Search Documents

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999

By W. D. Gould, . W. Koren, P. Bedard, P .. B. Marchant

Ammonia and nitrate in metallurgical operations arise from several sources: (1) the use of ammonium nitrate based explosives, e.g. ANFO; (2) the use of cyanide for gold extraction which is degraded to ammonia by most cyanide destruction techniques; and (3) the use of nitrogenous reagents in the mill for neutralisation, flotation and extraction. The concentrations of ammonia and nitrate in effluents vary from 10-50 ppm and 25-300 ppm respectjvely. A number of environmental problems are associated with both ammonia and nitrate. Both of these forms of nitrogen can contribute to the eutrophication of receiving waters. Ammonia and organic nitrogen can also cause high dissolved oxygen demands in receiving waters. Ammonia is also toxic to fish, particularly at elevated pH values. Several methods are in use for the removal of ammonia and nitrate from municipal wastewater, industrial effluents and agricultural runoff. To date, no treatment systems have been developed specifically for the removal of nitrogen from mine and mill effluents. This paper will report on some removal techniques that have been tested using actual and synthetic mine effluents.

Jan 1, 1993

By S. J. Knoll, D. F. Scott, T. J. Williams

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep under-ground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By George A. Lawrence

A new super-large 100 m3 (3500 ft3) pneumatic mechanical flotation cell is now available to meet today's mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom round tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. The mechanism drive is either a customized right angle gear reducer or a conventional Vee belt drive. Both drive systems are available with an optional variable frequency control system that permits infinite speed adjustment of the rotor in each flotation cell or group of cells. Results of side-by-side comparative testing between three major manufacturers of super-large pneumatic mechanical flotation cells are discussed. These results were obtained at a large copper concentrator in Chile during several weeks of commercial scale testing.

Jan 1, 1995

By Menzhans Guo

A coal bunker basically acts as a buffer and regulator to reduce the interruptions between its proceeding production system and succeeding haulage system so as to maximize the availability of the whole system. Although such a role has long been recognized, quantitatively studying it is still rarely seen in the literatures. Its unique characteristics, coupled with numerous transitional states, make it very complex to describe the state transitional process in analytical models and, also very difficult to seek an analytical solution. Moreover, the analytical models inappropriately consider the state of bunker being full or empty as a kind of failure, therefore, by no means can they realistically describe the impact of the difference between rates of coal flowing to and from a bunker on the system availability. In light of this, Monte Carlo simulation methods are suggested to reach an approximate solution. In comparison, simulation methods are simpler and more effective than analytical approaches. Applications of simulation methods to a Northern colliery for determining bunker size from the viewpoint of maximizing system's availability are discussed. The results are satisfactory.

Jan 1, 1992

By Bernard Lippe

The successful construction project is one in which the component construction operations are completed within the scheduled time and cost parameters. Most construction projects, however, are subject to delays and/or disruptions which adversely affect the time (start, duration, and completion) and cost aspects of the project. DELAYS Delays fall into two categories: Compensable Delays for which the contractor is entitled to contract time extensions and additional money as compensation for the extra expenses generated by the delay or obstruction to job progress, and Non Compensable Delays, for which the contractor may or may not receive an extension of time but no additional compensation. Compensable Delays Compensable delays may take the form of holds or suspensions on all or certain segments of a project by the owner, failure of the owner or his Engineers to approve shop drawings, cuts or material samples within a reasonable period of time, failure of the Owner or his Engineer to properly coordinate the job, discovery of design deficiencies in the plans and specifications which prevent the continuation of construction until

Jan 1, 1974

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents and particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and conditioning time, were investigated to determine their effect on reagent coating of the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power (P) to the minimum power (Pm) required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain a high recovery. Reagentization was slower at lower P/Pm ratios. At higher P/Pm ratios, the flotation recovery was optimized, and the agitation speed was found to have no significant effect. Optimum mixing conditions were obtained for a74 wt% slurry at an agitation speed of 450 rpm (47 radians/sec). Under these optimum mixing conditions, the collector dosage required for an improved recovery was lower and the conditioning time was shorter.

Jan 1, 1997

By Eugene F. Casey

The next ten to fifteen years will be exciting ones for the construction industry because three city agencies alone have started or will start, on tremendous expansion programs, the cost of which will exceed a total of four billion dollars. The major portion of this work will be done by the use of tunnelling methods. *Tunnelling is construction by any method of a covered cavity of predesigned geometry whose final location and use under the surface, whose cross-sectional area is greater than two sq. meters. The New York City Transit Authority's expansion program will provide for approximately 52 miles of new subways. The Board of Water Supply has already started on City Tunnel No. 3 which, when completed will provide the City with enough water until the year 2000, and the Board of Water Resources has embarked on a tremendous program to clean up the surrounding waters. Yes, these will be exciting years, particularly when one reads about the new novel exotic methods of rock breaking and disintegration, coupled with the new methods of soft ground tunnelling.

Jan 1, 1997

By John M. Marek, David E. Nicholas

INTRODUCTION The purpose of this article is to outline the data requirements for selecting a proper underground mining method and to discuss the general steps taken in selecting that method. Determining the appropriate mining method is an iterative process that continues throughout the life of a mineral deposit. We will discuss the subject from the standpoint of a feasibility study, where a realistic assessment is necessary in order to determine investment merit. The feasibility stage of a project is that point where the drilling program has defined sufficient geologic reserves to consider mining the deposit but little or no underground development has been done. Primary parameters for consideration in choosing a mining method are 1) geometry of the deposit; 2) distribution of grade; 3) rock mass strength for the deposit, as well as the hanging wall and footwall; 4) mining cost and capitalization requirements; 5) mining rate; 6) type and availability of labor; 7) environmental considerations; and 8) other site-specific conditions. Of these parameters, the first four have the most impact on determining the general mining method to be employed.

Jan 1, 1981

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By Gordon M. Elliott

Health risk underlies all of today's environmental regulations. Mine Manager's are no strangers to risk, but risk in the context of mine management is not the same as risk in the context of environmental regulation. One of the risks facing the mine manager is whether the mining operations meet environmental compliance standards. These standards are defined in terms of the frequency of occurrence of adverse health effects in an exposed population (i.e., health risk). Demonstration of compliance necessarily involves mathematical modelling and selection of values for input variables. What is not immediately apparent is that the method of estimating the human health risk has a significant influence on remedy selection and the amount of money spent at suspected contaminated sites. Using a hypothetical, mining-related example, this paper illustrates the disassociation between the current deterministic approach to health risk assessment and cost-effective decision making. This paper also illustrates how the probabilistic approach to health risk assessment provides a more realistic characterization of health risk and enables mine managers to identify cost-effective remedial strategies for the site.

Jan 1, 1992

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By Richard W. Hornung, Steven Samuels

A great amount of work in recent years has been devoted to refining older survivorship models, e.g. life tables, and developing newer ones, e.g. Cox regression. In this paper, these models are applied to data from an epidemiological study of uranium miners in four western states conducted by the U.S. Public Health Service. One of the principal problems addressed in this paper concerns the appropriateness of using cumulative dose as the measure of radiation exposure. An alternative is considered that incorporates dose rate into the model. This procedure does not implicity assume that equal cumulative doses produce the same lung cancer mortality, but instead considers the amount of time in which each miner's dose was accumulated. Results of the statistical analysis indicate that dose rate is a significant factor at higher cumulative dose levels, with lower dose rate apparently more damaging than higher dose rate. The shape of the dose response curve is curvilinear at higher dose levels. No interaction was found between smoking and radiation exposure on a multiplicative or relative scale.

Jan 1, 1981

By Howard M. Wells

The future is uncertain. In these circum- stances how can we rationally decide whether to commit funds to an investment that may or may not turn out to be successful? To date no certain answer to this problem has been found, nor is one likely to be found in the future. At best we can attempt to assess the possible outcome in terms of probability, taking into account all sources of information that may be available at the time the decision must be made. This subject is addressed with some trepidation and much humility. Any attempt to fore- tell the future is by its very nature controversial. The purpose of ' this .chapter is to present a proposed rationale for decision making under uncertainty which relates the probabilistic risk of the investment to the capacity of the firm to absorb possible unfavorable consequences if they should occur. It is not the intention to propose a cut-and-dried methodology but rather to examine the conceptual philosophy on which a methodology may be based.

Jan 1, 1979

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By K. I. Cunningham, C. S. Spirakis

Two types of native sulfur deposits have been found in Lechuguilla Cave: thin late-stage crusts and massive early- formed deposits. Most, if not all, of the crusts appear to have formed by remobilization of native sulfur contained within gypsum and sulfur masses. The process is occurring today and is slowly converting the sulfur to gypsum. The absence of primary gypsum or reductants in the cave indicates that the early-formed massive sulfur deposits did not form by in-place reduction of sulfate, which is the process that formed the commercial sulfur deposits in the Delaware basin. Instead, it appears that H2S dissolved in basinal brines was oxidized by oxygen in near-surface ground waters in the cave. Fluid- inclusion data, which suggest the presence of both fresh water and saline water as the sulfur formed, support this interpretation. Although individual sulfur deposits in Lechuguilla Cave are no more than several tens of metric tons, the abundance of secondary gypsum (as much as 10 meters thick) indicates that native sulfur may once have been much more extensive.

Jan 1, 1992

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987