Search Documents

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By E. A. Adey, C. Baciu, P. Whitbread-Abrutat, M. Varul, T. Ejdemo, R. K. Shail, F. Wall

Responsible mining requires stakeholder engagement throughout all operational stages and after mine closure. By assessing the current and anticipated future socio-economic and environmental impacts, a company can maximise the positive impacts they can have on a community, whilst minimising any negative impacts. Despite the current emphasis on companies maintaining effective stakeholder relations to gain their ‘social license’ to operate, findings of the present study reveal a wide variation in community expectations, with different degrees of ‘acceptability’ evident across seven sites in Romania (Rosia Montana), Sweden (Kristineberg), the United Kingdom (Cornwall), Bosnia Herzegovina (Vihovici) and Russia (Karabash, Gay and Mednogorsk). These variations reflect the current status of mining within a community, as well as its socio-economic background and the nature of existing engagement with mining companies already operating in the region.

Jan 1, 2011

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

A large-diameter road tunnel will cross beneath the strait in Istanbul and expand the infrastructure bottleneck between Europe and Asia. The technical planning of the tunneling operations poses complex challenges. Therefore, the construction consortium ordered a specially adapted tunnel boring machine (TBM) from Herrenknecht. The 13.6-m (44.6-ft) machine, a Mixshield, was completed in early July 2013 in Schwanau, Germany. To get from the European to the Asian side of Istanbul, people and goods have to cross the Bosporus Straits. So far, two road bridges as well as ferries provide the only transport link between the two parts of the city and the two continents. The tense traffic situation for the nearly 14 million residents of the city and for international transit traffic should be improved considerably thanks to the construction of a new road tunnel under the Bosporus. ?The project is certainly one of the most challenging tunneling operations currently being addressed in the world,? said Herrenknecht project manager Georg Schleer. The route of the ?Istanbul Strait Road Tube Crossing Project? runs around 100 m (330 ft) below sea level at its deepest point. The interior diameter of the tunnel will be 12 m (40 ft) so that two lanes in each direction can be accommodated. They will extend one above the other on two levels. 3.34 km (2.1 miles) of the tunnel with a total length of 5.4 km (3.3 miles) are being created by a 13.6-m- (44.6-ft-) diameter Herrenknecht TBM that will begin its underground mission from a launch shaft on the Asian side.

Sep 1, 2013

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By Sohta Takatsu, Hachiroh Mizubata, Shigeki Kudoh, Kazuya Takekuni, Yoshinori Yamada

A special type of shotcrete is used to improve the performance of open-type TBM in difficult situations. The Hakamagoshi and Johana tunnels are expressway evacuation tunnels of 3.2 km and 5.1 km in length, respectively (total 9.1 km) that were excavated by one open-type TBM. The geological conditions at the sites were estimated to be good before excavation. However, 95% of the rock turned out to be two ranking orders worse than the estimated classes. Therefore, we used a special shotcrete for bad rock conditions, and succeeded in excavating the tunnel at an average rate of 270 m/month.

Jan 1, 2001

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.