Search Documents

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

For the third successive year it appears that demand for platinum will exceed supplies of newly-mined metal, forecasts Johnson Matthey in its "Platinum 1987 Interim Review." Based on data available at the end of August 1987, Johnson Matthey estimates that western world demand for platinum could exceed 93t (3 million oz) for the first time ever in 1987. Given a likely increase in demand of 4.3t to around 94t (140,000 oz to around 3.02 million oz), up by about 5% over 1986, there would be a 1.8- to 2.2-t (60,000- to 70,000-oz) shortfall in 1987 supply. South African mines enjoying undisrupted production last year after strikes affected Impala's output in 1986. The rate of increases in western world supplies, though, has probably not kept pace with the growth in demand. A downturn in US demand for platinum was counterbalanced by substantially increased purchases from Japanese and Western European consumers of the metal. Total imports of platinum into Japan in 1987 may have reached a record level of 45t (1.45 million oz). The largest source of demand for platinum remains its use in autocatalysts US and Japanese auto manufacturers reduced their platinum purchases in the wake of falling car production. Therefore, a small decline in overall 1987 sales of perhaps 780 kt (25,000 oz) was expected in 1987. Western European demand, however, rose strongly as a result of increased output. The spread of exhaust emission control regulations has sharply boosted the number of cars equipped with three-way catalysts containing platinum and rhodium. Western European auto makers probably needed 5.6t (180,000 oz) of platinum last year, a 50% increase over 1986. The jewelry industry, the second largest user of platinum, increased its offtake of platinum in 1987. Japan, the key to the jewelry industry's consumption of platinum, could absorb 24.8 to 26.4 (800,000 to 850,000 oz) in 1987, compared with 23t (740,000 oz) in 1986. Platinum has wide and diverse applications in industry. Other major users are the chemical, glass, electronics and petroleum industries. They were expected to increase their aggregate demand by about 1.8t (60,000 oz), or 11% in 1987. Investment demand for small platinum bars and coins of up to 311g (10 oz) dropped back in relatively inhospitable conditions. This, after rapid increases in recent years and a surge in US demand in 1986. However, Japanese investors purchasing bars weighing 500g or 1 kg (16 to 32 oz), and considered more speculative, recovered last year. Over the first eight months of 1987, platinum performed strongly on the open market with average prices well up from 1986 in dollar terms. But the increase was less marked where measured in sterling or yen. Platinum ad¬vanced by $3.70/g ($115 per oz) between Jan. 1 and mid-September with the average price having been surpassed only in the heady days of 1980. Johnson Matthey believes that supply and demand appear likely to keep more or less in step on a gently rising path. The recent open market volatility will continue with prices fluctuating widely over short periods. Writing in mid-September, and basing its view on the tangible evidence of platinum's price fall since the review was written, the company's assessment of price prospects is unchanged. Demand for platinum remains strong all-round. In October, imports of platinum into Japan were exceptionally high. And in the US and Japan there was a marked resurgence of demand from private investors. Although market sentiment may have been influenced in part by the news of several potential new platinum mines in South Africa, the full effects of these prospects on supply, even if they were all to materialize, would not be felt before the early-mid 1990s, Johnson Matthey said. According to the review, no radical change in platinum supplies is discernible in the near-term. Incremental growth from South Africa can be expected as the major producers continue to make the most of their existing resources. The Soviet Union may be keener to sell than it appeared earlier in 1987, especially if prices hold up, but a substantial increase is improbable. Canadian supplies are not capable of much variation from present levels. The palladium-rich Stillwater mine will make a modest contribution. Referring to the investment market, Johnson Matthey concluded that despite this year's reduction in sales of small-denomination investment products, platinum does appear to have established itself with private investors. Bearing in mind how business multiplied in comparatively unfavorable conditions before 1986, it is reasonable to look for a resumption of growth once the climate improves.

Jan 2, 1988

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By João Paulo Ferreira Santos

Neste trabalho foram obtidos nanocompósitos híbridos constituídos por nanotubos de carbono de paredes múltiplas (MWCNT) e por nanofibras eletrofiadas de nylon 6 em uma matriz epoxídica. Os MWCNT foram funcionalizados com grupamentos carboxílicos e dispersos através de ultrassom na resina epoxídica. A composição resultante foi disposta de maneira alternada com mantas de nanofibras de nylon 6 para formar estruturas compósitas na forma de sanduiches, as quais foram termicamente curadas. Medidas de resistividade elétrica das estruturas obtidas mostraram que uma percolação elétrica entre 0,05% e 0,5% (v/v) de MWCNT foi alcançada. Do ponto de vista mecânico, a incorporação de MWCNT na matriz epoxídica resultou em aumentos de módulo de elasticidade (26%) e na resistência a ruptura (19%), porém, devido a presença de aglomerados de nanocargas, a deformação na ruptura e a resistência ao impacto foram severamente reduzidas para 71% e 33%, respectivamente. Por outro lado, a adição de nanofibras de nylon 6 para formar um híbrido, mostrou-se, bastante promissora ao levar a aumentos de 8% na resistência ao impacto sem ocasionar perdas de módulo elástico, na resistência à ruptura e na deformação na ruptura.

Aug 8, 2018

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By Camila Lourenço Soares

A produção de aço no mundo está a cada dia mais competitivo, com isso as indústrias siderúrgicas tem desenvolvidos projetos com foco na melhoria da qualidade dos aços e na redução dos custos dos processos de fabricação. Este trabalho descreve as melhorias realizadas no processo de lingotamento contínuo, com foco na redução do desvio de placas por desobstrução dos veios da MCC 2. Esta melhoria consistiu na modificação do sistema de controle e injeção de argônio dos veios durante o lingotamento. A implementação dessas ações propiciou um melhor controle na injeção de argônio no sistema de válvula gaveta, reduzindo significativamente as obstruções do veio por deposição de alumina. Hoje, com os resultados alcançados na MCC 2 perduramos entre as melhores práticas nacionais. O trabalho foi realizado sem investimento contribuindo com a redução do custo de transformação do aço em placa.

Aug 16, 2017

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By Arthur V. Petty

In Bureau of Mines research on recycling chrome-containing refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated. By means of dry magnetic separation on minus 6-mesh crushed wastes, a concentrate was produced. After minor adjustments to the particle size distribution, full-size refractory brick were dry-pressed by a commercial producer and fired to 1,450° and 1,730° C. Standard testing procedures were used to determine the cold-crushing strength, modulus of rupture at 25°, 1,300°, and 1,500° C, hot load, thermal shock resistance, thermal expansion, and slag resistance. Optical and electron microscopy were used to determine grain-bonding mechanisms, and energy-dispersive analysis of X-rays was used to determine elemental distribution. The test results indicate that the beneficiated material could be used to produce a refractory product suitable for moderate-temperature applications.

Jan 1, 1982

By Juan Languasco de Habich

El presente texto señala la situación actual de la pequeña minería, así como las ventajas, decreto ley 18880, garantía, reservas, requisitos, características del financiamiento, crédito minero, rol de tasa, modalidades del crédito minero, y las fuentes de financiamiento para la pequeña y mediana minería.

Sep 1, 1979

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By James S. Browning

Recovery of fine mica from a sample of impounded tailing from the Dixie Mines, Inc., crushing and screening operations, Heflin, Ala., was investigated to determine if plant losses of mica could be reduced while econmically producing a commercially acceptable mica concentrate. Conventional wet-tabling and agglomerate-tabling methods yielded concentrates assaying about 95 percent mica from the tailing that contained 17 percent mica. Products containing about 98 percent mica and accounting for mica recoveries of 86 percent were obtained by flotation, using as reagents sulfuric acid, kerosene, and coco amine acetate (a mixture consisting chiefly of dodecyl and tetradecyl amine acetates). The results of the batch flotation tests were verified by tests in a small continuous flotation pilot plant.

Jan 1, 1963

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By Marcella Gautê Cavalcante Xavier

A presente proposta tem por objetivo desenvolver uma análise experimental da liga hipereutética Sn-0,5%Ni solidificada unidirecionalmente em regime transitório de fluxo de calor contra chapa molde de cobre. A liga foi avaliada quanto a sua microestrutura bruta de fusão e suas respectivas correlações com os parâmetros térmicos (velocidade da frente eutética -VE e taxa de resfriamento eutética -?E) e propriedades mecânicas. Os resultados mostram que a morfologia microestrutural predominante é composta por células ricas em estanho (β-Sn) circundadas por mistura eutética Sn+intermetálico tipo NiSn. Uma transição microestrutural foi observada entre as posições 15mm (?E=1,7°C/s) e 30mm (?E=1,1°C/s), de célula regular (CR)?célula tipo placa (CTP). Notou-se ainda a presença de intermetálicos primários NiSn distribuídos ao longo da matriz nas posições iniciais do lingote. Valores superiores de limite de resistência à tração (σu=26 MPa) e limite de escoamento (σy=21 MPa) foram encontrados para a posição 6mm a partir da base refrigerada do lingote, podendo estar relacionados com a estrutura celular mais refinada e também com a presença dos intermetálicos primários NiSn. O alongamento específico (?) comportou-se de maneira inversa, visto que as estruturas mais grosseiras (CTP) e a ausência de intermetálicos primários são responsáveis por facilitar a deformação plástica na estrutura da liga Sn-0,5%Ni, aumentando seu nível de ductilidade.

Oct 30, 2017