Search Documents

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By Gjergj Dodbiba, Toyohisa Fujita, Li Pang Wang, Masashi Yamane

"The platinum-group metals (PGMs), are currently receiving worldwide attention as they have major industrial uses. PGMs, i.e. ruthenium (Ru), rhodium (Rh), palladium (Pd), osmium (Os), iridium (Ir), and platinum (Pt), are widely used as catalysts in petroleum and chemical processes. In addition, they find wide applications in automotive exhaust-gas control converters and are of immense importance to the electronic industry. Broadly speaking, PGMs are extracted in minute quantities from a limited number of ores, found mainly in South Africa and Russia. As the PGMs are both costly and almost indestructible, they are usually recycled from various forms of scrap. In other words, the recycling of the PGMs is an essential factor in the overall management of the PGM economy. In addition, the ever-increasing user areas have created renewed interest in the search for new sources or deposits of PGM, which in turn requires an in-depth knowledge of its characteristics. In this work, the emphasis is placed on the need to analyze the composition and microstructure of blast-furnace slag for recovering PGM metals. In other words, chemical composition, surface analysis and microstructure analysis of the DC arc furnace slag have been carries out. The aim is to provide a detailed analysis of this material for anyone with an interest in gaining further knowledge of its specific content for recovering PGMs."

Jan 1, 2014

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By Derek Caizergues, Hurman Eric

Experiments have been conducted at around 1700°C to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

The multiphase reactive flow in process equipments, e.g., fluidized beds, involves complex coupling among flow, heat/mass transfer and reaction kinetics over scales ranging from molecules, sub-particle eddies up to equipments. Conventional two-fluid model (TFM) ignores the effects of meso-scale structures, and hence is not suitable for describing the intrinsically multi-scale heterogeneity within multiphase systems. To be consistent with the meso-scale structures, we proposed a structure-dependent multi-fluid model (SFM), and closed its drag force by invoking the stability condition defined in the energy-minimization multi-scale (EMMS) model. The SFM reduces to the conventional TFM if homogeneous distribution is assumed within each grid, and reverts to the original EMMS model if it is used to describe steady state, global behavior of a fluidized bed. The multi-scale computational fluid dynamics (CFD), which is characterized by coupling of TFM and EMMS drag coefficient, can then be viewed as a simplified solution of the SFM. We demonstrate that the SFM significantly improves the accuracy and at the same time enables higher efficiency by allowing for much coarser grid used than in TFM. Recent application of it in 3D, full-loop, transient simulation of industrial processes, e.g., fluid catalytic cracking, coal combustion, gasification, kaolinite clay calcinations, shows its advantages in helping design and troubleshoot multiphase process equipments. Keywords: meso-scale, SFM, multiscale, CFD, simulation, structure, EMMS, multiphase

Sep 1, 2012

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003