Search Documents

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By Douglas B. Silver

Traditional cycle theory would postulate that if you have a supply shortage relative to demand, the price will increase because buyers will incrementally increase the price they are willing to pay to ensure that their needs are fulfilled. As prices rise, more supply will be brought on and will eventually exceed demand. This supply excess will cause the price to decline as producers have to lower their prices to sell their goods. What is interesting is that cycles are simply volatility over time. Without the time factor, volatility simply goes up and down. When we add the time element, a cycle is created. This cycle can be big or small. In mining?s case, we are talking about a Super Cycle ? a big cycle. But a Su-per Cycle can be formed in two ways. It can form by either increasing the wavelength or the volatility. If these two elements are combined, a Super Cycle is formed. It is bigger than the normal cycle in terms of time duration and extent of volatility. A recent study (Fig. 1) conducted by Cuddington and Jarrett showed an interesting proof of Super Cycles and suggests that these cycles last between 15 and 30 years. So, what causes a Su-per Cycle? Is it a convergence of unrelated events or a consequence of related events? In a global community everything is related. Equilibrium theory would also take the position that a Super Cycle is a consequence of events.

Jan 1, 2008

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By M. Nete

Qualitative analysis of three mineral samples from northern Mozambique was accomplished by X-ray diffraction (XRD), microscopy, scintillation, and magnetic determination. Chemical characterization was accomplished using ICP-OES and pressed powder XRF after dissolution using microwave-assisted digestion and flux fusion. The samples consisted of a mixture of minerals with tantalite as the major component, with minor amounts of microlite, quartz, mica, accessory garnet, and tourmaline. Incomplete dissolution was obtained using microwave digestion, with maximum recoveries of 90.25 ± 0.06% and 88.90 ± 0.04% for Nb2O5 and Ta2O5 respectively. Complete dissolution using Li2B4O7 resulted in recoveries of 98.5 ±0.2% Nb2O5 and 100.4 ± 0.3% Ta2O5.

Jan 1, 2012

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By David R. Macedon

"Through the years, a wide variety of dust control methods have been utilized at mineral processing operations. While some have been successful, many have been highly ineffective. Dust Control systems currently in use include baghouse systems, fog systems, surfactant spray systems, and foam dust suppression. While baghouse systems can be effective, they are capitalintensive and costly to operate and maintain. Chemical dust control programs can be very effective. However, if applied incorrectly, they can have detrimental effect on mineral recovery. Thus, many operations utilize a combination of baghouses and water, often with limited success.Recent advancements in surfactant and polymer chemistry have resulted in substantially improved chemical dust suppression programs. These products range from non-corrosive surfactant/humectant combinations for road dust control to foam-based systems for crushers and transfer points, to advanced polymers for pile binding and soil stabilization. These advances are discussed in detail, citing results from fieldwork in the precious and base metals industries.INTRODUCTIONThe global nature of the mineral processing industry presents a unique set of challenges. Traditional thinking would tell us what works in one place should work in another. This could not be further from the truth in the area of dust control. We learn very quickly that there are a number of factors that can affect the efficiency and success of a dust control program and that these factors are not all chemical or equipment related. Some of these factors include facility maintenance, product selection, water quality and characteristics, and economic considerations.What has been learned from past experience is that each mineral processing plant presents a unique set of factors that will affect the ability to create an optimal dust control program. This paper presents a myriad of treatment options that will highlight the advancements in chemical dust suppression products and equipment."

Jan 1, 2004

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By Daniel Roy

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc. patented gassed emulsion technology, is summarized in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimize the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2003

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By W P. Player

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision.   The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand . In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand , these matters will all be addressed in what are referred to as 'minerals programmes'.   The Crown Minerals Act 1991, which is the legislation governing the allocation and management of permits for Crown owned minerals, requires that the Minister of Energy prepare minerals programmes. Minerals programmes establish the policies, procedures and provisions that the Minister shall follow in exercising his or her functions and powers under the Crown Minerals Act. Minerals programmes set out the principal reasons for and against adopting these policies, procedures and provisions and also restrictions on prospecting, exploration and mining for Crown owned minerals. Essentially minerals programmes define the mining regime for the minerals to which they apply, other than the taxation regime, environmental and health, safety provisions, land access matters and general matters concerning the investment climate.

Jan 1, 1995

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012