Search Documents

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Louis J. Cabri, Donald Hoy

"Samples with contrasting gold mineralization were studied quantitatively prior to metallurgical tests. The AD samples are coarser-grained and characterized by abundant Sb minerals (jamesonite, berthierite, stibnite). The finer-grained MW sample has abundant pyrite and pyrrhotite, with arsenopyrite and galena next in abundance. A large number of gold mineral particles were determined by SEM investigation of hydroseparation concentrates, ranging from 150 to 597 per sample. The grain-size distribution of the gold minerals shows evidence of bimodal grain-size distributions (volume %), with the coarse fraction being most significant in sample MW-1 (maximum ECD=308µm). The coarsest gold minerals in the AD samples range from 139µm to 281µm ECD.The deportment of gold minerals is as electrum, aurostibite, native gold, and a possible new mineral (AuNiSb4). Gold also occurs in nisbite. The gold minerals are dominated by electrum in three samples and aurostibite is next in abundance. The major gold minerals are probably representative of three stages of gold mineralization. The first stage is represented by electrum, which is partly to completely replaced by Sb-rich mineralization forming aurostibite, and the last stage is native gold, often occurring as rims on one or the other earlier gold mineral. The gold minerals are strongly associated with sulphides in the AD samples (55 to 60 vol.%). At the grind used for the hydroseparation the liberated gold mineral quantity (volume %) is also significant, ranging from 65% for sample MW-1 to 30 to 37% for the AD samples.INTRODUCTIONThe Clarence Stream deposit is located 70 km south-southwest of Fredericton and 25 km northnorthwest of St. George, south-western New Brunswick, near the international boundary with Maine (Fig. 1)."

Jan 1, 2007

By Fidelis T. Suorineni

Rockbursts are a major hazard in deep hard rock underground mining and tunneling. To date a significant number of rockbursts still defy conventional explanations. A review of rockburst case histories in the literature has shown that pillars and tabular excavations under shear loading are prone to rockbursting in situations where they are least expected under conventional knowledge of rockburst causes. Despite the evidence of the effects of shear loading on underground infrastructure, and the frequency of their occurrence, little is known about how this loading mechanism causes such large magnitude events and extensive damage. In this paper analytical and numerical modeling are used to understand the behaviour of pillars and tabular excavations under shear loading. The numerical modelling results show that pillars under shear loading are less confined than their equivalents in loaded in pure compression in the same geologic environment, and are therefore more brittle and weak. For tabular excavations under shear loading, the behaviour depends on whether such excavations are continuous, co-planar or offset with rock bridges. Analytical results based on slit theory show releasable potential energy in tabular excavations increases nonlinearly with excavation half-span. The study results are important for the safe and economic extraction of orebodies under shear loading.

May 1, 2011

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By P. N. Anyalebechi

Keywords: Aluminum alloy 3004, Solidification rate, Homogenization, Second phase particles The effects of the fineness of as-solidified cast microstructure and temperature on the response of aluminum alloy 3004 to homogenization heat treatment (a.k.a. preheat) have been investigated. The study was conducted at 538oC and 595oC on directionally solidified laboratory-size ingots with a range of solidification rate of 0.10oC/s to 29.4oC/s. Optical and electron microscopy, quantitative image analysis, electrical conductivity, and electron probe microanalysis were used to quantify the effects of the homogenization heat treatment on the microstructure of aluminum alloy 3004. In general, increase in fineness of as-cast microstructure and homogenization temperature enhances the a-transformation reaction, dissolution of Mg2Si, elimination of dendritic microsegregation, and dispersoid formation. The homogenization heat treatment reduces the average size of second phase particles in castings solidified at <1oC/s. However, in castings solidified at above 1oC /s, homogenization causes the coarsening of the second phase particles. Mn in solid solution is independent of homogenization heat treatment temperature.

Jan 1, 2005

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By A Goldstone, T Maton

The Golden Cross Mine is located on the North Island of New Zealand, at the base of the Coromandel Peninsula, approximately 8 km northwest of Waihi. The project is operated as a Joint Venture with Coeur Gold New Zealand holding 800/0 and Viking Mining Limited with a 20% interest. The past open-pit and underground gold and silver producer has been in the reclamation phase of the operation for approximately 2.5 years and is now nearing completion. Although rehabilitation of the site is a regulatory requirement, the Closure Plan has been enhanced by the ongoing commitment of the Joint Venture to establish a sustainable land use for the site by commissioning engineered facilities designed to last for perpetuity. The Joint Venture identified six significant design features that were key to successful rehabilitation. These were the controlled placement of acid generating waste rock into engineered disposal sites; the design and placement of sealing layers over the waste rock disposal sites; the design and construction of diversion drains; the establishment and management of vegetation to protect the oxygen diffusion layer; a partial capping of the tailings to accelerate consolidation adjacent to the tailings dam embankment, and the implementation of a cyanide recovery circuit to recycle cyanide from the tailings prior to disposal. Another key to success for the project involved genuine consultation with all parties participating in the planning, evaluation, and consenting of the closure process at Golden Cross. The local and regulatory community has been widely represented in the Joint Venture&apos;s operating and closure plans throughout the history of the mine. Participants include: Regional and District Councillors and staff members, professional peer reviewers, environmental groups, local residents of the valley, and Iwi. This overall commitment to the project has resulted in a world-class rehabilitation program for the first modern metal-mine closure in New Zealand and we believe that collectively, the work done at Golden Cross is helping to set a standard for the success of future programs within the extractive industry.

Jan 1, 2000

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By S. Pule, Z. Ndabezimbi, A. Hefer, E. Cupido

This article outlines various projects implemented at Rand Refinery to reduce effluent generation and freshwater consumption. The refinery generates about 2800 m³ of effluent annually and has initiated projects such as granulation water recycle and silver leach optimisation to address these issues. The granulation water recycle project has successfully reduced effluent volumes, while the silver leach optimisation has further decreased effluent by implementing stoichiometric addition of HCl and NaClO3. The vibratory shear enhanced processing (VSEP) trial showed promising results for gold recovery from wastewater, though further trials are recommended. The water savings of the effluent reduction projects are monitored by measuring the amount of effluent pumped to service yard effluent storage facilities with the use of flow meters connected on SCADA. Since the effluent reduction initiative of granulation effluent recycle in FY23, the effluent reduced to 2676 m³. In FY24, the stoichiometric addition of HCl and NaClO3 was implemented in the silver leach process, further reducing the effluent to 2083 m³.

Mar 5, 2025

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By E. Chin

The domination of Bangladesh&apos;s mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation&apos;s foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By P Allen, E Gleeson, D Boakye, R Chesher, S Konopa

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Not only do epithermal gold deposits provide many challenges in estimating mineral resources, the complexities of these deposits also provide technical challenges in assessing appropriate mining and processing strategies, as well as social and environmental planning and management. The characteristics of epithermal gold deposits include being highly variable with respect to geometry and gold grade distribution, the presence of other economic contributors, mineralogy, texture, rock strength, weathering and alteration overprint. These characteristics influence the economic value of mining projects in an interlinked manner. Consequently, successful exploitation of epithermal deposits requires a holistic approach, coupled with the effective integration of geological data to meet all aspects of mine development decision-making. This paper presents examples of the key technical challenges encountered in estimating and mining epithermal deposits. It also highlights why these issues need to be addressed from the viewpoint of geology, sampling, resource estimation, mine planning, mineral processing and social and environmental planning for the true value of the mining project to be realised.CITATION:Konopa, S, Chesher, R, Gleeson, E, Allen, P and Boakye, D, 2015. Challenges in maximising the value from epithermal gold deposits, in Proceedings PACRIM 2015 Congress, pp 127–132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015