Search Documents

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By L. J. Heaslip, J. M. Toguri, T. R. Meadowcroft, R. L. Addinall

"""Pilot Plant Operations"" is a final-year core course given to the Metallurgy and Materials Science students at the University of Toronto. This course involves a laboratory study of an industrial project at an industrial site. Details of this program are discussed and reviewed after eight years of experience. IntroductionEducators in the field of Metallurgy and Materials Science have long agreed that ""hands-on"" experience is an important component in the education of metallurgical engineers. This philosophy is reflected in the undergraduate curricula of most metallurgical schools. The major problems encountered with laboratory-associated courses are the requirements for equipment, space and funds for both purchase and maintenance of equipment. For example, consider an exercise in crushing and grinding treatment in a mineral processing laboratory. Such operations require the handling of tons of material and often equipment of large size. The problems of storage of ore, methods of handling and maintenance of equipment are a few of the concerns facing the department. Considering that metallurgical departments at universities are, in general, relatively small, the support to purchase and maintain largescale equipment becomes an annual budgetary concern. In reality, universities today are not geared to operate mini-pilot plant equipment, either in terms of space or personnel.For the above reasons, in 1972an undergraduate core course called ""Pilot Plant Operations"" was introduced to the fourth year curriculum in Metallurgy and Materials Science at the University of Toronto. This course consists of I to 2 full weeks (8 hrs per day) of pilot plant laboratory study at an industrial site on a project of mutual interest with the industrial organization whose facility is being used. The first 5 years of the program were carried out at the pilot plant facility at the Ontario Research Foundation; Stelco's Research Centre in Burlington, Ontario, was used for the last 3 years. The nature of the projects undertaken during the 8-year period is shown in Table 1."

Jan 1, 1980

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"Aggregation, i.e., the tendency of particles to cluster, can be expected to influence flotation selectivity. In this paper, a method of measuring aggregation is introduced and used to conduct plant surveys.Aggregation is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to most dispersed and 1 to most aggregated over the range of conditions tested, normally pH. Surveys of Cu and Zn flotation stages at four concentrators showed the AI increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important. In doping tests, Mg was shown to cause significant variation in AI over the pH range of 9 to 12.The impact of Mg was restricted to pH > 9. Over this pH range, Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. An aggregation mechanism associated with these precipitates, electrostatic bridging, is suggested. Possible problems and opportunities in flotation practice arising from the findings are discussed."

Jan 1, 2002

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By R. Clarkson

"The Yukon's numerous (185) placer gold mines are still a major social and economic force in this developing economy. Gold recovery at each of the various sluiceboxes is not optimized due to extremely difficult sampling logistics and a shortage of technical expertise and industrial research.At each of six operating placer mines, numerous sluicebox tailings samples were collected with hand held sample cutters and combined into large (2-7 cubic yards) duplicate samples. The entire sample volumes were screened and processed on a shaking table to determine gold losses. The existing and potential gold recoveries and recommended sluicebox design and operating parameters are presented.2 ACKNOWLEDGMENTSThe Project Manager gratefully acknowledges the following support for this placer research program:The funding received from the National Research Council's Industrial Research Program, the Canada/Yukon Economic Development Agreement and the Canada Center for Minerals and Energy Technology (CANMET): andThe technical advice provided by Tad Cienski (CANMET), Ron Johnson (KPMA), George Poling (University of B.C.) and Dan Walsh (University of Alaska).3 OBJECTIVESThe objectives of the Gold Recovery Project are to: evaluate gold losses with statistically based sampling programs; determine how to improve gold recovery; assist miners with the recommended technology and make this information available to the entire placer industry."

Jan 1, 1990

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By J. C. Kingston

Introduction The sliding-form method of erecting concrete structures was first devised and used in the early part of this century by the Sante Fe Railroad Company for the erection of a grain elevator at Santa Fe, New Mexico. A somewhat related principle has been employed for a number of years in shaft lining work and, to our knowledge, was perfected in Butte, Montana, but until the building of the concrete headframe at the Jeffrey mine of the Canadian Johns-Manville Company, Ltd., at Asbestos, Que., the method, as applied to surface structures, was quite foreign to the mining industry in Canada. The current shortage and cost of structural steel shapes has no doubt contributed more than any other single factor to the investigations that have led to the use of reinforced concrete as a headframe building material. Mining men in western Quebec and northern Ontario have shown a great deal of interest in the design and construction of the headframe at the East Sullivan mine in Bourlamaque township, Que., and we have had many queries regarding the methods used and, in particular, for an explanation of the sliding-form principle. This article is written in an attempt to set forth the conditions which were to be met; to explain the construction methods used, and to discuss the economy of concrete headframes as compared with the conventional steel structures with which the mining fraternity is familiar.

Jan 1, 1949

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005