Search Documents

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By Sushil Bhandari, Amit Bhandari

Blast optimization in open-pit operations is a task that often remains at a theoretical stage. Indeed, when it comes to operational blast design and onsite implementation, time restrictions and field conditions make it difficult to execute a planned pattern accurately and optimization according to local conditions is even more difficult. For example, adjusting a drill pattern to a complex face geometry is not something that can be easily undertaken on site. Blasters and engineers will do their best trying to distribute boreholes over the bench and even then, it can take them hours to achieve an acceptable layout. Similar situations occur with delay sequences, when trying to adjust them to address selectivity or vibration issues. For these reasons, operational blast design will often remain at a very basic level and the required adjustments are laid aside due to the difficulty of implementing them on site.

Jan 1, 2019

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018

By Randall M. Wheeler

The measurement and analysis of blast-induced ground vibrations are more complex than ever before. This is primarily due to the advancements made in microchip technology, mass storage utilities and the computer, which have allowed us to reduce and analyze data in a matter of moments instead of days. Terminologies such as Fourier transform, response spectra, cross-correlation, convolution, deconvolution and half-length frequency, etc. mean little to anyone except those who are experts in the field. A little understanding of the basic concepts behind vibration effects can help a beleaguered end-user feel more confident about what their measurements really mean.

Jan 1, 1992

By Jackson R. Pressley, Bruce Vandenberg

An explosive’s velocity of detonation, (VOD), can be used to indicate a number of important characteristics regarding the product’s performance, under specific field and test conditions.

Jan 1, 1997

By Catherine Aimone-Martin, Mary-Alena Martell

Whole-structure and mid-wall responses of 33 non-traditional structures to surface coal mine blasting were characterized. Eighty-nine blasts were conducted at 11 mine sites throughout the U.S. to measure blastgenerated dynamic response of structures typically found in the proximity of surface coal mining. Structures selected for this study include log-type, manufactured (single- and double-wide trailers), “mine camp”-type, adobe, and stone. Traditional acoustic microphones, t&axial (ground) and single component (structure) velocity transducers were used to record airblast, ground motions, and structures response time histories with a common time base. Wall crack displacement gages were used to record static and dynamic movement of existing drywall cracks. The relative responses of selected “atypical” structures to blast vibrations and nonblasting causes of structural stress, including natural forces, environmental effects, and human habitation, are compared. The purpose of this study is to document and compare vibration characteristics of structures that were not included in previous studies conducted by the U.S. Bureau of Mines and others in establishing the widely adopted safe level blast vibration criteria in the U.S. An important objective of this study is to outline an evaluation process including structure uniqueness relative to cracking susceptibility.

Jan 1, 2002

By Lawrence W. Gubbe

Air blast associated with detonation of explosives in mining, construction or military applications is often responsible for complaints by people who live or work in the vicinity of the activity. Most often, the complaints are based on the perception that vibration caused by the airblast damaged one or more residential buildings that may be located within several hundred feet or several miles from the blast site. The potential for airblast to cause damage is related to the amplitude and frequency of the airblast overpressure wave at the receptor. Amplitude and frequency of the overpressure wave are, in turn, dependent upon the type and amount of explosive detonated; the degree of confinement; the distance the wave travels; the topography between the blast site and the receptor; and, atmospheric conditions. It is well known that, as the result of atmospheric focusing, the amplitude of airblast overpressure that exists relatively far from the blast site may be substantially higher than the amplitude associated with the attenuated wave in an isotropic atmosphere. Two methods are available to predict baseline overpressures 1) the Sandia Laboratories, Atomic Energy Commission method as extended by the Naval Ordinance Laboratory (NOL method) and the Ballistic Research Laboratory method (BRL method). These methods are developed by different techniques, are based on different idealized atmospheres and predict widely different results. The amplification factor applied to account for the effect of focusing must be consistent with the method used to predict the baseline overpressure. Theoretically, the amplitude of the overpressure at distances several miles from the blast site could be more than 25 to 100 times the amplitude of the attenuated wave predicted by the BRL method. However, based on comparisons with measured overpressure data is probably less than approximately 3 times the amplitude of the attenuated wave as predicted by the NOL method. This paper is based on research conducted as part of investigations of airblast damage complaints associated with an accidental explosion near Eveleth, Minnesota and with the disposal of military explosives by detonation at the Sierra Army Depot near Herlong, California. The techniques available for estimating the airblast overpressure that might be generated at various distances from the blast site and criteria for evaluating the potential for damage are examined.

Jan 1, 2004

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By Joseph Daly

This is the detailed evaluation of the establishment and implementation of an ‘oil recycle plant’ located on site at Boggabri Mine NSW, (Australia); its production, its use and its value. Also discussed in detail is the quality of the raw material produced, and the process and initial application of this raw material generated as well as the analysis of such, as a component within bulk explosive as applied to the mining industry as compiled during analysis. Laboratory analysis prior to field testing is also discussed including independent external laboratory analysis as well as the environmental benefits and a business case for recycled oil in blasting. This paper includes technical details of the product including densities, velocity of detonation and other associated key performance indicators. The intention is to off-set the amount of Distillate (Diesel) utilised as a component of bulk explosives, with a raw recycled oil and thus reducing both the environmental carbon footprint as well as production costs with regard to introduced petrochemical production and utilisation; an oil that is an existing recourse of controlled waste not only difficult but expensive to otherwise dispose of, whilst keeping the entire process ‘on-site’. Though recycled oil in blasting is not an entirely original idea, the key feature of this paper is the ability to complete the entire process on-site.

Jan 1, 2014

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995