Search Documents

Principles of management in ore preparation before process of enrichment of chrysotile ores are discussed. The formulas, which were tested in industrial conditions, are offered, which may be used for averaging of chrysotile-asbestos fibres by content in ore and grade.

Dec 6, 2010

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

Methods for Improving the Flotation Recovery of the Coarse Fraction of a Nickel Ore

Sep 13, 2010

By R. O. Pynnonen

This publication presents a study by the Federal Bureau of Mines of 494 accidents in open-pit iron-ore mines, beneficiation plants, and shops of the Lake Superior district from March 1949 to June 1956. These accidents caused 499 lost-time injuries, including 12 fatalities. A similar Bureau publication, Information Circular 7744, Analysis of 346 Accidents, Underground Iron-Ore Mines, Lake Superior District, was published in April 1956. Accident reports were analyzed by the Bureau to show the causes of in-juries and the unsafe practices or conditions that caused the accidents. Also shown are the time charges, times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 27 percent of the total number of disabling accidents that occurred in open-pit iron-ore mines, beneficiation plants, and shops in the district during the period covered. The text also contains tabulations of the accident experience and graphs with straight-line injury-frequency, injury-severity, and fatality trends for the period 1946-57.

Jan 1, 1959

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

Application of Natural Zeolite for the Removal of Diethylenetriamine (DETA) and DETA-Metal Complexes from Flotation Process Water

Sep 13, 2010

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey's success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By M. Fustic, A. H. Paul

The geology of the Muskeg River Oil Sands Mine is described to demonstrate how geologic modeling aided in resource evaluation and material characterization during the feasibility and construction stages. Bitumen is hosted in the clastic sediments of the Cretaceous McMurray Formation which is informally divided into members representing the fluvial, estuarine and marine environments of this transgressive sequence. Lithofacies mapping of drill core provides further detail to classify materials as resource type, for extraction suitability and for construction suitability. Geologic interpretation provides tools for the engineers to produce effective mine plans and for the operators to execute them during mine development.

Jan 1, 2002

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

Cokriging uses a sparsely sampled, but accurate and precise primary dataset, together with a more abundant secondary data-set, for example grades in a polymetallic orebody, containing both error and bias, to provide improved results compared to estimation with the primary data alone, as well as filtering the error and mitigating the effects of conditional bias. The method described here may also be applied in polymetallic orebodies and in other cases where the primary and secondary data could be collocated, and one of the data-sets need not be biased, unreliable, etc. An artificially created reference data-set of 512 lognormally distributed precious metal grades sampled at 25×25 m intervals constitutes the primary data-set. A secondary data-set on a 10×10 m grid comprising 3200 samples drawn from the reference data-set includes 30 per cent error and 1.5 multiplicative bias on each measurement. The primary and secondary non-collocated data-sets are statistically described and compared to the reference data-set. Variograms based on the primary data-set are modelled and used in the kriging of 10×10 m blocks using the 25×25 m and 50×50 m data grids for comparison against the results of the cokriged estimation. A linear model of coregionalization (LMC) is established using the primary and secondary data-sets and cokriging using both data-sets is shown to be a significant improvement over kriging with the primary data-set alone. The effects of the error and bias are filtered and removed during the cokriging estimation procedure. Thus cokriging using the more abundant secondary data, even though it contains error and bias, significantly improves the estimation of recoverable reserves.

Jan 1, 2014

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, III., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade fluorspar.2,3 Although fluorspar had been floated in Canada in 1921 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines6 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1947

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, III., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade fluorspar.2,3 Although fluorspar had been floated in Canada in 1921 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines6 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1947

By J. Lee, R. G. Rosehart

"The basic problem of arsenic contamination from mine water is discussed. Effective methods of removal involving chemical precipitation, activated carbon adsorption, ion exchange and reverse osmosis are discussed. As well as an economic analysis, detail is also paid to other ions in solution which are removed simultaneously.INTRODUCTIONThe object of this paper is to review arsenic and its removal from gold extraction plant effluents. The first method considered is chemical precipitation. A second method is sorption processes, such as ion exchange resins and activated carbon adsorption. A third method is the possible application of reverse osmosis for the treatment of mine waste waters containing arsenic.Arsenic pollution in the gold mining communities of Canada and Ghana have been extensively studies (l, 2). Lynch(3) Shabunin, Gutman and Kogan( 4), Hollo, Troth, Vennes and Illinigi (5) and Hau(6) have reported their removal methods of arsenic by chemical precipitation, ion exchange and biological methods. Their conclusions were that the precipitation with Fe2+ and Fe3+ ions was most effective.Scope of the ProblemInitial aspects of this research program involved a detailed analysis of the operation of a gold extraction plant located in Canada. The name and location of the mine is proprietary information. Figure 1 gives a basic process schematic with the main tailing streams identified.Table 1 gives information as to the various mine streams and their physical and chemical composition. In this study, primary attention is paid to the removal of dissolved arsenic from waste waters. Solids from this type of operation can always be back-filled. As could be anticipated, the dissolved As content of the primary flotation tailing stream is very low. The dissolved As level in the secondary processing stream and the roasting quench water is quite high. The reason being that at this stage of the process, the arsenic has been freed from the arsenopyrite forms."

Jan 1, 1972