Search Documents

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By David Reddick

The mining industry is in the midst of dramatic change. Mining activities are moving from industrialized first world countries (Canada, Australia, and the United States) to the third world. This shift is occurring due to depleted reserves, tough environmental standards, and expensive labor in traditional mining countries. During a recent trip to South Africa, I was asked, owing to my educational background in economics and an international involvement in drilling and blasting, what changes could be anticipated in third world blasting practices as labor costs increase. It is from that beginning that this presentation has evolved.

Jan 1, 1997

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

Tonnage and grade are the principal reported components of mineral resource estimates but tonnage is a derivative of two more fundamental estimates; volume and bulk density. Typically, most of the effort in a resource estimation study is directed towards grade and volume, yet poor application of bulk density data to resource models can result in significant biases. The impact on tonnage estimates is easily recognised but poor density estimates may also introduce subtle biases into the grade estimates. Methods for measuring bulk density have been discussed previously. This paper focuses on the manipulation of bulk density data and the extension of bulk density from essentially point measurements to block estimates within resource models. Bulk density is a continuous, geologically controlled, spatial variable and should be treated as such. Issues such as combining data from multiple sources, sample support and the interdependence of bulk density and grade estimates must be resolved. The statistical and geostatistical techniques used for grade estimation are, under the right circumstances, equally applicable to bulk density. The importance of bulk density needs to be recognised. With robust raw data and correct estimation procedures, better estimates of bulk density can be obtained and both local and global tonnage and grade estimates can be improved.

Jan 1, 2000

A single aggregate mix design was developed based on a slag/Portland binder blend and crusher sand. The primary design criterion, after performance, was the fluidity of the shotcrete and concrete product to ensure compatibility with existing manufacturing and shotcrete equipment as well as the pipeline transport system Cullinan Diamond Mine was investigating. Initial work had determined an optimum slag/Portland to aggregate ratio while retaining a water to slag/Portland binder ratio of approximately 0.4 to maintain the flowability of the product. A super-plasticizer was used to further increase the flowability of the product as opposed to increasing the water content. Finally a polypropylene reinforcement fibre was included in the wet shotcrete product to improve the energy absorption characteristics of the shotcrete. Previous work on the strength development of the slag/Portland based shotcretes and concretes suggests that strength class based on the EN 206 specification is C40/50 while the toughness classification based on the EFNARC plate test is c, or greater than 1000 joules1. Typically, Cullinan Diamond Mine wanted a shotcrete with a uniaxial compressive cube strength of 45 MPa and an energy absorption, based on the EFNARC plate test, in excess of 700 joules. This is an EN 206 strength class of C36/45 requiring a uniaxial compressive core strength of 30.5 MPa and a toughness classification of b1. In addition to the shotcrete development, Cullinan Diamond Mine required concrete products with a compressive strength range of between 25 and 60 Mpa for differing construction operations underground to be manufactured from the same mix design and raw materials as for the shotcrete. Finally, Cullinan Diamond Mine carries out extensive dry shotcrete operations and an investigation into the possibility of using the single aggregate mix design for dry shotcreting was also entered into. This paper presents data that indicates that, under the terms of reference, a wet and dry shotcrete and concrete product appears to be possible from a single aggregate less than 6.7 mm in size, and that a slag/Portland binder is suitable for use as the hydraulic binder in all the products, and that the necessary performance parameters of strength and energy absorption can be achieved.

Jan 1, 2006

The resource industry must prepare for the inevitable shift towards automation as an operational objective. Although this may seem like a distant concern, many mining companies and equipment manufacturers are already conducting full-scale automation trials. The necessary technology is advancing at a rapid pace yet the training of people to support it at the trade level lags far behind. Those given the responsibility of installing and maintaining automated equipment in the mining environment require a unique set of skills and knowledge. These training needs demand attention to ensure that the wider uptake of automation is sustainable and achieves its full potential.   This paper documents work undertaken by CRCMining and the Mining Industry Skills Centre towards establishing a training framework seeking to address the needs of trade level personnel tasked with the support of automation equipment. A comprehensive definition of the skills and knowledge required by the hypothetical automation-specialised tradesperson is presented. The training pathway identified for these personnel is also described. This work forms part of the Mining Industry Skills Centre's Automation Skills Formation Strategy, funded by the Queensland Department of Education and Training.

Jun 1, 2010

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By T. R. Roy

A prediction model, developed by Central Mining Research Institute (India) for evaluation of fire risk rating of underground coal mine panels in bord and pillar working in respect of their proneness to spontaneous heating, is presented in this paper. The concept used in this model is innovative and user friendly. This model may be applied to a panel where extraction is carried out using any of the techniques: i) depillaring with formation of small pillars as final operation, ii) extraction by broadening of galleries, iii) depillaring with hydraulic sand stowing, and iv) depillaring with caving. Here, major fire risk parameters are short-listed and divided into three broad groups in accordance with the nature of their contribution to the spontaneous heating of a mine panel. The paper describes the procedure for estimating the fire risk rating of individual groups using separate objective type models developed for this purpose. Then it evaluates the overall fire risk rating of the panel by combining the fire risk ratings of all the three broad groups. The model is tested with the field data collected from different collieries spreading across the country and with the laboratory data for critical assessment of fitness. Keywords : prediction model, fire risk rating of panel, spontaneous heating of coal, underground panel, bord and pillar working.

Jan 1, 2003

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

The paper deals with the importance of design and of codes of practice in ensuring safe working conditions in mines. The design principles involved in the design process are dealt with, and the importance of a logical design process is emphasized. The links between the requirements for developing a code of practice, embodied in the existing guidelines for the preparation of such a code, and the design principles and process are considered in some detail. Finally, suggestions are included, which may provide improvements to the code and hence, ultimately, lead to further improvement in safe working conditions.

Jan 1, 2004

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By William Pitman

Ground instability and subsequent rock falls are a major concern in underground mines. As a result, several mining companies are conducting risk assessments of the ground support installed in their mines. Risk assessment is now commonly used to provide mine operators with a systematic process to assess the strategic risks that could lead to injury to personnel or loss of production, and evaluate possible risk control measures. Risk assessments can be carried out to identify major hazards, assess the likelihood of occurrence and consequences of each hazard and estimate the level of risk. This process allows assessment of possible remediation actions to minimize the risk and likelihood of occurrence or mitigation of the consequences to a level that is reasonable and practical. This paper presents two practical mine applications of qualitative risk assessment of ground support to highlight the benefits of this process. Yearly or bi-yearly risk assessment of mine excavations can assist mine operators in prioritizing resources and areas that require support remediation. In addition, it provides a mechanism for proactive response to reduce potential risks associated with personnel safety, equipment safety and environmental impact. It also provides a baseline against which changes in ground condition can be compared and quantified.

May 1, 2004

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006