64" de largeur totale, donc 2 sections de 24" à 32". Ceci permet à l?opérateur d?effectuer le démantèlement de l?équipement pour le déplacement dans les endroits restreints. Le déménagement d?un niveau à un sous-niveau devrait se faire dans un quart de travail de 8 heures. L?option de largeur permet au client de choisir un équipement adapté à son environnement de travail (1). La largeur de la table de forage peut être modifiée selon les besoins du client entre 48" et 96". Cette particularité permet une meilleure stabilité, et plus de précision dans le forage (2). Il y a 4 pattes hydrauliques à chaque coin pour la stabilisation lors de forage (3). La table de forage a 360° d?angle de forage sur 3 côtés du transporteur. La table peut sortir de chaque côté du transporteur de 40 ½" à partir du centre du transporteur pour faciliter la mise en place de la foreuse dans les endroits difficiles d?accès. La plage de forage est considérablement agrandie. Cette caractéristique qui fonctionne hydraulique, permet à l?opérateur de forer sans être obligé de changer la position du transporteur pour des changements de trous. Tous les types de foreuse peuvent être installés sur cette table de forage (4). Sa petite dimension lui permet d?accéder, par des monteries de 30" de diamètre, à des sites de travail de 2,5 mètres de hauteur et largeur. C?est un équipement adapté aux gisements filoniens. Ce genre de gisement est de moins en moins rentable pour les compagnies minières. La mécanisation des ces gisements va permettre de les rentabilisés en augmentant la productivité et la santé du travailleur, en réduisant la dilution (5). Les manettes de contrôle de la foreuse, les mouvements de la table de forage ainsi que le déplacement du transporteur ont été installés selon les recommandations d?un ergonome. Des recherches ont été effectuées par ce spécialiste sur les cas d?accident survenus avec l?utilisation de ce genre d?équipement. Il a déterminé les positions le plus confortable que l?opérateur doit prendre pour éviter les douleurs prolongées (6). Le système de roulement est composé de 4 roues pleines installées sur 4 planétaires de 9000 à 15000 livres de capacité munis chacun d?un moteur hydraulique. Des freins ont été installés sur les planétaires pour assurer la sécurité de l?opérateur et faciliter le positionnement du transporteur lors du forage. Des roues rétractables peuvent être installées pour faciliter l?accès sur rail (7). Ce transporteur peut être alimenté par une puissance électrique plutôt que par une puissance pneumatique. Cette puissance électrique est fournie par un Power Pack qui transforme l?énergie en puissance hydraulique. Ce type d?alimentation est employé lors du forage de développement, mais il peut aussi être utilisé pour le forage long trou. Cet avantage permet au client qui a un problème de pression d?air d?utiliser l?électricité. Par contre si vous utilisez l?électricité mais que dans un secteur isolé le gros courant électrique n?est pas accessible vous pouvez utiliser votre équipement en utilisant la puissance pneumatique. Le changement d?alimentation énergétique se fait facilement (8). Cet équipement est construit pour effectuer 4 types d?activités : forage de développement de niveau et sousniveau avec l?installation d?un bras porteur, forage et pose de câbles d?encrage pour soutènement de terrain, forage de production long trou et forage de monterie ascendante et descendante. L?avantage est que vous investissez dans un seul équipement au lieu de 2 ou 3. Cet avantage vous fait économiser dans votre budget d?équipement. En plus cet équipement est construit pour de dure travaux et ne contient aucun système électronique (9).

May 1, 2001

During the last 20 years, more than 80 km (50 miles) of tunnels have been constructed in the Los Angeles, CA area. Recent projects include The East Central Interceptor Sewer (ECIS), completed in 2004. It spans more than 18 km (11 miles). The Northeast Interceptor Sewer (NEIS), completed in 2005, spans 11 km (7 miles). And the 2-km (1.3-mile) Metropolitan Transportation Authority?s Gold Line Eastside Extension (MCGLEE) was completed in 2006. All of the tunnel routes lay beneath heavily populated urban environments so minimizing ground surface settlement was critical to the success of the projects. Previous tunneling efforts in the Los Angeles area using open shield methods resulted in significant settlement that damaged roads, utilities, buildings and other structures. Earth pressure balance (EPB), or slurry machines, were specified for these projects to reduce subsidence risk. The contractors chose EPB tunnel boring machines (TBM) for the work. The closed and pressured face of the EPB TBM reduces loss of ground at the tunnel face and, when the machines are used in combination with gasketed pre-cast tunnel liners and backfill grout behind the installed segments, losses from over-cut of the excavated surface are also reduced.

Jan 1, 2008

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995