Search Documents

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By A. Bruynesteyn

I would like to talk to you today about microbiological leaching or, the solubilization of metal values due to the action of Thiobacillus ferrooxidans. Bacterial attack of sulfide minerals has been going on for centuries but only recently was it discovered that the acid and iron often found in coal mine drainage is produced by bacterial action on the iron sulfides in the coals. Not until 1950 was it proven that bacteria were playing a role in the dump leaching of sulfide ores. B. C. Research became involved in microbiological leaching in 1955 while examining mine drainage from the copper-zinc mine at Britannia Beach, north of Vancouver. Since 1955, B.C. Research has maintained a continuous re¬search program on microbiological leaching which, due to its applied nature, was put under industrial sponsorship in 1962. Most of the information pro¬vided in my talk today has been gathered under this sponsored research program and I would like to express our appreciation to the many sponsors who have made our work possible.

Jan 1, 1970

By James C. Bradbury

Tripoli is a naturally occurring, finely divided form of silica found chiefly in midwestern and southeastern states and used commercially in fillers and abrasives. The name comes from the location of a silica deposit in North Africa and was applied in the latter part of the 19th century to similar material near Seneca, Missouri. Subsequently, the North African material was found to be diatomite, composed of siliceous skeletons of microscopic marine plants called diatoms, and the material's name was changed to tripolite. The name, tripoli, remained with the Missouri silica, which is inorganic in origin, and tripoli is now used to designate all naturally occurring silica that is similar in characteristics and origin to the Missouri material. Just to confuse things further, in commercial trade tripoli usually designates silica from the Missouri-Oklahoma field, whereas silica from southern Illinois, the other major producing area, is called amorphous silica. Each term, however, may be used commercially for any material, regardless of place of origin that has the characteristics or uses ascribed to material from either major producing area. For example, Engineering and Mining Journal routinely lists under "tripoli," prices "f.o.b. Elco, I11." and "f.o.b. Seneca, Mo. and Rogers, Ark.", and under "silica, amorphous," prices "f.o.b. I11 and "f.o.b. Dierks, Ark." "Soft silica" is another term that has been applied to tripoli from Illinois, west central Arkansas, and Tennessee, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, which is produced by pulverizing silica sand. Tripoli is produced mainly in extreme southwestern Illinois, in the Missouri-Oklahoma district in Newton County, Missouri, and Ottawa County, Oklahoma; and in the novaculite belt of west central Arkansas. Some tripoli is produced for local and specialized uses near Austin, Texas.

Jan 1, 1980

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By R. J. Reuss

The ore at this new underground operation is a massive sulfide breccia with high copper values. A major highway and electric transmission line pass directly over the near-surface orebodv. The mining method being used is undercut and fill. A continuous miner together with a single boom, hydraulic jumbo is used for the mining. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation.

Jan 1, 1992

By C. V. Deutsch, J. B. Boisvert, J. L. Deutsch

Data used to build geostatistical models come from a wide variety of sources with potentially differing sample errors and volume supports. Typically all available sample measurements are pooled together for statistical analysis irrespective of the quality of the data. The sample data is used to assess spatial continuity, make local estimates and assess uncertainty. A new methodology is proposed to simplify accounting for samples of differing quality. The result is improved estimates with higher weights assigned to high-quality samples, while low-quality samples receive less influence in resource estimation. A new dimension, d, is introduced and calibrated to account for sample error and/or volume during estimation. The addition of an extra dimension can be easily incorporated in existing kriging or inverse distance workflows. The only additional parameters required are the sample error and volume for each datum. The methodology is demonstrated and the improvement in local accuracy is documented. Extending the dimensionality of the domain to four (three spatial dimensions and the additional d dimension) requires a valid 4D variogram model; therefore, the spherical variogram model is generalized to arbitrary n-dimensions.

Jan 1, 2011

By Wilfred Walker

A working hypothesis is presented herein mineral belts are split as all world oceans opened. Rather than plate tectonics, expansion is favored as the most recent expression of the sequence of convecting systems in the Earth's mantle. Throughout the geological record this sequence has produced similar mobile belts. This similarity lends itself to both stratigraphic classification and the theme of mineralization in mobile belts demonstrated by Y. A. Bilibin. Crustal evolution should, therefore, serve as an important guide in understanding Pacific mineral belts.

Jan 1, 1982

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

The engineering company's participation in quality assurance in the mining industry is twofold. Not only must it have such a program to ensure the necessary high standards for its own design and construction of a minerals processing plant, but it is also responsible as the "engineer" for both the selection and the quality of purchased equipment which goes into that plant. It is in this latter role that the engineer finds the most difficulty, or controversy, since while it is relatively easy to control his own performance, this is not ncessarily so when dealing with companies, all with their own ideas or standards. The engineer has perhaps rather reluctantly become more involved with the quality assurance of purchased equipment. This is because he has been used to writing performance type specifications and expecting the equipment manufacturer to provide the degree of quality, and control of that quality, for the product to meet the specified operating conditions. However, this has sometimes placed the manufacturer in a difficult position since to remain competitive in today's market conditions, he cannot always insist on product improvements or options which may in the long run be vital to reliable operation of the equipment.

Jan 1, 1982

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By Wen H. Su

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in a room-and-pillar working located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1984

By Frank W. Reinrniller

Mill ball charging systems have undergone little change during the past two decades. Most operations utilize a locomotive/ball car combination to load and haul charges from the ball storage bin to the mill charging boxes or, alternatively, transport charges to the charging boxes by means of a ball bucket handled by bridge crane. This paper describes a new concept in ball handling systems that is in operation at the Island Copper Concentrator of Utah Mines, Ltd. at Port Hardy, B.C. This system employs a narrow belt conveyor to convey a weighed charge to each of nine belt unloading stations at the mills. In operation, the system has proved to be practicable, trouble-free and economical of operating labor.

Jan 1, 1977

By David J. Barr

Public Law 91-190 - January I, 1970 states that, "The purposes of this Act are: To declare a national policy which will encourage productive and enjoyable harmony between man and his environment; to promote efforts which will prevent or eliminate damage to the environment and biosphere and stimulate the health and welfare of man; to enrich the understanding of the ecological systems and natural resources important to the Nation; and to establish a Council on Environmental Duality." The administrative aspects of this National Environmental Policy Act of 1969 have in essence established the requirement that all agencies of the Federal government assess the consequence of their actions with an Environmental Impact Statement. Furthermore, five states have already enacted environmental legislation, and others will surely follow. The Environmental Services Project Director for Dames and Moore has stated in the June issue of that company's publication, "Elements," that, "The nuclear power industry has perhaps been most affected to date by the Act [NEPAL but recent court decisions, legislative trends and general public concern will accelerate the spread of the Act's impact on other industries. Mining and petroleum are already involved in environmental affairs." There can be little doubt that within a very short time all environmental aspects of the minerals industry will be strictly regulated and monitored by some agency of Federal and/or state government. Indeed, it is probable that any future effort to extract natural resources will be contingent upon a favorable review of an Environmental Impact Statement. It is also quite possible that continuation of present operations will have to be justified on the basis of proof of an acceptable environmental impact. It is the objective of this paper to present some ways in which remote sensing technology can be applied toward an efficient collection of environmental data necessary for the preparation of an Environmental Impact Statement.

Jan 1, 1972

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion-resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Jan 1, 1997

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By A. L. Crandell

The Cortez Mining District has had a long history of mining activity dating back to 1862 as previously reported (1) (2). More recently Cortez Gold Mines (i) has operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the U.S. for treating higher grade finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1520 tonnes per day on oxidized ore from the Cortez ore body. Starting in 1973, the mill was operated at 2050 tonnes per day on softer, less oxidized, high clay ore from Gold Acres which is located 13 kilometers to the west of the Cortez installation. In February of 1976 the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operation. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Much valuable experience was gained in the operation of these two heap leaching programs and is well described in an earlier publication (3). Releaching of the ore heaps at Gold Acres and Cortez was continued with a limited crew from 1976 to 1979.

Jan 1, 1986

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By Phil Allen

A synthetic fiber manufactured by one chemical company has been treated by another chemical company to produce a cloth fabric capable of performing ion-exchange functions. Only a few delimiting parameters have been established. This paper will discuss briefly the highlights of a functioning ion-exchange cloth. Throughout the paper this fabric will be referred to as "Fabric Z".

Jan 1, 1970