Search Documents

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By Sutham Niyomwas

Keywords: Al2O3-SiCW, Ceramic Matrix Composite, Carbothermal Reduction, Kaolin The formations of Al2O3-SiCw composite have been obtained in situ by carbothermal reduction of a mixture of kaolin and activated carbon. The reaction temperature was controlled at between 1400°C to 1600°C. The synthesized products were mixtures of alumina and silicon carbide in the form of whiskers. The effects of milling time of precursors and reaction temperature are presented. XRD and SEM analyses indicate complete reaction of precursors to yield Al2O3-SiC as product powders, with the SiC having porous and whisker morphology.

Jan 1, 2005

By R. Fragoudakis

AISI 4130 steel is a medium carbon Cr-Mo steel used in automotive, aeronautic and other general-purpose industries. In this study, 4130 steel fatigue specimens were carburized at 927oC to enhance the carbon content in the steel, raising it from approximately 0.30% (non-carburized) to 0.90% (carburized, oil quenched and tempered). Rotating bending fatigue tests were performed on the R. R. Moore Rotating Beam Fatigue Testing System, in order to determine the high cycle fatigue (HCF) life of 4130 steel and plot the corresponding S-N diagrams. A comparison of the results of carburized and non-carburized specimens shows that carburizing of steel: a) increases the surface hardness and b) improves the fatigue strength of the steel by at least two orders of magnitude.

Jan 1, 2010

By Yoshio Nakano

Keywords: Tannin gel, Palladium, Separation, Redox We have developed the novel recovery system of palladium from wastes, which is simple and generates little secondary waste in comparison with the conventional recovery processes, using tannin gel particles synthesized from condensed-tannin molecules. Pd is adsorbed onto the tannin gel particles through inner-sphere redox reaction mechanism: two-electron transfer from tannin gel to Pd(II) species, accompanied by ligand exchange between chloropalladium(II) complexes and tannin molecules. In addition, we propose the separation system of Pd and Au from Pd-Au mixture, which is feasible due to the difference in oxidization and reduction potential between Pd and Au species: PdCl3(H2O)? and PdCl42? are less adsorbable than Pd species containing fewer Cl, such as PdCl2(H2O)2 and PdCl (H2O)3+, while such a distinct difference between Au species is not observed.

Jan 1, 2005

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

By Zengjie Wang

Kinetic study of hydrochloric acid leaching of Panzhihua ilmenite from China is presented. Both temperature and concentration of hydrochloric acid have significant effects on the rate process of Fe dissolution from ilmenite ore, while the ratio of liquid to solid has little effect on the Fe dissolution. The Fe dissolution is found to follow the spherical model f (??) =1-(1- ??)1/3 and the apparent activation energy is calculated as 47.21 KJ/mol, suggesting a chemical reaction controlled mechanism. The dissolving behaviors vary at different kinetic stages. At the beginning the amount of the dissolved Fe and Ti increased monotonically with leaching time, while about 15 minutes later the dissolved Ti in the form of TiOCl2 began hydrolyzed into TiO2 fines reunited on the ilmenite ore surface, as observed by SEM and EDS technique. For the unreacted ilmenite particles covered by a layer of hydrolyzed TiO2, the leaching seemed to be as a selective leaching of iron and because Ti dissolved from and hydrolyzed rapidly again into the unreacted ilmenite particles. The leaching process can be ended 4 hour later when almost of Fe has dissolved into the solution and TiO2 remains as solid residues. The effects of acid concentration and leaching temperature were also investigated.

Jan 1, 2009

By Theo Lehner

"The Boliden Rönnskär Smelter operates in the European Context of tight EH&S limits, with ever increasing regulations and tribulations. The near future promises to bring new burdens in the form of C02 trading, miners and pre-treaters increased appetite for a larger share of contained values, and changing compositions and competition in raw materials. On the other hand, European Smelters such as Rönnskär, Harjavalta have demonstrated an astonishing power of survival. This presentation lists and comments on current challenges but opportunities for increased survival power are also presented. One example of the latter is the ongoing investment into increased treatment capacity for e-scrap.UPDATE ON RÖNNSKÄR OPERATIONSThe Rönnskär Smelter has achieved 80 years of age with no signs of retirement. The smelter is most active in spite of its age! And it has undergone some face lift operations to maintain its attractiveness.Raw material, processing facilities and a market for the products are some essential prerequisites for a viable operation. To justify long term survival, economic terms such as return on investments and positive cash flow need to be considered. Below, we illustrate how the Rönnskär Smelter complies with these terms. To update the reader on current operations, our current flow sheet is depicted in Figure 1. The figure summarizes our current input and output."

Jan 1, 2012

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By Dirk van Zyl

As part of the North American regional activities during the Mining, Minerals and Sustainable Development Project (MMSD) one project focused on the development of sustainability evaluations at the operations level. Engagement was identified as one of the seven important questions to be addressed. Engineers and scientists employed in the mining, minerals and materials production arenas must understand the importance of stakeholder engagement, both within and outside the operations as it is essential in the ongoing activities required to contribute to sustainable development. After developing the awareness that a social license can only be contemplated if engagement is in place, they also have to develop skills in engagement processes. This presentation will present the business case for engagement as well as an approach to motivate undergraduate mining engineers to embrace it. The presentation will also review some recent and ongoing research to improve the engagement process.

Jan 1, 2010

By R. Altman

A Brookfield viscometer fitted with a stainless steel bob was used to measure the viscosity of industrial lead blast furnace slags between 1126 and 1298°c. Slag oxidation state was characterized by first annealing the? slag samples at 750°c in sealed copper tubes in order to precipitate magnetite crystals. The magnetite concentration was then measured on an Outokumpu Saturated Magnetic Analyzer. Using an Arrhenius-type equation, a viscosity model was developed by regression. The equation below accounted for 75% of the variability in the data used to generate the regression coefficients and, on average, could predict viscosity within ± 12% of the measured value. The greatest difficulty encountered in measuring viscosity was due to the occasional presence of solids in the slag which caused, at times, erroneously high viscosity measurements. Precautions to minimize this problem are outlined in the text.

Jan 1, 1985

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Gabrielle Gaustad

For aluminum, substitution of primary with secondary resources decreases energy consumption; this energy advantage creates a strong economic incentive to recycle. Several authors have raised concerns that the current sinks for secondary materials may soon be saturated, impeding subsequent expansion of recycling. This work combines dynamic material flow analysis with optimal batch planning models to quantify the significance and drivers of these pending limits under several scenarios, and thereby explore potential opportunities to increase recycling. An aluminum recycling system case was developed that includes containers and packaging, automotive, and construction products and scraps. The impacts on aggregate scrap utilization and materials cost are explored in the context of changing alloy demand and lifetime. Insights drawn from this specific case study could be applied to multi-stakeholder, systemic models.

Jan 1, 2010

By Lassi Klemettinen

For better understanding and maximal value utilization of the WEEE smelting process, the behavior and distribution of different trace elements must be known. In this study, the behavior of nickel as a trace element was studied in an equilibrium system with metallic copper—spinel saturated iron silicate slag (with 3 wt-% K2O)—iron aluminous spinel—gas. The experiments were conducted in alumina crucibles at 1300 °C, in oxygen pressure range of 10−10–10−5 atm. A time series of 15–60 min experiments was also conducted for investigating the formation rate of the primary spinel phase in the system. The results show that the distribution coefficient of nickel between metallic copper and liquid slag changes from approximately 70 to 0.4 along the increasing oxygen pressure range. In addition, a significant part of the nickel deports into the spinel phase. The spinel formation was investigated based on composition analysis results and visual observations from SEM-images.

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003