Search Documents

By E. C. Tarpley

An acid-extraction procedure developed in Germany for determining mineral matter in coal was investigated by the Bureau of Mines to determine its application to American coals. It was found to be suitable for all ranks of coal from anthracite to lignite if modified slightly for coals containing considerable quantities of calcium compounds, such as calcite or calcium humate. The precision of the method is satisfactory, and the results are probably closer to the true content of mineral matter than those obtained by empirical formulas. The method requires considerably more analytical data than the Parr or approximation formulas but is no more time consuming than obtaining the necessary data for the King, Maries, and Crossley formula (theoretically the most comprehensive empirical formula used). An appendix to this report includes a detailed description of a recommended procedure.

Jan 1, 1959

By D. J. R. Ras

A sub-level open stoping method is being used to mine the massive deposits at TARGET Gold Mine which uses cemented tailings to backfill the stopes. This requires the construction of bulkheads to contain the freshly placed backfill, capable of resisting the hydraulic pressure imposed by filling. The bulkheads must contain an 8 metre head of backfill slurry within 48 hours and withstand the force exerted by a 35 metre load of consolidated fill at a maximum estimated fill relative density of 1.9. After a variety of methods of construction were evaluated, it was decided to construct the bulkheads using the low density, fast-setting foamed cement-based product TEKSEAL HS manufactured by MINOVA RSA. The cement foam is contained between low-cost steel and fabric brattices which are easy to construct, using a method specially developed for the TARGET bulkheads. The paper will describe the design, trialling and construction of the bulkheads, and results obtained to date.

May 1, 2007

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By Glen Mc Gavigan

The roof of the Sishen cave is being mined in order to exploit 6.8Mt of high grade ore. The cavity is filled with quartzite backfill in order to support the roof in the event of collapse. The cave dips at approximately 37o, is 260m along dip and 70m along strike and has a total volume of 261,391m3. GPS and optical monitoring techniques were attempted to detect subsidence but proved to be impractical. The GroundProbe Slope Stability Radar (SSR) uses differential interferometry to measure sub millimetre movement in a rock face. The SSR was applied in a non production situation and detected subsidences of 38mm/day before visual signs of instability were detected. The rate of deformation detected was slowing as a result of the roof coming to rest on underlying backfill. Monitoring during production drilling detected a sudden subsidence of 18.6mm/hour which resulted in the evacuation of personnel from the area. Further inspection of data showed that the rate of deformation was slowing and production was allowed to continue without further incident. The SSR has helped dispel the fears of workers and has proven that subsidence can be accurately measured and delineated with the SSR.

Jan 1, 2006

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By V Morand, W R. H Ramsay

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (D1) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with D1 and the plunge of the F1 fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late D1 . d18O values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By D. J. Hutchinson, M. Lato, M. Diederichs

Light Detection and Ranging (LiDAR)-based applications for geomechanical purposes have recently proven to be a highly reliable and accurate form of remote analysis and documentation. The ability to remotely collect, process and evaluate rockmasses for structural geomechanical applications has benefits ranging from safety to efficiency, and provides a permanent record that can be assessed before and after an excavation has been completed. With the collaboration of Queen’s University and Rio Tinto, the Iron Ore Company of Canada (IOC) mines in Labrador City, Newfoundland and Labrador, evaluated the practical application of the I-Site 4400 LiDAR equipment, in conjunction with the Vulcan geotechnical module for geomechanical purposes. The project provided a comparative analysis between conventional hand-mapping and digital analysis. The analysis indicates that digital mapping could be employed as an active tool within the general geotechnical workflow, where results would be used in pit wall and rockmass support designs. As well, the field work enabled the generation of effective operational guidelines and protocols to maximize scanning efficiency.

Jan 1, 2009

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

Electroosmotic Dewatering and Consolidation of Mineral Waste Tailings

Sep 13, 2010

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009