Search Documents

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By Russell C. Frith

This paper examines the design of longwall shields, focusing on those aspects that are critical to either their successful application or contribution to failure during longwall extraction. In many instances, longwall shields are assessed and designed along lines similar to that of roadway ground support systems, namely according to typical or normal geotechnical conditions. However it will be contended that for longwall shields, this is inappropriate because unlike roadway ground support systems, longwall shields cannot be supplemented with additional or secondary support in localised areas of adverse geotechnical conditions. In other words, the longwall shield needs to be designed according to what are judged to be worst case or adverse geotechnical conditions?the outcome being that a well-designed shield will be significantly over-rated for the majority of its working life. Therefore, it will be argued that the additional capital cost of such shield design can be readily justified as a prudent riskbased outcome that is essential to minimising future business risks due to strata instability on the longwall face. Shield geometry will be discussed, including such relevant factors as leg angle, inclination of the top caving shield, canopy ratio, operating height range, and tip to face distance. These are all well-established longwall shield design considerations and, most importantly, areas whereby inadequate design can render a longwall shield as highly ineffective. The issue of tip to face distance will be considered in detail, in particular, the extent by which it is an important geotechnical design consideration, the conclusion being reached that, in fact, it is not. The critical importance of maximising set to yield ratio within practical operating limits will be justified, the wisdom of this having been subject to questioning in more recent technical literature. Overall, the aim is to provide the industry with a set of suggested guidelines for future use when designing longwall shields and, hopefully, to initiate discussion on a subject that, unlike roadway ground support design, is not well covered in its entirety in the published technical literature.

Jan 1, 2013

By Zhengdong Liu, Kaizhong Zhang, Zhaonan Jiang, Yuanping Cheng, Biao Hu, Qingquan Liu, Ranpeng Wang

"Major coal mining areas in eastern China have entered into the deep mining state. Gas pre-drainage, which has been successful at shallower depths, is not suitable at greater depths because of complex conditions. Coal permeability, which is closely related to the damage behavior of coal, is the most important parameter in determining gas migration and gas drainage in a coal seam. To achieve an optimal gas drainage design in a deep mining state, the damage and permeability evolutions of coal should be further studied. The progressive failure process of coal has been analyzed by conducting a series of triaxial loading and unloading tests. The development of coal fractures has been successfully quantified, and the corresponding characteristic stress points have been obtained by using Martin’s fracture model and the stress-strain curve. Coal will produce plastic deformation, and its permeability will rapidly increase when the stress level reaches damage expansion stress. INTRODUCTION Coal mine methane (CMM) is a general term for all methane released during and after mining operations. CMM is both a potentially valuable energy and a serious hazard in active coal mines. Degassing coal seams is important for mitigating this hazard and results in the beneficial recovery of a cleanburning, low-carbon fuel resource (Karacan, Ruiz, Cotè, and Phipps, 2011). The permeability of coal is a key parameter in determining CMM production, coalbed methane (CBM) production, CO2-enhanced coalbed methane (CO2-ECBM) production, and CO2 storage in coal seam reservoirs (Connell, Lu, and Pan, 2010; Chen et al., 2011; Perera, Ranjith, and Choi, 2013). Significant research has been condcuted to the study of the evolution of coal permeability. These studies revealed that coal permeability evolution is controlled by the competing influences of effective stress and sorption-induced coal deformation. Chen et al. (2011) investigated the influence of an effective stress coefficient and sorption-induced strain on the evolution of coal permeability. Robertson and his team (Robertson, 2005; Robertson and Christiansen, 2005) measured sorption-induced matrix strain and permeability changes with regard to CO2, CH4, and N2. They found that the compressibility is not constant in a natural coal sample. Karacan (2007) conducted a series of experimental tests to study the swelling-induced volumetric strains internal to a stressed coal associated with CO2 sorption. Liu et al. (2016) investigated the effects of matrix swelling area propagation on the permeability evolution by using both natural and reconstituted samples. Many coal permeability models have been developed to describe the permeability evolution under uniaxial loading, biaxial strain, hydrostatic confining pressure, triaxial strain, and triaxial stress. Recently, some analytical permeability models have been developed to describe the anisotropic permeability behavior (Palmer, 2009; Pan and Connell, 2011; Robertson and Christiansen, 2005; Wang, Zang, Wang, and Zhou, 2014; Chen, Pan, Liu, and Connell, 2012)."

Jan 1, 2017

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By L. A. Sandbak, Yan Xing

"The purpose of this study is to evaluate the rock mass stability around the tunnels by three-dimensional (3-D) numerical modeling. Complex geological and tunnel features have been included in the model using the software package 3DEC™. Based on the available information on stratigraphy, geological structures, and mechanical properties of rock masses and discontinuities from the underground mine, 3-D stress analyses were performed on various cases with different K0 (lateral stress ratio) values, constitutive models, as well as support systems. Relations between these factors and the distributions of stress, displacement, and failure zones around the tunnels were obtained and discussed. Finally, comparisons between the field deformation measurements and numerical simulations are used as validations for the simulations, helping to determine the appropriate K0 value and material constitutive models for the underground mine.INTRODUCTIONThe case study site is an underground mine in the USA with a monthly ore production between 20,000 and 30,000 tons. The regional geology of the mine is structurally and stratigraphically complex. Rocks in the area include carbonaceous mudstone and limestone, tuffaceous mudstone and limestone, polylithic megaclastic debris flows, fine-grained debris flows and basalts, all part of the Cambrian-Ordovician Comus formation and related dikes. Both the mineralization and faults have general orientations striking N-S to NW-SE with high dip angles. The ore body in the mine has an incline of about 25---45 degrees located in relatively low quality rock; hence, cut-and-fill mining has been used.This underground mine has two vertical shafts used for ventilation, ore hoisting, and for personnel and material transportation. Development drifts were designed and driven to extract and transport the ore, as shown in Figure I. Bolts, mesh, and shotcrete have been applied in this mine for ground control. In order to reach various locations, the tunnel system is designed with different heading directions and inclines, which will be described in detail later. The area selected for modeling is a cubic region including all the tunnels inside the black square (Figure 1)."

Jan 1, 2016

By Sandin Phillipson

During the course of ground control evaluations conducted by the Mine Safety and Health Administration's Roof Control Division, a number of surface and underground coal mines were visited that exhibited instances of ground failure associated with joints. The evaluations were conducted over a broad geographic area, including the Appalachian Basin from Pennsylvania to Tennessee, and they documented that joints occur in a wide variety of mining conditions and exhibit a wide variety of characteristics. Despite minor local variability in orientations, the joints fit into a cohesive pattern when evaluated on a regional scale in context with the system of thrust faults that define the Alleghany Front. Joints documented for this study, together with joints in sandstone and coal and the trends of drag folds compiled from other studies, were plotted on regional maps using GIS software. The trends of joints, including those that could be described colloquially as "hill seams," were not only parallel to regional fault systems and local trends of drag folds, but were also parallel to the regional patterns of previously mapped joints in sandstone and coal. These observations indicate that the features referred to informally as "hill seams" are in fact joints formed in response to tectonic processes associated with regional deformation of the Cumberland-Allegheny Plateau. The 286-266 million-year-old age of regional deformation significantly pre-dates the time when the Cumberland-Allegheny Plateau was subjected to deeply incised stream valley erosion, which began 25 million years ago. This challenges an existing interpretation that "hill seams" represent local ·stress relief joints that formed when stream valley erosion removed confinement and allowed tensile failure of the rock. Although relaxation of confining stress can reasonably be expected to occur near outcrop, observations indicate that this results in the dilation of existing joints. This paper presents instances of ground failure associated with joints, discusses methods of mitigation, and recommends that the term "hill seam" be abandoned in technical communication because it simply refers to a kind of joint that may exhibit certain weathering and aperture characteristics.

Jan 1, 2010

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

By Bingjie Huo

"China is a major coal producer and consumer. It is necessary to mine the steeply pitching coal seams due to development of the coal industry to meet the increasing needs for coal. Flexible shield supports mining is a safe and efficient mining method for steeply pitching coal seam that was first applied in HuaiNan mining area in the 1970s. The coal seams are steeply pitching in DaAnShan Colliery, so mining is mainly done by the flexible shield supports method. The roadway lay-out and extraction technology are researched in order to improve the safety, yield and work efficiency in the flexible shield supports working face. Optimization of the flexible shield supports mining method is discussed. The main optimization aspects are as follows: (1) the angle of working face and mining track roadways are increased from 23° to 28°, and (2) the technology and parameters of coal breaking are optimized. Applicable conditions, as well as advantages and disadvantages are also discussed. Finally, a comparison is made of the two different flexible shield supports mining methods, namely ""bench blasting . technology"" and ""piecewise blasting technology"".INTRODUCTIONChina is the largest producer and consumer of coal in the world and relies heavily on coal for energy production. At present, Chinese production is about 42% of the worldwide production, and coal has accounted for 76% of primary energy production. Coal plays a dominant role in the structure of energy production and consumption, which is fuel and an important industrial raw material but it is non-renewable. In recent years, the high inclined seams (35°< angle of coal seam < 45°) and steeply pitching coal seams (angle of coal seam >45°) have drawn increasing attention in the mining sector along with the growth of coal mining. There are two reasons. First, there are abundant reserves of high inclined and steeply pitching coal seams in China, which account for 15- 20% of total reserves (Xie, Dong-hai, 2007). Highly inclined and the steeply pitching coal seams are mined in more than 50% of the western mining provinces such as Sichuan, ChongQing, YunNan, GuiZhou, XinJiang, GanSu, NingXia, etc. As the mining of mineral resources continues west in the 21st century, the study of coal mining in high inclined seams and steeply pitching coal seams will be of great importance. Secondly, better quality coal has become scarcer in the eastern mining areas after years of exploitation, so steeply pitching seam mmmg is growing more prevalent. In short, carrying out research on steeply pitching seam mining technology plays an important role in sustaining the development of the Chinese coal industry."

Jan 1, 2010

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By X. L. Yao

This paper analyses the effects of mining extraction geometry (width/depth ratio) and dip of seam on subsidence parameters based on a large Database, containing 120 longwall mining cases all within the UK coalfields. The subsidence parameters evaluated in this paper include the following: the maximum subsidence value with different goaf-treatments, the position of maximum subsidence, the position of half-subsidence, subsidence value over the rib-side, positions of maximum tensile strains, positions of inflection points and the magnitude of maximum tensile strains on both rise and dip sides. Additionally, the maximum compressive strain and two limit angles are also studied in this paper. Based on a comprehensive Database analysis, several equations are derived relating these parameters to the width/depth ratio and the dip of seam. The results should assist engineers to design new structures, or take measures to protect existing structures from strain effects. The findings of the research assist in extension of the SEH to inclined seams with greater certainty.

Jan 1, 1990

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on &apos;stress balance&apos;. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981