Search Documents

The National Institute for Occupational Safety and Health conducted laboratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing. Laboratory results show that nearly 100 percent of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

By R. W. Chappell, M. W. Hills, R. L. Olsen

A stochastic approach was developed and applied to the Butte, Montana Hillside abandoned mining site for modeling stormwater runoff and subsequent receiving stream loadings. This approach enabled capture and quantification of the uncertainty associated with stormwater quality data and allowed the prediction of copper and zinc concentrations in the receiving stream caused by runoff from the Butte Hillside during storm events. Runoff flows and stormwater concentrations were input to the model as probability distribution functions. Monte Carlo simulation allowed prediction of expected instream concentrations in the form of cumulative distributions functions. The modeling results allowed evaluation of current best management practices (BMPs), targeting of future BMPs, and identification of key data gaps to fill during future sampling activities. This modeling approach is considered extendable to other active and inactive mining sites. Output from a model of this type is easily understood and can be used to communicate effective stormwater management to site regulators. Furthermore, application of this modeling approach will facilitate the development and implementation of a site-specific stormwater management plan and will optimize efforts to achieve standards for compliance with stormwater discharge permits.

Jan 1, 2002

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

By T. McCallum

Crud is a common concern in SX processes and is formed as a complex solid stabilized emulsion of aqueous and organic.1,3 Crud formation is highly dependent on the amount of solids entering the circuit and is influenced by a number of other operational factors. A common practice for crud processing is interfacial pumping, wherein crud, organic, and aqueous are pumped from the settlers for treatment and utilizes a variety of equipment. These mechanical means of crud processing are effective, however, require significant processing time and require oversight to prevent the return of contaminated organic. Cytec has developed a unique crud treatment process utilizing both chemical and mechanical means to enhance the solid/liquid separation. The use of ACORGA CB? 1000 crud busting reagent allows a rapid separation of solids from the organic phase and provides similar volume recovery to current practices. The process allows operations to return clean organic back to the plant more efficiently and may enable operations to process more crud. In addition, the organic quality of the recovered organic is higher than that recovered by typical means, which can lead to operational cost savings.

Feb 27, 2013

By M. Superfesky, P. Michael

Introduction The US Office of Surface Mining (OSM) is proposing changes to the Code of Federal Regulations in the interest of minimizing the adverse effects of excess-spoil-fill construction on the “prevailing hydrologic balance, fish, wildlife and other environmental values” (70 FR 35112). The proposed changes will require: (1) minimization the amount of excess spoil generated at a mine site; (2) minimization of the size of the fills constructed; (3) consideration of alternative configurations for disposal; and (4) development of a disposal plan that would minimize adverse impacts to the environment.1 To achieve those objectives, mining companies operating in steep-sloped Appalachia will likely build excess spoil fills (also called valley fills) that toe out at higher elevations in the hollows (i.e. to prevent or limit burial of streams). Consequently, the slopes of fill foundations will generally be steeper. Whereas the authors of this paper support these measures to protect the hydrologic balance and general environment, we wish to point out that placement of fills on steeper foundations can negatively impact the stability of the fills if proper care is not taken during their construction. It is important to note that in addition to impairing human safety, valley fill instability can negatively impact streams, the riparian habitat etc., and thus defeat the very purpose of the spoil minimization measures proposed. We do not, however, propose additional regulatory requirements pertaining to valley fill stability. Rather, we intend to emphasize the importance of engineering requirements already on the books, especially as they apply to the predominant type of valley fill constructed: the durable rock fill. We believe that the practice of restricting valley fills, to higher elevations in the watershed leaves less room for error in the design and construction of stable structures. This paper gives a quick review of the nature of excess spoil generation; methods and requirements of excess spoil fill construction, and the to-date stability record of the fills. The interest in excess spoil minimization and how it affects valley fill construction is also discussed. Most importantly, we will review long-standing issues pertaining to proper design and construction measures with respect to durable rock fills and discuss how they will become more critical as spoil minimization is practiced.

Jan 1, 2007

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Narendra N. Khatri, Michael Deutscher, Jozef F. Zurawski

Five sewer connections were required to divert Combined Sewer Overflow (CSO)from existing outfalls to an old underutilized large diameter brick sewer (the Easterly Interceptor). The connections were part of an on-going CSO control program by the Northeast Ohio Regional Sewer District (NEORSD) in the City of Cleveland, Ohio. Each connection was made by pipejacking and hand-mining a fiberglass-reinforced polymer (FRP) pipe through soft glaciolacustrine clays and silts. Jet grouting was utilized to stabilize the soils and fill the voids surrounding the interceptor prior to making the underground connection. Reinforced concrete liners were constructed inside the aging brick sewer to provide structural stability during ground improvements and connection work. The project also involved micro tunneling two approximately400 foot lengths of FRP pipe through soft ground using a slurry pressure balanced machine.

Jan 1, 2005

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam&apos; (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today&apos;s inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government&apos;s offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009