Search Documents

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Jess Harding

Oyu Tolgoi investment agreement now in full, legal effect Successful completion of a series of conditions to 2009 Investment Agreement was announced March 31, 2010. Full-scale construction now set to begin. First copper-gold commercial production from Oyu Tolgoi expected in 2013. 34% of holding company Oyu Tolgoi LL Cacquired by Erdenes MGL, a Mongolian state-owned resources company. Remaining 66% will continue to be owned by Ivanhoe Mines. ?After 9 years of discoveries at Oyu Tolgoi, a big piece of the future of copper and gold in Asia is poised to become a reality.?

May 1, 2010

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By D Craw, G Eis

Late Cretaceous Blue Spur Conglomerate preserved as isolated remnants at Gabriels Gully, Weatherstones, Forsyth, Waitahuna Gully and Adams Flat was deposited during the intiation and early stages of extensional movement on the Tuapeka Fault zone at each locality. The deposits represent successive courses of a single fluvial system flowing across the Tuapeka Fault zone from the up-thrown (northeast) block. Each course, beginning with the channel at Gabriels Gully, was abandoned as a result of uplift-induced defeated antecedence in favour of a new course farther to the southeast around the southeast-propagating tip of the Tuapeka Fault zone. Schist and quartz in the conglomerate was derived ultimately from schistose rocks northeast of the Tuapeka Fault zone. Caples Terrane greywacke detritus in the middle and upper beds of the conglomerate was probably recycled from pre-existing sedimentary cover on the up-thrown block, following initiation of uplift on the Tuapeka Fault zone at each locality. Most of the gold is derived from vein sources in Otago Schist rocks to the north, and/or associated placers. Hydrothermal veins at Waipori, Hindon, Barewood, and Macraes are the most likely primary sources. There is no evidence to support previous interpretations of deposition by river systems flowing from the southwest, or axially along the Tuapeka Fault zone from northwest to southeast. High gold grades within Blue Spur Conglomerate should have a linear trend more or less similar to the orientation of the host channels, but are likely to drop off rapidly to the southwest. Extensions of the conglomerate-filled channels are unlikely to be preserved, but there is a strong probability that younger placers recycled from the former channels exist.

Jan 1, 1999

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational 'silos', inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

With increasing demand for real-time monitoring of mine parameters, the requirement for appropriate data management in many mining applications is also increasing. This includes atmospheric monitoring in underground coal and metal mines. Although a number of different (real-time) monitoring systems have been installed in underground mines, they all typically share the same systems or sub-systems, where each sub-system may include both custom hardware and / or software components. In addition, monitoring components installed in underground coal mines in the USA should also be intrinsically safe and approved by the US Mine Safety and Health Administration. Real-time analysis adds complexity to the system since data validation and storage should be completed independently of filtering, data reduction operations, or visualization. Real-time processing may include statistical evaluation, trending, cross-correlation, and real-time alarm or warning generation. This paper presents the concept and design of an integrated system under development for atmospheric monitoring in US coal mines.

Jan 1, 2014

Removal of As(III) and As(V) in Aqueous Solution There are toxic arsenical species such as As(III) and As(V), and arsenious species have specially strong toxicity. The strong toxicity causes contamination of groundwater and water pollution for the semiconductor production process. This study is concerned with the removal of As(III) and As(V) with various kinds of Mg/Al layered double hydroxides (LDH) containing CO32-, SO42-, Cl- and NO3- as interlayer anionic species. The anion exchange property is different from the kind of layered double hydroxides and the Mg-Al-NO3-LDH is superior in the anion exchange property of As(III) and As(V) due to the nature of nitrate ion existing in the interlayer. The pH condition suitable for As(V) removal is 7.1 or more. If the initial conditions such as 10mg/dm3 of As(V) concentration, 7.1 of pH, 1 m3 of amount of solution and 99 per cent of removal are fixed, the required amount of Mg-Al-NO3-LDH is 0.27kg for two step-batch operations. The As(III) is suitable to oxidize to As(V) before the removal processing.

Sep 13, 2010

By Roussos Dimitrakopoulos

Conventional approaches to estimating reserves and optimizing mine planning and production forecasting result in single, often biased forecasts. This is largely due to the non-linear propagation of errors in understanding orebody attributes from a limited finite number of drilling data, throughout the chain of mine planning and mining. A new mine planning paradign is considered herein to include two interacting and potentially fusing elements: stochastic simulation and stochastic optimization. These two elements provide an expanded mathematical framework that allows the modelling of orebody uncertainty and its direct integration to mine design, production planning and valuation of mining projects and operations. This stochastic framework has shown to increase the value of production schedules in the order of 25%. In addition, case studies show that stochastic optimal pit limits are about 15% larger in terms of total tonnage, compared to the conventional (deterministic) optimal pit limits. This difference extends life of mine and adds approximately 10% of net present value (NPV) to the NPV reported above from stochastic production scheduling within the conventionally optimal pit limits. Furthermore, results suggest a potential new contribution to the sustainable utilization of natural resources.

Oct 1, 2009

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By B Xiao, J Yang, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tuwu-Yandong Cu deposit, located in the East Tianshan mountains in the eastern section of the Central Asian Orogenic Belt, is the largest and economically most important porphyry Cu deposit in Xinjiang, China. It contains ~3 Mt of copper at an average grade of 0.46 per cent Cu and 0.2 g/t Au, with significant amounts of Mo and Ag. The deposit is mainly hosted in the Carboniferous Qi’eshan Group and plagiogranite porphyry, and is controlled by faults that are east–west-, north-west- and north-east-trending. Ore minerals in the Tuwu-Yandong deposit are dominated by pyrite, chalcopyrite and molybdenite, with minor bornite, chalcocite, magnetite, sphalerite and galena. Gangue minerals are mainly composed of quartz, sericite, chlorite, epidote, anhydrite, gypsum, muscovite, biotite, phosphorite, sphene, dolomite, actinolite, barite, albite and calcite. Based on the megascopic and microscopic textural relationships and mineral assemblages, five stages of hydrothermal alteration and hypogene mineralisation are recognized in the Tuwu-Yandong Cu deposit: the potassic stage, propylitic stage, phyllic stage, late veins stage and supergene stage. Most of the copper was deposited during the phyllic stage, along with less molybdenite.CITATION:Xiao, B, Chen, H, Wang, Y and Yang, J, 2015. Geology, mineralisation and alteration of the Tuwu-Yandong porphyry Cu deposit, north-west China, in Proceedings PACRIM 2015 Congress, pp 641–644 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015