Search Documents

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Michael Lane

With the success of their existing casino operation on the Ohio River in Lawrenceburg, Indiana, the Indiana Gaming Co., LP planned a major expansion of the current facilities. This expansion includes a second 1400+/- car parking garage, a new surface parking lot, elevated walkways, and a new floating casino that will double their present square footage and consolidate all of the gaming activity to one floor. In March of 2006 Richard Goettle, Inc. was awarded the general contract to construct a 260? x 520? boat slip for the new Argosy VII floating casino. An Open Cell® bulkhead system was specified as the means for constructing the new slip. Our contract included the purchase and installation of 300,000 square feet of PS27.5 sheet pile, excavation of 230,000 cubic yards of soil, and a 3300 square foot Mechanically Stabilized Earth wall.

Jan 1, 2008

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016

By James A. Schneider

Selection of resistance factors within Load and Resistance Factor Design (LRFD) requires accurate assessment of uncertainty and bias in load and resistance. To date, many studies have focused predominantly on the assessment of uncertainty, while the potential for bias appears to be the dominant factor in design for consistent levels of reliability under a variety of situations. Bias comes from factors which have been ignored in design method development but significantly influence resistance when extrapolating from conditions typical of databases to those at a given site. Uncertainty and bias can be quantified as the coefficient of variation and mean (or median) of a data set, respectively, for statistical assessment of load and resistance factors. This paper first presents an overview of statistical assessment of resistance factors, and then discusses factors that influence uncertainty and bias when extrapolating to situations outside of conventional databases of driven pile axial capacity.

Jan 1, 2009

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Rick Deschamps

The Block 76 project includes the demolition and redevelopment of an entire city block for mixed use retail, office and residential properties directly adjacent to Historic Temple Square in Salt Lake City, Utah. Excavation was carried out 65 ft below street grade and by as much as 50 ft directly below adjacent buildings supported by shallow foundations. Movements of the earth retention system and adjacent buildings were monitored in real time using automated equipment which complemented traditional geotechnical instrumentation. In the areas immediately adjacent to the existing buildings 9 stories or greater, anchored diaphragm walls were employed. Areas of the site not supported by diaphragm walls employed a soil nail wall system. Jet grouting was used for water cutoff in lieu of dewatering along the north and east sides of project. In total, the earth retention scope included 45,000 sq. ft of diaphragm wall, 104,000 sq. ft of soil nail wall, and micropile underpinning of 3 buildings. This paper provides an overall description of the Block 76 project. A detailed account is provided of the technical and commercial lessons learned. The project provided a unique example of how an owner can receive best overall value by acceptance of some technical risk up front. Benefit was gained by allowing the contractor to reduce contingencies within the bid from unknowns on a fast-track project.

Jan 1, 2009

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000