Search Documents

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Sutham Niyomwas

Keywords: Al2O3-SiCW, Ceramic Matrix Composite, Carbothermal Reduction, Kaolin The formations of Al2O3-SiCw composite have been obtained in situ by carbothermal reduction of a mixture of kaolin and activated carbon. The reaction temperature was controlled at between 1400°C to 1600°C. The synthesized products were mixtures of alumina and silicon carbide in the form of whiskers. The effects of milling time of precursors and reaction temperature are presented. XRD and SEM analyses indicate complete reaction of precursors to yield Al2O3-SiC as product powders, with the SiC having porous and whisker morphology.

Jan 1, 2005

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By R. Fragoudakis

AISI 4130 steel is a medium carbon Cr-Mo steel used in automotive, aeronautic and other general-purpose industries. In this study, 4130 steel fatigue specimens were carburized at 927oC to enhance the carbon content in the steel, raising it from approximately 0.30% (non-carburized) to 0.90% (carburized, oil quenched and tempered). Rotating bending fatigue tests were performed on the R. R. Moore Rotating Beam Fatigue Testing System, in order to determine the high cycle fatigue (HCF) life of 4130 steel and plot the corresponding S-N diagrams. A comparison of the results of carburized and non-carburized specimens shows that carburizing of steel: a) increases the surface hardness and b) improves the fatigue strength of the steel by at least two orders of magnitude.

Jan 1, 2010

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By M. S. Borges

The need for the waste management industry to reach environmental patterns, technological innovation, and a technological demand of the productive sector is covered by this study. The environmental care and responsibility in the industrial sector and the necessary cultural changes for companies and entities is also emphasized. A collaborative tool was developed to help all partners involved in the environmental administration. This tool focuses on the interaction among residue generators in the productive chain. It was developed for a vehicle assembler company supported by entities or institutions with emphasis in the research, development and innovation, with expertise and capacity for new products creation, as well as reuse, recycling and reduction of by-products generation. The work aims to establish a tool for socio-environmental management, focusing on promotion and interaction between industrial waste generators sectors.

Jan 1, 2010

By Theo Lehner

"The Boliden Rönnskär Smelter operates in the European Context of tight EH&S limits, with ever increasing regulations and tribulations. The near future promises to bring new burdens in the form of C02 trading, miners and pre-treaters increased appetite for a larger share of contained values, and changing compositions and competition in raw materials. On the other hand, European Smelters such as Rönnskär, Harjavalta have demonstrated an astonishing power of survival. This presentation lists and comments on current challenges but opportunities for increased survival power are also presented. One example of the latter is the ongoing investment into increased treatment capacity for e-scrap.UPDATE ON RÖNNSKÄR OPERATIONSThe Rönnskär Smelter has achieved 80 years of age with no signs of retirement. The smelter is most active in spite of its age! And it has undergone some face lift operations to maintain its attractiveness.Raw material, processing facilities and a market for the products are some essential prerequisites for a viable operation. To justify long term survival, economic terms such as return on investments and positive cash flow need to be considered. Below, we illustrate how the Rönnskär Smelter complies with these terms. To update the reader on current operations, our current flow sheet is depicted in Figure 1. The figure summarizes our current input and output."

Jan 1, 2012

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

This paper outlines the complete failure of the U.S. in status and relevance in Rare Earth Oxides (REO). Although rare earth oxides are strategic and critical in their own right, refining these REOs into elements and alloys is even more important for the development of "Green Technologies" and advanced weapons systems. America does not have an active domestic source of rare earth oxides. America does not have any heavy rare earth elemental or alloy capabilities. The magnitude of this failure continues to become more apparent as the manufacture of REO based electronics and magnetic components moves eastward towards China. China has succeeded in outmaneuvering the United States and the world in its quest to control the rare earth oxides, elements and alloys, and the many industries dependent upon REO. What can be done?

Jan 1, 2010

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010