Search Documents

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By Essie Esterhuizen, John Ellenberger, Dennis Dolinar

"Underground stone mines in the United States use the room-and- pillar method of mining. The stability of the roof between pillars determines the mining dimensions and size of equipment that can be used. The findings of a survey of roof span stability issues and design practices are presented, and the observed factors contributing to roof instability are discussed. Identified stability issues are evaluated, such as maximum roof span, horizontal stress, and roof beam stability. The results of field observations, roof monitoring, and numerical analyses are used in the evaluation. The importance of the first roof beam thickness and its impact on roof stability and support requirements is presented. An evaluation of the current experience with stone mine roof spans relative to international experience is presented. A step-by-step design procedure is suggested which emphazises the need to collect adequate geotechnical data, understand the immediate roof stability, select a mining direction, and meet support requirements.INTRODUCTIONIn room-and-pillar mines, the roof between the pillars is required to remain stable during mining operations for haulage as well as access to the working areas. Roof and rib falls account for about 15% of all reportable injuries in underground stone mines (Mine Safety and Health Administration, 2009). Therefore, the stability of the roof is an important safety consideration. The size of the rooms in underground stone mines is largely dictated by the size of the mining equipment. Large mining equipment is used, requiring openings that are on average 13.5 m (44 ft) wide by approximately 7.5 m (25 ft) high to operate effectively (Esterhuizen et al., 2007). The dimensions of the roof spans are largely predetermined by the equipment requirements, and design is focused on optimizing stability under the prevailing rock conditions. If the rock mass conditions are such that the desired stable spans cannot be achieved cost effectively, it is unlikely that underground mining will proceed. In addition, large roof falls can extend across the full width of a room and may extend more than 5 m (16 ft) above the roof line. These large falls are a safety hazard and can have a significant impact on mine access and production. The National Institute for Occupational Safety and Health (NIOSH) research into stone mine roof stability has focused on identifying both the causes of roof instability and techniques to optimize stability through design."

Jan 1, 2010

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By Pinnaduwa H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior of the rockmass surrounding the underground mine excavation. The aim of this study was to investigate, at the threedimensional level, the geotechnical behavior around a tunnel excavated in a metal mine in China. A three-dimensional numerical model was built by using the 3DEC software package to simulate a tunnel excavation under a high in situ stress condition and by relying on the information available on lithology, geological structures, in situ stress measurements, physical and mechanical properties of intact rock, discontinuities, and interfaces between different rocks. The authors also investigated the effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or equivalent continuum material and rock support system on the deformation, and stability around the tunnel. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses with appropriate geomechanical property values.

Jan 1, 2013

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By Selmar A. Oliveira

"Safe mine closure is an important step in the mining lifecycle. Plans for safe and efficient closure should begin at the inception of mining. Ideally, closure occurs when the reserve has been depleted. However, when the abandonment of a mine occurs prior to the depletion of the reserve, several problems arise which need to be treated. This situation occurred at Verdinho Mine, located in the state of Santa Catarina, southern Brazil. Verdinho Mine is a coal mine that operated for more than 40 years without had backfill technologies applied. Soon before the exhaustion of the reserves, it was abandoned by the owners without proper closure. As a result, the Federal Public Ministry filed a public civil action to promote proper closure. Several parties are currently involved, including the National Department of Mineral Production (DNPM), the mining regulator of the Brazilian Government. To meet the judicial determination, a cooperation agreement was initiated between DNPM and the Federal University of Rio Grande do Sul (UFRGS) to identify and to monitor parameters which could result hazard due flooding mine, to model the various conditions to minimize the impact of flooding caused by total abandonment. Many processes must be planned and planned early in mining operations, and these processes must be performed over the life of the mine. Financial resources must be guaranteed by a specific fund fueled by operating revenues. When these resources are not properly employed, costs and technical difficulties prevent proper closure progress. If the removal of subsoil equipment, treatment and control of groundwater, regeneration of the surface, and closure of openings are not done correctly, there can be environmental, social, and stability impacts over time. To avoid this in the future, a detailed study is being performed at the Verdinho Underground Coal Mine on how to appropriately implement mine closure and monitoring procedures. This study is being conducted in response to a lawsuit filed by the Federal Public Prosecutor’s Office. INTRODUCTION The nature of the Mining Industry is such that all mining is a temporary activity, where the operational life of a mine is defined by the final project scope. The operating life of a mine lasts from a few years to several decades. Mine closures occur once the mineral resource at a working mine is exhausted, or operations are no longer profitable. Mine closure plans are required by most regulatory agencies worldwide, such as the Mineral Production National Department (DNPM) in Brazil."

Jan 1, 2017

By Michael Gauna, Christopher Mark

"Underground coal mining in the U.S. is conducted in numerous regions where previous workings exist above and/or below an actively mined seam. Miners know that overlying or underlying fully extracted coal areas, also known as gob regions, can result in abutment stresses that affect the active mining. If there was no full extraction, and the past mining consists entirely of intact pillars, the stresses on the active seam are usually minimal. However, experience has shown that in some situations there has been sufficient yielding in overlying or underlying pillar systems to cause stress transfer to the adjoining larger pillars or barriers, which in turn, transfer significant stresses onto the workings of the active seam. In other words, the overlying or underlying pillar system behaves as a ""pseudo gob."" The presence of a pseudo gob is often unexpected, and the consequences can be severe. This paper presents several case histories, summarized briefly below, that illustrate pseudo gob phenomenon:• Pillar rib degradation at a West Virginia mine at 1100-foot (335 m) depth that contributed to a rib roll fatality.• Pillar rib deterioration at a Western Kentucky mine at 570-foot (175 m) depth that required pillar size adjustment and installation of supplemental bolting.• Roof deterioration at an eastern Kentucky mine at 1300- foot ( 400 m) depth that stopped mine advance and required redirecting the section development.• Coal burst on development at an eastern Kentucky mine at 1700-foot (520 m) depth that had no nearby pillar recovery.• Coal burst on development at a West Virginia mine at the relatively shallow depth of 1100 feet (335 m) that also had no nearby pillar recovery.The paper provides guidance so that when an operation encounters a potential pseudo gob stress interaction the hazard can be mitigated based on an understanding of the mechanism encountered.INTRODUCTIONThe U.S. underground coal mining industry has conducted mining in multiple seam environments, where the active mining has underlying or overlying old workings at varying interburden distances, throughout its history. Often no serious consequences arise from the multiple seam mining. However, sometime mines have been confronted with hazards from underlying or overlying workings that include localized roof and rib failure, pillar system failures through propagating roof falls and floor heave, and also pillar bursts."

Jan 1, 2016

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By Lou Gaozhong, Guo Wenbing, Zhao Gaobo, Wang Shuren

"The height of a fractured zone due to high-intensity mining (HIM) plays a vital role in the safety analysis of coal mining under bodies of water. This paper described the characteristics of HIM. The processes of overburden failure transfer (OFT) are analyzed. The state of destruction transfers from a certain stratum to the upper stratum as face advance distance increases, and the processes of OFT are divided into two stages: transmission development stage and transmission termination stage. Through theoretical analysis, the limited suspension-distance and limited overhanging distance of each stratum are proposed to judge the damage of each layer. Based on this, the OFT criteria of fractured zone development are obtained. The mechanical model of strata suspended integrity and overhanging stability are established. Finally, a new method to predict the height of fractured zone due to HIM is put forward based on the processes of OFT, the limited suspension-distance, and the limited overhanging distance. Further, a HIM panel in the Datong coal mine is taken as an example. Theoretical methods are proposed, and engineering analogy is used to predict the height of the fractured zone, which is compared with in-situ measurements reported in the literature. The results show that the in-situ measurements for the height of the fractured zone are in close agreement with the theoretical calculation result. Therefore, the rationality and reliability of the theoretical method proposed to predict the height of fractured zone is verified.INTRODUCTIONThe height of the fractured zone (HFZ) due to the exploitation of coal is a key parameter for the safety analysis of coal mining under a body of water (Wenbing, Youfeng, and Hou, 2012). Accordingly, it is necessary to predict HFZ under the corresponding mining conditions before coal mining."

Jan 1, 2018

By Thierry Lavoie, Mark K. Larson

"Engineers at the National Institute for Occupational Safety and Health (NIOSH) and Itasca Consulting Group, Inc., conducted a study to determine the procedure for calibrating a caving model implemented in FLAC3D. The model is calibrated to measured surface subsidence. This sedimentary caving model was developed by Itasca for NIOSH for the purpose of more closely simulating mechanical processes during caving. When a model is considered calibrated to surface subsidence, the load between the extracted panel's roof and floor is a reasonable estimate of gob loading. Such information can also provide an estimate of the amount of overpanel weight that is transferred to the abutment. This load distribution is a parameter needed, for example, to estimate loading of pillars in longwall gate roads. For the current case, a calibrated model resulted in a calculated abutment angle of 30.6°considerably higher than the assumed value used in empirical methods, but reasonable considering the presence of massive stratigraphic members in the overburden. Because of additional information available after this study that the extracted seam height was actually greater in the first panel, a corrected range of abutment angle was estimated to be from 27.7° to 30.6°, still significantly higher than the empirical assumption. The expectation is that better estimates of abutment loading profiles will result in improved evaluations of mine layout design and, therefore, reduce the number of fatalities and injuries resulting from falls of ground.INTRODUCTIONThe safety of miners in underground coal mines depends on careful consideration of the mechanisms involved in failure and transfer of load. The successful design of pillars and panels in longwall and room-and-pillar coal mining requires thorough attention to any information and measurements available that help understand these mechanisms. Although empirical methods, such as Analysis of Pillar Stability (ALPS) Mark (1987); (Mark, 1992) or Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), can provide a sense of success or failure, complex geology and failure in the roof or floor material or complex material behavior of the coal can make evaluation by an appropriate numerical modeling tool necessary. The numerical tool must simulate important mechanisms and appropriate detail that underlie the mechanism. For example, Starfield and Cundall (1988) advised using ""the simplest model that will allow the important mechanisms to occur, and could serve as a laboratory for the experiments you have in mind."" To that end, data gathering about the geology, geometry, and material behavior is very valuable. Such data facilitate selection of an appropriate model and model inputs. Moreover, this data facilitate improved assessment of risk to miners and how to minimize that risk."

Jan 1, 2016

By Uwe Wyink, Guenther Thiele, Isabel Gollnick, Klaus Thyrock

"The application of a thin spray on liner was implemented in longwall T-junction sections in 2009 for the first time. The development of the material and the application is based on a technical cooperation between RAG Deutsche Steinkohle AG and BASF Corporation. The report gives an overview of the first trials. The underground test occurred in a seam with a height of 1.5 m (5 ft) in a depth of 1,100 m (3,609 ft). The roadway is dual-use entry and the roof strata is composed of shale and sandy clay. In some sections geological faults impact the surrounding strata. The poor conditions induce separating and loosening of roof rock. Several remedial actions have to be implemented for decreasing deformations at the face entrance.The application of thin spray on liner (TSL) provides simplification and cost reduction of supporting work at longwall T-junction. The installation of TSL to avoid roof and coal fall operations for lagging are omitted.INTRODUCTIONFor safe operation of face retreat in dual-use roadways, the processes of securing and stabilizing the face end area are very important in order to minimize deformation and stress. Avoiding roof and coal fall are the main concerns for safe operation. For that reason different methods of reinforcement are tested in underground operation. In this paper the application of TSL is presented.The specifications of TSL are described, followed by the case study results. The underground study is located in one mine of RAG Deutsche Steinkohle. The extraction of the hard coal in this mine is characterized by great depth and high stress. There are poor geological and geotechnical conditions. The roadway used for the underground application was headed with the support system combination type A, which will be described later in the paper. After the first face retreat, deformation of steel arch support and bagging destroyed the roadway, so for the second face retreat remedial actions had to be undertaken. For this a new system of reinforcement, simplifying the supporting work at the longwall T-junction was tested. The reinforcement consisted of different parts that are described in the following report. Furthermore two different versions were applied. One method is the operation with TSL and the other one is the use of concrete for sealing. Both methods are compared in the text."

Jan 1, 2010

By Michael Murphy

A multi-stage triaxial procedure has been developed for the enhanced servo controls and feedback systems at the National Institute for Occupational Safety and Health (NIOSH) rock mechanics laboratory. Due to the difficulty of preparing multiple rock specimens for single-stage triaxial tests at different confinements, multi-stage testing provides a huge advantage if only a few samples of coal measure rocks can be prepared from the drill core. A multi-stage test can provide mechanical properties, post-failure properties, and a complete failure envelope for a single specimen. For the multi-stage test procedure, a parameter used to define the slope of the stress-radial strain curve was developed and monitored in real time in order to successfully predict peak strengths at different confining stages. For this paper, multi-stage tests have been conducted on sandstones of varying strengths, including Berea sandstone which has well-documented properties, and fine-grained and coarse sandstone from a western US coal mine. For the tests conducted on the fine-grained sandstone, it was found that the ramp rate was an important factor in the success of obtaining peak strengths during the multi-stage tests. For each rock type, a table including Young?s modulus, Poisson?s ratio, unconfined compressive strength, friction angle, cohesion, residual friction angle, and residual cohesion are reported. The values from these tables have been used as input parameters for projects at NIOSH requiring numerical model input parameters.

Jan 1, 2014

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015