Search Documents

By Daniel Eduardo Parodi

Para acompañar el plan de aumento de producción de slabs de Siderar, fue necesario proyectar una nueva unidad separadora de aire para incrementar la generación de oxígeno, nitrógeno y argón. La premisa que direccionó este proyecto fue la integración y sinergia de la nueva unidad con el sistema de la Central Termoeléctrica y Altos Hornos, con el objetivo de salvar condicionamientos, obtener beneficios energéticos y aumentar la confiabilidad operativa. Como resultados de esta línea de trabajo se espera: Optimizar el aprovechamiento de gases de proceso, mejorando así el balance energético y la ecuación económica en la producción de los gases industriales; Mejorar el aspecto ambiental disminuyendo el quemado de gases en antorcha, reduciendo el consumo de combustibles fósiles y la compra de energía eléctrica; y aumentar la confiabilidad en el suministro de gases y del sistema de aire soplado a Altos Hornos.

Sep 25, 2017

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By J. Patrick Ryan, Thor H. Kiilsgaard, Charles W. Merrill, E. T. McKnight

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reduc ing demand. This paper examines poss ible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Feb 1, 1965

By James Pirie

"The major Archean gold deposits in the Red Lake greenstone belt, which have produced over 374 million grams of gold since 1930, occur near the top of the lower komatiitic to tholeiitic mafic to ultramafic metavolcanic sequence. The upper calc-alkalic mafic to felsic rocks form three discrete and separate ediftces overlymg this lower sequence.The gold deposits are classified according to their stratigraphic or lithologic associations into:1) mafic-volcanic-hosted deposits;2) felsic-intrusive-hosted deposits; and3) stratabound deposits.Group 1 and to a lesser extent Group 2 deposits occur within zones of alteration several square kilometres in extent. The nature of this pervasive alteration can be characterized by comparison of petrochemical data from the altered rocks and their fresher equivalents some distance away. The altered rocks have substantial addition of SiO2> CO2, K2O, As and Sb and subtraction of Na20, CaO, MgO and total Fe. Cr, Ni, Co and Zr appear to have been relatively immobile. Hydrothermal alteration and gold deposition probably accompanied early fumarolic activity and continued during subsequent deformation the metavolcanic sequence, with gold eventually being mobtltzed and concentrated into major vein structures to form the present orebodies. The smaller Group 2 deposits formed by emplacement of felsic intrusions into already altered, anomalously gold-bearing mafic metavolcanics, with the heat from the intrusions setting up parasitic hydrothermal systems which mobilized the gold and deposited it along with minor sulphides in fractures in the cooling intrusions."

Jan 1, 1982

By Henry Kreisinger, F. K. Ovrrz, C. E. Augustine

The Bureau of Mines is conducting investigations to determine how fuels belonging to or for the use of the United States Govern- ment can be utilized with greater efficiency. As a result of these investigations a number of reports have been published, each report treating of one phase of fuel utilization. A list of these publications is given at the end of this bulletin. The efficient utilization of coal depends on the correct design of furnaces and on their proper operation. To attain both of these conditions a knowledge of the fundamental principles of combus- tion is necessary. Therefore, the study of the combustion of coal in industrial furnaces has been made a part of the bureau's fuel in- vestigations. The desirability of investigating the fundamental principles of combustion was suggested by the study of a large number of steam- ing tests made by the fuel-testing division on coals from all of the more important fields in the United States. The results of these tests have been published in Bulletin 325 of the United States Geological Survey and in Bulletin 23 of the Bureau of Mines. As a result of that study a plan to investigate the combustion of coal in a special apparatus in which all conditions could be controlled was presented to the National Advisory Board for Fuels and Struc- tural Materials at its meeting of April 10 and 11, 1906. The plan received the approval of the board, and since the establishment of the experiment station of the Bureau of Mines at Pittsburgh the investigation of the combustion of coal has been carried on intermit- tently. The history of these investigations is given in Technical Paper 63.

Jan 1, 1917

By Hal J. Kelly

A number of problems that developed in processing the halloysitic clays of eastern Washington and northern Idaho were investigated by the Bureau of Mines. The deflocculating effect of tetra sodium pyrophosphate is compared with several other compounds, and on the basis of current theory, the advantage of sodium pyrophosphate as a deflocculating agent is explained. The adsorption of the sodium ion by clay in a clay"-water system was established by a radioactive tracer technique, and the deflocculating action of sodium pyro- phosphate was postulated. The effective dispersion of the halloysitic clays was limited by the occurrence of tightly bound aggregates of small, individual crystals. Disaggregation of the agglomerates was investigated by liquid extrusion and ball milling of dilute slurries and by extrusion of the clay in a plastic state. The greatest increase in the production of small particles was by high? pressure liquid extrusion.

Jan 1, 1963

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By Antonio Fernández, Javier Cáceres, Enrique Ramírez, Camila Yepez

El sector minero es una de las pocas industrias que depende de los precios de mercado para producir. Por lo cual, mantener ventaja competitiva y garantizar la eficacia del proceso para alcanzar las metas propuestas por la empresa minera representan un desafío constante. Esta investigación tecnológica tiene como objetivo maximizar la eficacia en los procesos de transporte y perforación manteniendo los costos más bajos en su proceso productivo. La investigación presentó dos desafíos durante la etapa de prueba que fueron la especialización del personal y modificación progresiva de los equipos para cada actividad específica.

Sep 30, 2022

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Dan Preston, Shane Yanagisawa, Robert Marshall, Don Deere

Geotechnical Baseline Reports often estimate the number of cobbles that will be encountered in terms of volume or weight. These estimates are practically impossible to verify in the field. ClaroVia Holdings in conjunction with Frontier Kemper Constructors Inc. developed Digital Geologist 2.0 to classify and count cobbles discharged from an EPB TBM at the RSC7 project in Burbank, CA. The system worked by using two stereoscopic laser sensors with a global shutter to scan and count cobbles at 12 frames per second. Results of the effort are revealed along with lessons learned and paths for improvement.

Jun 13, 2023

By Mario Alejandro Bendezú

En el presente artículo se analizan los factores esenciales para desarrollar un proyecto minero de uranio y litio en Perú. Luego de describir los requerimientos y perfil que debe tener la empresa minera a cargo —en este caso, una minera junior—, se revisan las implicancias operacionales, legales, económicas, sociales y ambientales del hecho de que los yacimientos contengan minerales radioactivos.

Nov 30, 2018

By M. D. Cooper

IN spite of the uncertainty in the bituminous coal industry during 1933, progress worth recording has been made. Along with other industries, coal has felt the effects of business stagnation, but even in the worst weeks of the past four years, .the total production of bituminous coal in the United States was seldom less than half the production in some of the best weeks of the more prosperous years, a record better than that of many industries. However, the competition of other fuels and sources of power, together with the increased efficiency in the use of coal, has brought anxiety to producers. This has resulted in pressure for reduction of costs, not always by the wisest means. On the other hand, the effort to survive has directed increasing interest toward research, a wholesome development in a difficult situation. Wages, limitation of hours of labor, and the NRA have occupied much time and thought. Following a period .of wage cutting paralleling price cutting, the industry found itself rather suddenly faced by the President's Agreement, followed in due course by the Code, and then in many places by the agreement with the United Mine Workers. Although there is still some uncertainty in regard to the detailed working out of the new arrangements, there seems to be an honest endeavor by the signatories to the Code and Agreement to work them out in a straightforward manner.

Jan 1, 1934

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

By Henry Kreisinger

Some of the investigations conducted by the Bureau of Mines have for their object the collecting and disseminating of information regarding methods by which the fuels of the country may be most efficiently used. As the analysis of flue gases tends to develop better methods of firing, which in turn reduces waste of fuel, the Bureau of Mines in this bulletin presents for the benefit of those in charge of boiler plants and all other persons interested detailed information on methods of sampling and analyzing flue gases, and on the utilization of the analyses in promoting boiler-room economy. This bulletin is intended to be a companion to Technical Paper 80,a and is written in plain and nontechnical language, as far as possible, so that it may be readily understood by persons who have not had the advantage of a technical education. Whenever possible, illustrations of apparatus and methods of handling have been used rather than elaborate descriptions.

Jan 1, 1915

By Jorge Olivari Ortega

La magnetita como mineral perteneciente a la familia de las espinelas, se utilizó principalmente en los rituales de entierros pre-hispánicos. Sin embargo, este puede concentrarse en lechos importantes en razón de su cristalización tardía en el flujo magmático y de su peso específico elevada. Por ello, el presente texto describe el uso de este mineral como parte de las piezas encontradas en Marcacocha, así como amuleto y herramienta (honda) en la cacería de animales auquénidos. Asimismo, refiere su empleo en el cuidado del pastoreo de los animales - en tanto pieza redonda de protección contra el robo de ganado.

Apr 1, 2017

By J. W. Allen

This report reviews the work performed on Task M of Bu-Mines Contract H0220073 to develop an engineering model of a surface and subsurface communications system for normal mine operations and for post disaster rescue operations. The system concept provides for one-way transmission of digital information between a number of identifiable subsurface terminals or subcenters and a single surface station. It also provides 2-way voice communications between the subcenters and the surface station. The basic communications link is electromagnetic signaling through-the-earth, but the system is also capable of using mine phone lines as an alternate link. Engineering models of three subcenters and one surface terminal (see Figure 1-1) have been fabricated in order to demonstrate the system's performance. The system concept, however, permits up to 20 subcenters to be incorporated if desired. Additional subcenters are also feasible for large mines if they can be deployed in the mine to operate on a noninterfering basis.

Jan 1, 1973

By L Torckler, R L. Brathwaite

At Neavesville gold-silver (electrum) mineralisation occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydrothermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz-adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy and sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt per cent NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei and Broadlands. The age of the rhyolitic pyroclastics and related alteration and mineralisation is probably Pliocene and Neavesville therefore represents a fossil geothermal system. The intensely fractured zones containing the gold-silver mineralisation were probably produced by hydraulic fracturing generated by accumulation under pressure of hydrothermal fluid in blind fault zones. Study of fluid inclusions indicates that hydrothermal quartz associated with electrum was deposited under boiling conditions. High grade electrum mineralisation at Graces workings appears to be localised by reaction of hydrothermal fluid with sedimentary marcasite in black shale.

Jan 1, 1980

By H. A. Doerner

"The following report is submitted, in compliance with the request made by the Honorable W. H. Sproule, Chairman of the Committee on Mines and Mining, to the Director of the United States Bureau of Mines, that the bureau investigate the most modern processes for the production of radium from its ores. A thorough search of technical publications and patent office files was made. Outstanding authorities on the subject as well as persons claiming novel or secret methods were interviewed.Unlike most other elements, it is not possible for radium to occur naturally in a pure or concentrated form. This is because radium is one of a series of unstable elements which, by a constant, spontaneous, atomic disintegration, change from one element to the next in the series. Uranium is the ""grandparent"" of radium. The rates at which radium atoms are ""born"" and ""die"" are so related that only one part of radium can exist in equilibrium with three million parts of uranium. Consequently radium is only found associated with uranium minerals, and the ratio of radium to uranium is never more than one to three million. Since uranium is a rather rare element, the scarcity of radium is almost beyond comprehension. Nevertheless minute traces of radium can be detected in nearly all rocks.The carnotite ores of Colorado and Utah were the chief source of radium for many years.In the fall of 1922 news of the very rich deposits of radium ore discovered in the Belgian Congo caused most complete cessation of domestic production. The Congo ore contains pitchblende and a number of alteration products, including the new minerals bequerelite, curite, krasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent uranium oxide has been produced. It seemed certain that radium could be extracted from the Conga ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgian syndicate to market the foreign product in this country. The retail price of radium has been held at $70 per milligram, but large orders are filled as low as $50. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price with one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, finally shut down its plant."

Dec 1, 1930