Search Documents

By A. M. Gaudin

Jan 1, 1962

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By Barnet Clemente, David Huaman

El sostenimiento de las labores en las operaciones mineras, son cada vez más consistente y seguros con la aplicación del concreto lanzado, en la unidad minera cerro lindo se ha migrado a este tipo de sostenimiento en un 100%. Todas nuestras labores están sostenidas con shotcrete, incluso el frente de la labor aplicamos el sostenimiento con shotcrete, que llamamos malla de sacrificio, sin embargo este tipo de sostenimiento es costoso, pero te da muchas facilidades para mejorar los rendimientos y se hace más segura la mina, para lo cual contamos con una planta de concreto exclusivamente para este servicio, con una capacidad de 30 m3 por hora, lo que necesita la mina es 7000 m3 mensuales para cubrir todas la labores de producción, preparación y desarrollo, incluso hemos considerado la labores de rehabilitación y resanes por la misma operación minera, esta operación nos da una demanda de 9 mixcrets en operación y un stand by, con 4 alphas operativos y 1 en stand by.

Sep 1, 2017

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By Edwards A. B

A table concentrate obtained experimentally by the New Occidental Gold Mines N.L. has unusual interest on account of the presence in it of abundant coated or "black" gold. The concentrate was obtained from ore from the New Cobar mine, Cobar, New South Wales, by feeding the oversize product from a "Dorr Bowl classifier to a Card table.Its assay value was 129 oz. of gold and 52 oz. of silver per ton, yet practically no free gold could be seen on panning.When, however, the concentrate was digested in hydrochloric acid fine rusty gold could be obtained by panning.The following chemical analysis was carried out by the mining company on a similar sample of concentrate.

Jan 1, 1941

The Electrolytic Refining and Smelting Company of Australia Limited (ER&S) operates a copper smelting and refining plant and is situated close to the heart of the highly industrialised area of Port Kembla. In March, 1982 the Company entered into an undertaking with the State Pollution Control Commission (SPCC) to monitor ambient levels of sulphur dioxide (S02) gases present in the atmosphere in the surrounding urban area. Despite the use of a 200 metre high stack for dispersal of the smelter waste gas stream at ER&S, two local suburbs, Warrawong and Primbee were experiencing on occasions high ambient concentrations of S02 resulting in discomfort to local residents. In late March 1982, ER&S installed a highly advanced S02 monitoring system to continuously monitor the levels at Warrawong. The system was extended to include S02 monitoring at Primbee in November 1982, and further extended in June 1983, to include an input of meteorological data. Initially the system was designed to monitor and react to high concentrations of S02 at either of the two monitoring stations. Currently however, refinement is taking place to allow a predictive nature to be built into the system such that it not only reacts to an adverse situation but can predict weather patterns likely to cause high concentrations and thus avoid these events. The entire system is still undergoing a growth and development period, however the results obtained to date are pleasing to both the Company and the SPCC.

Jan 1, 1984

Mount Isa Mines Limited first installed electronic data processing equipment in 1959. The decision to replace this equipment with a computer was motivated by the need for greater processing power and the availability of new and less expensive computers. Consideration of hardware software and delivery features of available equipment, resulted in the selectIon of an ICT 1900 series computer which was installed in March 1966. Special air-conditioning and power stabilization equipment was also required.Systems design and programming was carried out by personnel recruited from within the Company and trained by the computer manufacturer. Early work was hindered by the problems of remote location.Initial applications were basically accounting functions whIch were taken over from the EDP installation. Subsequently computer applIcatIOns of a more complex technical nature have been undertaken. Future work will include both "scientific" and data processing applications.

Jan 1, 1968

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

Formation of either sodium jarosite or lead jarosite from concentrated chloride solutions containing small concentrations of sulphate has been demonstrated. Sodium jarosite is precipitated at 95-100°C from FeC13-FeCI2-NaCI-PbCI2 solutions to which was added Na2SO4 or Li2SO4 in amounts greater than 0.05 M. In the absence of alkali metal ions capable of forming jarosites, lead jarosite was precipitated from either FeCI3-PbCI2 or FeCI3-FeCI2-LiCI-PbCI2 solutions to which had been added small amounts of sulphate. Many of the factors affecting jarosite precipitation from chloride solution have been elucidated, and the most critical were sulphate concentration and initial pH. Concentrations of HCI in excess of O. I M essentially suppressed the production of jarosite in chloride media. Alkali jarosite, precipitated in the presence of dissolved lead, incorporates a small amount of this metal into the alkali jarosite lattice. Small but significant amounts of copper can also be incorporated into alkali jarosite and the amount is further increased in the presence of lead. Other divalent base metals such as Zn, Cd or Ni are not significantly precipitated. Sulphate control in either FeCI3 or FeCl3-NaCI leaching systems could likely be maintained by jarosite precipitation provided that the acid concentration of the solution was low.

Jan 1, 1981

By Robert J. Kuhne

The Iron Ore Company of Canada has successfully employed advanced process control (APC) to optimize the operation of their induration machines. A significant increase in machine throughput and a reduction in fired pellet quality giveaway were observed following the APC implementation on all six machines. This paper discusses the opportunity for process control optimization in induration, reviews the property estimation and multivariable control technologies, and describes how the IOCC control strategy captured this opportunity. APC performance data is presented. The dependence of APC performance on control room operator acceptance, process equipment and instrumentation is highlighted.

May 1, 2007

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By Steven D. Botts

The paper point out the Antamina's social policies with Huascarán National Park. The project had required the mine engage with the communities most affected by the mine development, its operation, and closure. In this sense, operating within this social context has required Antamina to first be effective in understanding who the affected people are –at the local, regional, national and international levels. This understanding is also a process that requires time. Through the HWG, the company has achieved engagement, as well as an understanding an appreciation of viewpoints and perspective that has resulted in the protection of HNP, as well as the timely development of the project, with support of stakeholders. Therefore, the experience of the HWG was become for other natural resource projects in complex settings, involving national and international stakeholders and protected or sensitive areas.

Sep 13, 2001

By A. J. Terrones

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,' by Barrell on Marysville, Mont.,' and by Gold-schmitt on the Oslo district, Norway,' laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf' made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control" in ore finding. Some years later Harrison Schmitt" fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed. Primary exploration and careful sampling of recognized structural targets were instrumental in outlining the copper ore potential at the Antamina and Tintaya districts, thus proving the benefits and reward of careful geological examinations in this type of deposit. The Magistral District: This district lies in the Province of Pallasca, Department of Ancash, in northern Peru, at 8o 16' S and 77" 47' W. High to medium grade copper orebodies in garnetite, bordering a quartz monzonite stock, are exposed at the bottom of a glaciated valley in the western slope of the Andes at 4250 m (14,000 ft)* elevation.

Jan 1, 1959

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

In some parts of the world explosions in mines are more commonplace events. Even in the more developed nations explosions have occurred in recent times. In some cases these mines have significantly lowered their lost time injury frequency rates and as such considered themselves to be ?safe? operations. The consequence of these explosions has been devastating. It is not just the loss of those underground, but also to the families that have lost people in them and the broader community that has lost friends, income, business opportunities, and in many cases support and sponsorships. It begs so many questions, ?What went wrong??; ?Why were the circumstances not foreseen??; ?What could have been done to prevent it??; ?How is it that no one stopped it, reported it, fixed it etc.??. Being held accountable for negligence, should not be overlooked, however this may not aid the processes required to find all the answers. If the nature of explosions is understood, the circumstances and tools to prevent them are readily available then the occurrence and reoccurrence are due to weaknesses or inadequacies of the systems of work or in the implementation of them. This paper restates the fundamentals of gas explosions, examines the options to control the underground environment through ventilation, gas management and monitoring, education and training. Case studies have been used to examine systematic failures in ventilation management. In some of these cases it is not so much, the system that had been developed, but the interpretation and implementation of the system that resulted in the failure and subsequent loss.

Aug 1, 2013

By Rolf B. Pedersen, Ana Filipa Marques, Ingunn H. Thorseth, Ingeborg Okland

"Deep sea mining of polymetallic sulphides will change the physical and chemical conditions at the seafloor by creating scars when sulphides are removed, and potentially also by deposition of mine tailings at the seafloor. These changes will impact the existing ecosystems at the seafloor in and around the mined areas. Seafloor Massive Sulphide deposits that have been exposed to oxic seawater weather into Fe-metal-oxyhydroxides. However, the rates of weathering and release of heavy metals and other toxic compounds to the environment from freshly exposed sulphides in a deep-sea environment are not well studied.During a cruise to the Arctic Mid-Ocean Ridge in the Norwegian-Greenland Sea in July 2014 we will initiate in-situ experiments investigating the microbiological and geochemical processes involved in the weathering of freshly exposed massive sulphides deposits in a natural environment. This will be done by creating scars in naturally occurring sulphide deposits and by deploying weathering experiments at the seafloor. The sites will be revisited and re-sampled in 2015. The mobility and fate of heavy metals will be one of the main concerns of the study as well as constraining the time it will take for exposed sulphides to return to the chemical state present prior to mining. In this presentation we will present the experimental framework and the preliminary results from the July 2014 cruise. This project is part of the EU funded MIDAS (Managing impacts of deep sea resource exploitation) project."

Sep 1, 2014

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

Modelling Channel Scale Flow in Heap Leaching Using Smooth Particle Hydrodynamics (SPH)

Sep 13, 2010