Search Documents

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

In late 1989, first-pass reconnaissance exploration delineated a 4km x 6km geochem- ically anomalous area centred 10km WNW of Kainantu in the Eastern Highlands Province at 6¦13'S and 145047'E. The area, named the Basangka prospect, lies between 2 200 and 2 400m asl. Interest in the area was prompted by a 14ppm Au assay of a silica-pyrite breccia float sample taken near Henkai village. The prospect was defined after several acid-leached silica- pyrite breccia and comb textured quartz float samples returned assays above lppm Au and relatively high Ag. Very encouraging and anomalous Au values were obtained from panned concentrates, despite the absence of visible Au colours. Several pan concentrates returned greater than 1mg Au and it is believed that the Au occurs as inclusions within iron oxides which were originally pyrite. In this early stage of prospect exploration, any Au value above 0.lppm in- 150# fraction stream sediments is treated as anomalous. Rock chips, panned concentrates and -150# fraction geochemistry all vividly define the areas of interest at Basangka.

Jan 1, 1991

Variations in delay timing can have a marked influence on blasting effectiveness and, hence, on total production costs. In single-row bench blasts, delay firing is invariably more effective than simultaneous initiation. In single-row delayed blasts, there is an optimum inter-hole delay above and below which inferior blasting results are obtained. This optimum delay is equal to the time required for each charge to just effectively detach its quota of the burden. The inter-hole delay should seldom be less than 4 ms.m-l of burden.In multi-row blasts in which holes in a given effective row are fired on the same delay, the entire burden on any effective row should be detached from the rock mass just before charges in the next effeotive row detonate. Delays shorter than this give inferior blasting results and an increased likelihood of environmental and slope stability problems. If the inter-row delay is too long, cut-offs can occur, especially where the delay unit is located outside the blasthole. For a surface delay system, the optimum inter-row delay usually varies between 4 ms.m-l and 8 ms.m-l of effective burden. The number of rows that can be fired effectively with surface delay systems (in a single blast) is limited by the threat of cut-offs. Greater interrow delays and a larger number of rows per blast can be fired to advantage with down-the-hole delay systems.There are practical limits to the timing accuracy of all available delay systems. The existence of delay time variability should be recognized and duly considered in the design of blasts.The relationship between delay timing and blasting vibrations is not discussed.

Jan 1, 1977

By Dunlop GA

Pilot Plant confirmatory testing of the treatment route developed in the Metallurgical Laboratory is an essential factor in the development of complex ore bodies. Objectives should be well defined to permit the efficient planning and cost effective operation of the pilot plant project. The primary objective for the pilot plant should be to confirm the viability of the developed flowsheet on a continuous basis, examining only major variables such as ore types, quantum changes in grind, comparison between bulk and sequential flotation circuits, use of flotation columns, evaluation of autogenous grinding and production of samples of concentrates for market evaluation. Secondary objectives may include the collection of engineering design data and the production of a comprehensive report to Bankable Document standards to provide technical support for capital financing. The complexity of the ore body and the scale of the final operating project together with the pilot plant objectives will determine the extent of the pilot plant operations. The level of expenditure associated with a pilot plant can vary, in total cost and as a percentage of the total development capital investment required to take the prospect from exploration to a producing mine. Factors contributing to expenditure are discussed. Associated with cost considerations is the level of confidence mining company investors can have that their capital investment will return dividends.

Jan 1, 1990

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

In the Bendigo district, with its large number of comparitively small leases worked by separate companies, we might naturally expect to find many different arrangements of winding machinery and, as a matter of fact, there are steam winches, old portable engines, single and duplex geared engines, twin engines on the first motion, and in one instance a single engine on the first motion, all employed for hauling purposes from depths of 1000 feet and over.It would be impossible in the compass of this paper to discuss at all fully the various arrangements of winding gear employed on the field the writer can simply refer to some of the more prominent features, in the hope that the information may prove of interest and benefit to the mining community. In criticising our machinery it must be remembered that when many of the plants in use at the present time were erected, they were not intended to wind from more than one third of the depths now common on the field; but so long as the machine could be made to haul a tank of water from the bottom of the shaft it has remained, the greater power required being obtained by increasing the piston speed and altering the gear wheels to suit. The consequence is, of course, that in some of our mines the speed of winding is painfully slow this feature, however, though certainly not consistent with modern ideas of economical mining, does not so seriously affect Bendigo as it would other fields, for the comparatively small quantity of stone to be raised from a given reef by some...

Jan 1, 1902

The centrifugal elevator invented and patented by the writer is designed for the purpose of conveying the tailings of a gold dredge to such a distance that it shall not impede the dredging opperations. Formerly this was usually accomplished by means of a belt of buckets travelling round a ladder set at an angle of about 30 degrees to the horizontal, but this meant heavy wear and tear on the travelling buckets and the tumblers actuating them. The centrifugal elevator throws the tailings through the air to the required height and distance and it is manifest that during their flight from the elevator to the heap there is absolutely no wear and tear, only the attraction of gravity and the resistance of the air has to be overcome. All then there is left to he considered is how to throw the stuff with the minimun of prower and wear on the elevator.The elevator consists of a cam-shaped steel casting with a disc of mild steel plate on either side: These side plates project a few inches beyond the tips of the beaters, in order to prevent odd stones from straying in an undesired direction; they serve also to prevent extra large stones from reaching the beaters, for they slide off the rims into the water.

Jan 1, 1904

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

When asked to lecture at Bendigo on the geological factors that determine the depths of ore deposits, I hesitated for a little before agreeing to lecture on the theory of deep ores in the city world famous as the pioneer of deep gold mining. If there be one place, wherein the conditions of deep-seated ore deposits should be sufficiently well understood, it is the city where the 180 mine made its bold plunge to previously neglected depths; and where the record of that famous mine has been broken by the skill of the managers, and the pluck of the proprietors, of the New Chum Railway and Lazarus mines.In the face of such practical triumphs, theoretical discussion may seem a waste of time, especially since it is often dedared that the existence of such deep-seated ores was denied by geological theory. This assertion is, however, startling since the oldest and best supported geoiogical theory of ore deposits, has taught for more than a century tliat ores must descend far below the regions of practical mining. This charge against Victorian geologists is generally based on opinions attributed to the late Sir Fredrick McCoy. It has been repeatedly affirmed that he declared that gold cannot occur pelow a depth of 300 feet. But so far I have not been able to discover that McCoy ever made any such assertion or ever held such a view.

Jan 1, 1902

By Wylie A. W, Mathew PJ

Bulk density and grade were determined on a variety of ore samples from the Mount Tom Price iron ore mine and the interrelationship between these properties and porosity deduced.Variable porosity is responsible for the wide scatter of data points and low accuracy of prediction in the grade of a single sample from grade/bulk density relationships.However, with a sufficient number of such data points, as from a nuclear geophysical borehole logging operation, the mean ore grade in an exploration-type drill hole (~63 per cent Fe) could be determined by regressionanal~sis with 95 per cent confidence intervals of approximately ± 1 per cent Fe. From the same logging operation, utilizing core data for calibration of the probe, the -mean fractional porosity for the drill hole (0·19 ± 0·016 at 95 per cent confidence interval) was deduced. This is less accurate than the corresponding result obtained on core material in the laboratory (0·20 ± 0·005).The range of porosity was from 0·08 for dense, high grade sectIOns of the ore, to 0·28 for friable ore of high grade or goethitic ore of lower grade. Shale band porosity ranged from 0·15 to anomalously high values of 0·48 believed to be caused by leaching of iron minerals from the shale. Porosity values for the iron ore component of the deposit are comparable to those found for the Cockatoo Island (W.A.) mine, and for sections of the Krivoy Rog (Ukraine) iron ore deposit of the Soviet Union.

Jan 1, 1978

WITH the exception of the deposits of the Milburn Cement Co near Dunedin, Wilson's Portland Cement Co., on the Mahurangi River (a short distance north of Auckland), and those of the New Zealand Portland Cement Co., at Limestone Island, the cement. Tesources of New Zealand remain practically undeveloped. The Milburn Company utilizes a mixture of limestone and mud for the manufacture of cement, while Wilson's and the New Zealand Portland Cement companies both have the advantage of a natural cement stock which requires but small additions of highgrade limestone to give the mixture required. The plant and deposits of the New Zealand Portland Cement Co are located in Whangarei Harbour, some six miles from thetownship of Whangarei. The works and dwelling-houses are situated on Limestone Island, which, with an area of 92 acres, and rising to a height of 212 ft., supplies the bulk of the raw material required. In addition to the island, the company possesses a high-grade limestone area of, roughly, four acres, situated on the mainland, 11 miles to the south. A better location for a cement works could not well have been chosen. On the east side of the island there is a deep channel, which never shows less than 18 ft. of water alongside the company's...

Jan 1, 1912

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

The first mention of gold in Western Australia was in 1848 when some specimens of copper ore, which are believed to have come from the Murchison district, were sent to Adelaide for assay. Gold was present in these specimens, but no particular interest seemed to be attached to this fact as the search at that time was mainly concentrated on base metals and coal. Interest appeared to be shown in gold in 1852 when several parties moved out eastwards from York looking for goldbearing country. Though these parties inmany cases were very near to what is now known as the Yilgarn Goldfield, nothing was found.The next record of gold was reported in some specimens which were brought in from Cardup, some 25 miles from Fremantle. Though this area was investigated, it would appear that all the gold had been contained in the specimens and nothing further was found, though the report had been the cause of a small rush of people interested in gold.From time to time specimens had been brought in by various people from the district east of Northam, and in 1861 a reward emanating from private sources was offered for the finding of gold within a radius of 150 miles from Perth. The Government at this stage took an interest in exploration for gold and in the same year supplemented this privately offered reward on a £ for £ basis. The Government also, about this time, commissioned a practical miner, with prospecting experience in the Eastern States, to examine the country between Albany and Northam with a view to the possible existence of goldbearing veins in that area. His report, however, was entirely unfavourable and nothing further was done. In 1873 a quartz lode was discovered near Albany arid a company was formed to work...

Jan 1, 1956

The Physiographical Features of the Region The Middleback; Range proper, from the Iron Duke in the south to the Iron Prince in the north, extends in a meridional direction for 21 miles, but may well be taken to embrace also the Iron Knob and Iron Monarch prominences so that the total length of the Range is 37 miles.Although no great altitudes are reached, the slopes of the high country are steep and the Range stands out prominently above the peneplaned surface of upper Eyre Peninsula. The Range is built up of sub-parallel ridges at some places, and its continuity is interrupted by transverse breaks or gaps resulting from normal stream erosion and corrosion during earlier periods when precipitation was heavier and streams were more active. Traces of high-level gravels remain on the flanks of Kimba Gap. A former mature stream on the western side of the Range has had its lower reaches blocked by sand and the old stream channel has been converted into an eiongated basin of internal drainage. The sand dunes in this area appear to be practically stationary at present, being fixed by mallee vegetation. Their trend is west-northwest.The relief of the Range is regarded as having been determined primarily by meridional strike faulting and selective silification of some of the beds. Dip faulting on the Iron Duchess leases has produced subsidiary features only.The Rocks of the Region: In order that some of the points made in the discussion of the genesis of the ore bodies may be appreciated it is necessary to consider the stratigraphical succession and the igneous types represented. This classification may be...

Jan 1, 1949

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. The main problem with these models is the inability to solve real size mining problems. We present a mixed integer linear programming formulation for the open pit long-term production scheduling problem. To reduce the number of binary integer variables in the formulation, we aggregate blocks into larger units referred to as mining-cuts. We present a semi-supervised clustering algorithm which aggregates smaller blocks based on rock types and grade ranges into mining-cuts without introducing an error in the grade estimated values. The cluster-based aggregation algorithm is fully integrated into an MILP mine production scheduling prototype software. We have implemented, verified, and validated our models. The efficiency of the new platform is evaluated through iron ore mine case study.

Dec 6, 2010

By Crook KAW

New sedimentological and biostratigraphic data indicate that the Leron Formation in the Markham Suture Zone, Papua New Guinea (PNG) represented Pleist- ocene alluvial fan-delta deposition in shallow marine to lacustrine environments. The distribution of sedimentary regimes in the Leron Formation indicates that during collision zone evolution, various tectono-sedimentary regimes do not always track the movement of the triple-junction systematically as idealized by Crook's (1989a) model. The migration of various tectono-sedimentary regimes are also controlled and influenced by the effects of second-order geometric features of the convergent margins. Leron Formation in the Markham Valley represents late to post-collisional marine to fluvial molasse. Foraminifera indicate that the collision and concomitant suturing of the Markham valley occurred after 1.32Ma.

Jan 1, 1991