Search Documents

Cook Colliery currently mines in the Argo Seam, beneath old workings in an overlying seam. The Argo seam is up to 4.8 m thick and a continuous haulage system behind an ABM25 is used to develop first workings. Current partial secondary extraction utilises floor stripping and pocketing or sumping first working pillars on retreat. The following paper summarises this recent secondary extraction experience, particularly from a geotechnical perspective, but also considering production and ventilation issues. Outcomes and learnings are presented for mining in this challenging and close multi-seam environment. The sealed castor seam workings are within 20 m, and vary from unmined areas to large first working pillars, to partial extraction panels and full extraction panels. High stress remnant pillars and goaf-edges are notable mining considerations. The mining environment is further complicated by faulting, thrust zones and weak laminated roof.

Nov 25, 2010

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By Nicholas Adrian Barcza

"What affects and influences one’s perspective of the mining and metallurgical industries?One’s perspective of the industry we work in changes over time as a function of our experience as well as from the interaction we have with colleagues locally and probably even more so with those internationally. Furthermore, the ever-changing environment continues to impact the context in which one sees things. Living mostly in South Africa through its changes in the past fi fty years but also having the opportunity to travel extensively and work on projects abroad adds an invaluable richness to this more global perspective. One of the greatest challenges is how best to use this experience to endeavour to support the many potential opportunities in southern as well as sub-Saharan Africa. However, one has also to face the realities of how the best interests of the country and its peoples are sadly often not well served for various unfortunate reasons. Investment, education, regional stability, and good governance are some of the most critical considerations for the prosperity and survival of the region.The mining and metallurgical industry in southern and sub-Saharan Africa changed significantly during the post-colonial and apartheid eras as a result of global and regional developments that have impacted the ownership of businesses, the technologies used, and products produced in a manner that was not envisaged even fi fty years ago. Southern Africa’s mining and metallurgical industry has progressed from one based mostly on diamonds and gold in the late 19th century to a much more diverse one that involves the production of a variety of other precious, base, and ferrous metals and minerals as well as coal and industrial minerals. The infrastructure and manufacturing capacity was largely developed to meet the needs of this industry during its growth phases, but even though the dynamics have changed there is still a need for more efficient and effective support systems in the region."

Jul 1, 2019

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By J. Chai, H. H. Sedarat, Gary J. E. Kramer, A. Kozak

Precast concrete segmental lining systems have been gaining widespread use in seismically active areas and a single-pass version of such a system has been developed for use on the Silicon Valley Rapid Transit (SVRT) Project in San Jose, California. The response of tunnel linings to seismic shaking is often predicted using engineering judgment, elastic closed-form solutions and numerical modeling. Such analyses generally assume a continuous structural system and hence do not explicitly model the behavior of the jointed segmental lining. A number of analyses were performed to predict radial and circumferential joint behavior during seismic ovaling and wave propagation. These analyses included a complex, three-dimensional finite element based ground-structure interaction model that incorporates inelastic constitutive soil behavior, cracked concrete properties and no-tension, frictional segment joint surfaces. The paper discusses the results of the analyses and provides guidelines for the design of precast systems in zones of high seismicity.

Jan 1, 2007

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988

By D. M. Doyle, P. J. Hannon

"The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) is a subsidiary of a five-year Economic and Regional Development Agreement, signed on June 11, 1984. The objectives of the M.D.A. are to strengthen and diversify the Nova Scotian mineral industry and to coordinate federal and provincial policies and programs. The agreement outlines the activities and responsibilities of each government, including the division of the cost (60:40, federal: provincial) between governments. The agreement established a framework for joint planning to avoid overlap or duplication of programs.The M.D.A. programs are broadly divided into five sectors (Table 1 and Fig. 1): Geoscience, Minerals Technology, Development, Firm Specific and Public Information. Each sector is administered by a subcommittee composed of one federal member and one provincial member. The subcommittees report to a Management Committee. The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) Management Committee is made up of Dr. Jack Reeves from EMR and Dr. Richard Potter from the NSDME.The Geoscience subcommittee, co-chaired by Peter Giles (NSDME) and William Poole (EMR), manages the regional geologic, geochemical and geophysical studies in the province. Included in this sector are studies into mineral deposits and the basic geological relationships between mineral deposits.The Mineral Technology sector is co-chaired by the authors, Don Doyle (CANMET) and Pat Hannon (NSDME). This sector of the M.D.A. conducts studies into mineral processing, sampling, deposit byproduct commodities and project feasibility analysis."

Jan 1, 1987

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010