Search Documents

CONTENTS.IntroductionAcknowledgementsDescription of MineVentilation of MineOrganisation of Fire Fighting SquadsTraining of Fire Fighting SquadsRescue WorkFire Fighting and Rescue EquipmentFire AlarmsConclusionINTRODUCTION.This paper should be read in conjunction with that by R. P. Hooper, entitled "Underground Mine Fire Prevention at the South Mine," Broken Hill. Contents of the paper have been arranged similarly for easy reference. The methods used in educating employees in the use of Proto apparatus remain basically the same, but many changes in the methods and equipment used in subjugating fires have been brought about by the practical experiences gained by officers of the company in extinguishing the outbreaks which occurred in the latter half of 1944.Three fires took place during this period, the first in July, on M.L. 11 in openings leading to timbered workings previously worked and subsequently abandoned by...

Jan 1, 1946

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By Xu Z, Hu C

An attempt has been made to investigate the performance of green pellet formation of the Daye magnetite concentrate from the weak-magnetic separation plant. The optimum conditions for the commercial production of green pellets was found through experimental research. The satisfactory size range for balling is 75 ¦ 3 per cent -200 mesh. The suitable moisture content is between 8.7 and 9.1 per cent and the optimum amount of bentonite added is between 1.5 and 2.5 per cent. The emphasis is on the size of the feed materials since the grinding fineness, which can be obtained at the plant, at most is 78 per cent -200 mesh. If the optimum fineness for the pellet formation is above this value, this means that the concentrate must be re-ground before balling. The results from experiments showed that a good quality green pellet can be attained by using materials below 78 per cent -200 mesh, which provides a strong foundation for the commercial production of green pellets.

Jan 1, 1999

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

CENTRAL mine ore consists mainly of galena and marmatite in a siliceous and rhodonitic gangue, the average assay values being approximately 11.5 oz. per ton Ag, 14.5% Pb, 14.5% Zn, 1.3% Ox Pb, 0.3% Ox Zn.Owing to the 1923 fire in the underground workings, much of the ore now being mined has been subjected to a certain amount of oxidation, as shown by the oxidised values above.This factor is of great importance from a flotation point of view, as a sulphide surface which has been subjected to the influence of oxidation is not as amenable to flotation concentration as a fresh sulphide surface. The importance of this factor is increased when a differential flotation is to be made, and, as in the case of Central mine ore, the sulphide, which is to be floated first, has been oxidised...

Jan 1, 1931

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By Greenwood J. N

This work was commenced at a time when information on the manufacture of cemented tungsten carbide was urgently needed in Australia. Much information of a general type has been published, but many of the details of the processes used are still undisclosed. The aim of this research was to determine a satisfactory way in which cemented tungsten carbide could, be made, and to investigate the problems which are associated with the process. As the work proceeded, its ramifications grew continually, and it was necessary to limit the possible lines of investigation. After much experimental work, a 9% cobalt-tungsten carbide alloy was developed which had satisfactory properties when used as a cutting tip. The effect of certain variables on the properties of this particular alloy was investigated.The tungsten carbide was prepared in stages from King Island scheelite concentrates under strict laboratory control, whilst the cobalt (1) used was made from cobalt oxide prepared from crude cobalt oxide obtained from Eisdon.In order to clarify the detailed experimental work, a brief summary of the method used for the preparation of cemented tungsten carbide follows.Tungsten carbide and cobalt are prepared in a very finely powdered state, and are then thor,oughly mixed by a ball milling operation. The resultant mixture is pressed in a suitably shaped die into small compacts which are subsequently '''presintered,'' i.e., heated' in hydrogen between 800°C. and 1000°C. The final sintering is carried out in hydrogen between 1,400°C.and 1,600°C. for about half an hour. These "alloys" may contain from 3 to 13% cobalt, depending on the particular properties required of them.PREPARATION OF MATERIALSThe tungsten oxide prepared as described by Smithells (2) was extremely finely divided, and after a few hours' grinding in a ball mill, the powder consisted of material below 10 microns iJ;l size. The oxide was reduced to tungsten metal with hydrogen in a tube furnace. The reduction was carried out at 800-900° C., a rapid flow of hydrogen being maintained in order to remove the water vapour' formed as a result of the reactions:

Jan 1, 1942

By Tomás Gonzáles

El presente trabajo describe la metodología usada para evaluar las estrategias de las alternativas del planeamiento a largo plazo en la explotación del mineral y el lixiviable en la Mina Toquepala.

Aug 25, 2002

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By Johnson T, Huynh D

The State Electricity Commission of Victoria is conducting a program of research and development into alternatives to the use of conventional boilers for the generation of electricity from brown coal. The objectives of the program are to reduce the cost of electricity generation and also to improve the thermal efficiency so as to reduce the emission of greenhouse gases and other pollutants. The program presently includes the following four technologies: Hydro-thermal Drying, Direct Coal Fired Gas Turbine, Integrated Gasification Combined Cycle, and Steam Fluidised Bed Drying. The Hydro-thermal Drying process produces a combustible coal-water-slurry fuel which is suitable for use in a coal fired gas turbine. The coal fired gas turbine has the potential to produce electricity at a lower cost than conventional power stations and when combined with a steam cycle, it will also use significantly less coal. The Integrated Gasification Combined Cycle process gasifies the coal, cleans the gas, and then bums it in a gas turbine/combined cycle. This process is being developed in Europe and the USA in order to meet their stringent emission regulations. It offers Victoria cleaner more efficient and cheaper electricity.

Jan 1, 1992

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

Mr. Chairman, distinguished guests, ladies and gentlemen. Thank you for asking me to your conference, with its most fundamental and appropriate topic of &apos;Investment in Mining&apos;. I must confess at the outset that I am one of those Australians who has rarely visited your fair land of New Zealand. This is in fact only my third visit, with all three related to Institute Conferences, and all much too brief. In so many ways your country provides a counterpoise to ours, despite the obvious disparities in size and population. And I am not only referring to the Bledisloe Cup! We would certainly each be much more lonely without the other, in this strange long-lost corner of the globe û if globes can have corners. Such an important factor in common in our shared heritages has been the mineral industry we have won from our alluvials and our rocks&nbsp;û especially for gold. So much of the major mineral developments which have supplied the world&apos;s appetite for metals and fuels in the past two hundred years has come from the countries settled in that period by people from Europe, especially those from the British Isles. So much of the technology for mineral and metal extraction has come from the skills of those people in New Zealand and Australia. And so much of the further development of metal processing and manufacturing of productive equipment has come from those people and from their cousins throughout the world. It is, I believe, a fair question to ask why we have failed to build on those early and considerable successes, and why we have in so many ways apparently been so content to allow others to add value to our raw materials, and to take our technological developments on to levels far beyond those that our domestic markets could sustain.

Jan 1, 1988

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

By Mark Kennedy

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation?s cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2013

By Richard P. Reiff

"The Facility for Accelerated Service Testing (FAST) program has been involved in numerous rail wear tests since its inception in 1976. A number of specialized tools have been developed to aid in assessing specific performance parameters including gauge face wear, head height loss, metal flow, head area loss, hardness, and welded rail end batter. The layout of a test site, including position in curve, number of measurements per rail, and train operation must be properly controlled/monitored to provide valid wear comparisons.This paper will provide an overview of the above-mentioned tools and techniques. In addition, a summary of recent test results from FAST, including information on head hardened rail investigations, will be provided. A set of guidelines for establishing a revenue service field test site will also be provided to aid users in performing evaluations of their own.IntroductionBackground of Rail Wear Testing at FASTThe Facility for Accelerated Service Testing (FAST) located at the Transportation Test Center, (TIC), Pueblo, Colorado has been involved with testing of rail since program initiation in 1976. A huge data base of rail wear information has been gathered from FAST operations under a variety of rail metallurgies, lubrication conditions, and measurement techniques. Attempts at obtaining meaningful rail wear information from early (1976-1978) FAST rail wear data was hampered by two main factors: (I) measurement techniques were insufficiently accurate for the amounts of wear being experienced, and (2) the lubrication was not sufficiently controlled to obtain uniform conditions for a sufficient measurement time period.Subsequent test periods were operated with improved measurement techniques and controls that ensured statistically valid data. The policies and conditions that permit accurate rail wear assessment will be reviewed and outlined in this paper, along with some specific TIC and field examples that will allow the user to improve the accuracy of a field rail test on their own operating property."

Jan 1, 1988

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920&apos;s underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor&apos;s Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By Anil K. Beersing

Effective drainage systems are required for reclamation of mine-disturbed areas to control surface water runoff and avoid excessive erosion. For the conventional structural design approach, armouring material necessary to satisfy the design criteria should not move during the design flood event since displacement would uncover the erodible underlying materials. This paper discusses an alternative geomorphic approach for designing drainage channels and watershed landscape. The approach is based on quantitative studies of geomorphic processes operating in a watershed. A design based on the geomorphic approach replicates the configuration, channel regime, sediment volume and hydrology of natural and mature drainage systems. Movement of some armouring material is acceptable in such an approach because the channels are allowed to mature by natural degradation and aggradation, with erosion rates comparable to the natural environment. The key advantages of a geomorphic approach over a purely structural approach include reduced sizes of armouring material, geomorphologically sustainable landscapes, ?walk-away? or maintenance-free design and reduced liability in the future. The geomorphic approach is illustrated using the example of a coal mining operation in northwest U.S.A. The paper discusses field data collection, design criteria, typical design details, and construction methods.

Apr 1, 2005