Search Documents

By X. Louw

"This paper examines the change in surface properties of the Polyurea used on spirals at different operational times: unused spiral, 28 months in operation and 58 months in operation. This is being done to investigate the alleged statement that spirals have a decrease in spiral separation efficiency after a certain period of operational time. Observing the surface characteristics under 1.5x and 36x magnification it can be concluded that the surface roughness decreases with increased operational time. This may be explained by a decrease in air inclusions and streak lines as the spiral surface wears. Decreased surface roughness should in theory have a beneficial effect on spiral separation performance. This leads to the conclusion that if a decrease in spiral separation performance is observed after a certain period of operation, it can’t be attributed to the change in surface properties. Uneven wear of the spiral surface, material creep or application of force to the spiral will change the profile of the spiral and could cause an adverse effect on spiral separation performance. The metallurgical test work showed that the best results are obtained at 30 - 35% solids by mass in the spiral feed. The iron recovery was significantly higher in the new spiral in comparison to the 2012 and 2010 spirals. The mass yield to concentrate in the new spiral was approximately three times more than for the older spirals. In conclusion, the yield combined with the grade, which equals the recovery was the best for the new spiral.IntroductionAn investigation was launched to research the common belief that spirals experience a decrease in efficiency, and therefore recovery, after a certain period of operation (a period of seven years has been used in the industry). The properties of the spiral that may have an effect on the efficiency are:"

Jan 1, 2017

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By N. I. Aziz, I. Tague, P. Mackenzie-Wood

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Feb 24, 1997

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Russell R. Trengove

The largest potential reserves of manganese in Nevada are in the Pioche district. To date, these large reserves of 10-to l2-percent manganese cannot be upgraded economically. Other large, low-grade deposits, such as the Virgin River and Boulder City deposits in Clark County, cannot be considered immediate sources of manganese. Reserves of the principal manganese deposits in Nevada, based on the most reliable estimates, total about 17 million tons analyzing 7.6 to 13.6 percent manganese. Most of the deposits are of a type that cannot be prospected systematically but have been prospected and developed in the course of productive mining operations. To realize production from low-grade deposits that are amenable to concentration, a ready market must be provided. Thus far, Government stockpiles have been the major outlet for these low-grade ores. Research and experimentation over a period of years have led to development of several processes technologically applicable to these low-grade ore bodies, but their economics is not sufficient to allow competition with imported ores on the open market.

Jan 1, 1959

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

The quantity, quality and detail of project information increases as project development moves from initial scoping level studies, to pre-feasibility and option studies, then definitive feasibility study and basic engineering stages. Data accumulates from metallurgical and vendor testing from various ore types and composites carried out to assess physical characteristics and processing responses of the ore. Over-simplification or assumptions about the orebody for flow sheet development can result in using æaverageÆ information for design. Use of averages of data can have adverse implications on sizing of plant and equipment and consequently on definitive study cost estimates and detailed engineering. In practice, the treatment plant workforce is faced with managing a non-homogeneous or non-average orebody in a variable operating environment that is not always predictable. This paper presents views on how to use the data generated from testwork in project development and for process and plant design. Examples of process design risk or operating risk are presented. Although this topic is applicable to the broad range of process design decision making in the minerals industry, this discussion references comminution, flotation and extraction processes for gold and base metal ores.

Jan 1, 2004

Single particle breakage tests have been used by a number of researchers to investigate some salient features of the complex comminution process. The characteristics of the common single particle breakage tests such as single impact, double impact and slow compression tests are examined and the results from these tests are compared. A comparison of the results from single particle breakage tests with grindability and ball mill tests is given. Application of the results from single particle breakage tests to modelling industrial comminution processes is described. The necessity for further research into single particle breakage tests to develop a simple but comprehensive technique for estimating the breakage characteristics of ores is discussed.

Jan 1, 1986

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By John E. Tilton

Real copper prices during the past several decades display two striking characteristics. First, they are highly volatile. Within a year or two, copper prices can rise or fall by 30% or more. Second, over the longer term, they are falling. Indeed, since 1970, the secular trend price for copper is down by more than 50%. Figure 1 highlights both of these characteristics. It shows the average annual US producer price for copper since 1970 measured in constant 2001 US dollars. While the London Metal Exchange (LME) copper price is not shown, it and the US producer price have for some time moved more or less together. So pronounced short-run fluctuations around a significant long-run decline describe copper prices, not only in the United States, but around the world.

Jan 1, 2002

By E J. Hofmann, J E. Hofmann, A J. Hofmann-Fritz

"With its Head Quarters in Perth, global heavy engineering company Hofmann Engineering is one of the largest family owned engineering companies in Australia. The company has pioneered a number of new manufacturing processes and design improvements for components of large comminution equipment.Some of these innovations are: Innovative design improvements of high pressure grinding roll (HPGR) forged steel tyres. Hofmann Engineering has developed unique patented tungsten carbide stud and edge protection designs which improve wear life and introduce quick and cost effective replacement options to further extend the life of the tyre. Development of forged fabricated mill heads using rolled and welded high tensile steel plate as an alternative to cast conical mill heads. Establishment of Australian capability to manufacture and export up to 42 ft. (12.8 m) diameter SAG mill shells. Techniques for fast track, product improved replacements of cracked or damaged mill gears, including in situ profile & wear measurements of girth gears using portable coordinate measuring machine (CMM) technology, forged rim steel and induction hardening technology. Gear and pinion mechanical drive designs to 24 MW or higher for SAG mills of 38 ft. to 42 ft. (11.6 m - 12.8 m) diameter as reliable alternatives to gearless drives.The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering on large, high powered equipment for both the domestic and export markets.CITATION:Hofmann, E J, Hofmann, J E and Hofmann-Fritz, A J, 2013. Australian innovations in high pressure grinding rolls and large grinding mill manufacture, in Proceedings MetPlant 2013, pp 141-151 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By D Gelling

Mineral sands dry plants consist of a large number of repetitive unit operations with significant transport delays, in the form of stream pipes, conveyors and elevators. As part of the P255 mineral sands sponsorship and using the JKMRC developed conductor/non-conductor (CNC) gauges, control loops have been implemented at the multi-duty dry plant of Cable Sands Limited at Bunbury. This paper describes the loops for kV control on a rougher high tension roll machines (HTR). The options available are product grade control and ratio control using the JKMRC CNC gauges, which measure the percent conductors in a stream. The purpose of control is to stabilise the circuit operation against disturbances such as atmospheric and feed disturbances.

Jan 1, 2001

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

By Laurance A. Beck

Safety is the most important aspect of haul road design. Although other aspects of road installation enter decisions on design, the safety of persons using the road has to be foremost for the duration of haul road usage. Other aspects of mad design focus on minimizing truck cycle time and fitting haul roads to the long-term configuration of the mine/quarry or construction project. Roads are often installed at high gradients for a short-term goal, but the long-term benefits are easily shown with lower gradient haul roads which provide better cycle times and lower operating costs.

Jan 1, 1995

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001