Search Documents

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

By Sherwin F. Kelly

PLAIN mining engineers usually avoid any gathering of geo¬physicists because of the incomprehensibility of their discussion to the uninitiated. This being so, gradients, gravity and gammas will be deferred to the end of this review, the first part of which will be devoted to what has been done in applying geophysics to the solution of real field problems. From the West, J. J. Jakosky reports that International Geophysics has had its activities fairly well 'divided between mining (both placer and lode), oil structural work, and clans-site and reservoir investigations. In oil exploration, electrical methods are used for depths down to 2500 ft., beyond which they utilize seismic methods. They find in their placer work that the many 'magnetic anomalies encountered in the bedrock of the Southwest render the electrical techniques more satisfactory, and with them they are obtaining thickness and tonnage of gravels, depth to and contour of the underlying bedrock as well as important structural features therein, and water-table elevations.

Jan 1, 1934

By H. W. Straley

Some ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbeet.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information On' (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college "algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1946

By H. W. III Straley

SOME ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbert.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information on: (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1941

By H. W. Straley

Some ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbeet.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information On' (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college "algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1946

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine's considerable pyrrhotite production. The success of this project is of great importance to Japan's economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

ALABAMA. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Belle Ellen.-Hutcheson, W. C. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co Dobbs, G. G., Box 97. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., 1. & R. R. Co. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Brown-Marx Bldg. Coxe, E. H. Tenn. C., I. & R. R. Co. Crawford, C. G., Tenn. C., I. & R. R. Co. Crockard, F. H., Brown-Marx Bldg. Ellis, E. E.,1515 Brown-Marx Bldg. Fairbairn C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Geismer, H. S., Keiser-Geismer Engrg. Co.

Jan 1, 1917

By J. N. Roberts, K. V. Gow

In a recent review of the field of plastic deforrnation of metal single crystals, Maddin and chenl indicated the need for systematic investigations of the crystallography of the slip process with special attention to: a) The effect of the orientation of a crystal on the appearance of slip lines, b) The effect of high temperatures on the slip systems of aluminum, c) The effect of strain rate on the crystallography of slip. The present paper deals with the effect of temperature and strain rate on the mechanism of deformation of aluminum single crystals similarly oriented for single and duplex slip. The work of several investigators has shown that in aluminum at high temperatures other slip systems in addition to the predicted {I l l) <101> may operate. The most generally reported additional systems

Jan 1, 1959

Alfred E. Hunt, Pittsburgh, Pa. (communication to the Secretary): Mr. Blue&apos;s statement (page 576) that, " owing to the presence of iron and other impurities, makers of aluminum. assert that native corundum is unsuited for the production of that metal," is somewhat incorrect, at least so far as it may refer to any objection made by the officials of the Pittsburgh Reduction Co. to the Canadian corundums. We recognize corundum as among the richest and purest of the ores of aluminum, and the material furnished from Canada would offer for us the advantage of a supply near to our works for the manufacture of aluminum at Niagara Falls. The real difficulty which we find in the use of corundum for this manufacture is the cost of the raw material as compared with that of native bauxites. In this item we include not only, the price of the corundum as it has been offered to us, but also the expense of grinding it to an impalpable powder, which must be done before it can be used directly in the manufacture of aluminum, and the cost of preliminary chemical treatment for purification—which latter operation, however, is also required for bauxite. I agree with Mr. Blue that the introduction of new and irnproved processes has greatly reduced, during the past ten years, the cost of manufacturing aluminum; but I am inclined to believe that any further improvements, facilitating the use of corundum for this purpose, would apply, in equal or greater degree, to the common clays (silicates of aluminum) which exist in all parts of the world, are more easily mined and handled, and are likely to be always cheaper per unit of aluminum than any corundum.

Jan 1, 1899

By H. Kenworthy, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2 with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite- type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore.

Jan 1, 1949

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give there full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: -

Jan 6, 1915

By JOHN MARKLE

JOHN MARBLE, mining engineer, coal operator, philanthropist, member of the Institute since 1879, vice-president in 1903-04, has been paid the well deserved tribute of Honorary Membership. The presentation of the diploma was made at a luncheon in New York on Feb. 13, the citation reading: "In recognition of his work as an engineer and administrator of mines and his services to mining engineering education." Within the last month Lafayette University dedicated the new John Markle Mining Engineering Building, the gift of the eminent alumnus for whom it is named. In addition, Mr. Markle has contributed a maintenance fund for the carrying out of far-reaching plans for improving the mining courses to be given at the Institution. One of his theories is that quality rather than quantity of engineering graduates is the need of the profession. John Markle was born in Hazleton, Pa., in 1858. He received his degree of M. E. at Lafayette in 1880, and married Mary Estelle Robinson in New York City in 1884. Since 1880 he has been associated continuously with the firm of G. B. Markle & Co., and its successor companies. He has also been an official of numerous other important companies, although he is now retired from active business life.

Jan 1, 1930

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,&apos; from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By CHARLES F. DEISS

The total pipe-line runs of petroleum in Indiana during 1945 were 4,114,000 bbl., a decline of nearly 17 per cent below the estimated 4,950,000 bbl. produced in 1944. Drilling activity during the year was centered in Posey and Gibson Counties, where seven new pools were discovered in the state. Four of the pools are in Posey County-Crunk, Farmersville, Jeffries and St. Wendells East-and the other three are in Gibson County-Johnson West, Lysle and Mt. Carmel East.

Jan 1, 1946

By HARRISON W. CRAVER

THE principal purposes of library-catalogs are to enable a reader to find a book of which the author, the title, or the subject is known; to show what the library has. by a given author, or on a given subject; and to assist in the choice of a book, as to its edition, or as to its character. The author, in a narrow sense, is the person who writes a book; in a wider sense it is applied to him who is the cause of the book&apos;s existence, e.g., editor, translator, compiler, etc. Bodies of men, societies, and countries are, from a cataloging point of view, con¬sidered the authors of their official publications, memoirs, transactions, etc. All names selected as author names are arranged in strict alphabetical order. A subject catalog fulfills its purpose by entering or registering each book under the name of that subject or topic of which the book chiefly treats. It may or may not be alphabetical in arrangement. If the arrangement is not alphabetical, the catalog is commonly called a classed subject catalog, although this name might with equal propriety be applied to some alphabetical arrangements.

Jan 1, 1920

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier&apos;s Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By Charles H. Foreman

IN JUNE 1921, the Sullivan &lining Co., owned jointly by the Bunker Hill and Sullivan Mining & Concentrating Co. and the Hecla Mining Co, started work on the development of the Star Mine. The development work contemplated called for a crosscut from the Hecla workings on the 2000 level to the Star ledge. The length of crosscut necessary to encounter the Star ledge was approximately 8900 ft. from the Hecla shaft. By using workings formerly made by the Hecla Mining Co., only about 8100 ft. of actual crosscutting was necessary. This crosscut has a direction of S 20° W and would have a tendency to crosscut any ledges in the intervening ground.

Jan 1, 1924