Search Documents

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increasing usage for acid mine drainage mitigation as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1998

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By T. P. McNulty

During the last decade, many exhaustive studies have been made of process energy requirements for the production of various metals and materials. Some excellent technical papers and text books have resulted, and some of these are included in the bibliography of this paper. These studies were, of course, prompted by the economic pressures which resulted from the beginning of the "Energy Crisis" in 1973. Our intensified consciousness of the cost of energy led, then, to a greatly improved understanding of the energy consumption attributable to individual mining, processing, and refining steps. It is worth noting, however, that an awareness of the cost of energy is not new and that efforts to minimize this cost were an important part of sound mine and plant management practice throughout the earlier days of our industry. One only has to read a few accounts of mining operations around the beginning of this century to develop an appreciation for the cost of supplying wood, coal, fuel oil, or electric power to remote locations.

Jan 1, 1983

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By Michael R. Grubbs

In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper. A new metal separator was recently reported by t. Schlömann1. The author described the theoretical relationships and presented results of tests on samples of the residual fraction of municipal solid waste. This paper describes the operation of the metal separator and develops the basic separation relationships controlling the process.

Jan 1, 1976

By Roger P. Ashley

The main problem in geochemical exploration for gold ore bodies in the 40 km2 hydrothermally altered area at Goldfield is to decide which of the many silicified ledges exposed are most likely to yield deposits with additional subsurface exploration. We conclude that the most efficient way to search for exploration targets is to collect rock samples from the ledges and analyze for the following elements in decreasing order of priority: gold, lead and silver, bismuth, and mercury. These elements form relict hypogene aureoles restricted to the ledges and are not appreciably redistributed during supergene leaching.

Jan 1, 1978

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in there two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section 1 of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the anti¬trust laws is entitled to recover treble damages plus costs.

Jan 1, 1966

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By A. V. Castelli

Since the record year of 1981 through 1985 the tonnage of weighting materials (barite and other heavy minerals) used in drilling fluids has decreased an estimated 49%. As in the past, barite still makes up over 90% of the minerals used for weighting materials in drilling fluid. Domestic production of barite has decreased 69% since 1981 and imported barite has made up over 50% of the total barite consumed since 1982. See Figure 1 for usage of barite. The number of operating grinding plants has decreased from 69 in 1982 to 39 at the end of 1985. With the decrease in demand of weighting materials for drilling fluids and an over capacity of grinding existing, prices for weighting materials have decreased dramatically. Although the American Petroleum Institute has not changed any of the specifications for barite, some users have initiated their own new specifications and have proposed to have them included in the API specifications. The exploration for and development of oil and gas dictates the level of weighting material used in the drilling fluids industry. Most forecasters do not foresee (or predict) increases in the level of drilling until the 90's. The primary or unground barite produced in the U.S. mines has a difficult time competing with imported barite due to the location of the mines. These mines are located in North Central Nevada, with small tonnages being produced in California, Missouri, Illinois, Montana and Washington. The major reason, is the difference in transportation costs from the mines versus ocean freight rates from the foreign ports to the major area of use, the U.S. Gulf. Since 1981, the production of primary barite has decreased from 2,849,000/ST (2,584,596/MT) in 1981 to an estimated 890,000/ ST (807,403/MT) in 1985(1). If it were not for the use of unit trains by some producers the production of primary barite in the U.S. would have probably declined another 20% in 1985. During the same period, of the total amount of barite consumed in the U.S., imported barite ore increased from 417, in 1981 to 65% in 1985. The major exporting countries to the U.S. during this period were China 46.27, Morocco 15.27., Chile 10%, Peru 8.4%, India 7.9%, Mexico 5.4%, Thailand 3.9% and Ireland 2.3%.

Jan 1, 1986

By Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comninution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5 x 6.4 m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790 to 1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By J. P. Kennedy

Process data managers or historians are recognized as essential for reengineering projects in industrial plants. With increasing automatic data collection, the knowledge of how to use these data profitably grows as well. This paper is a summary of the data historian and its components plus examples of benefits including environmental reporting, performance monitoring, and exception reporting to management.

Jan 1, 1994

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By Clement K. Chase, Manuel R. Lastra

Introduction The choice of using a dump or heap leaching process or a fine grinding-agitation leaching process is based on the grade and tonnage of the ore body. Low grade ore and small tonnages are best treated by a low-cost method, such as dump or heap leaching. Permeability, however, is the critical factor in a successful leaching operation, regardless of tonnage or grade. Without permeability in the leach bed, no percolation, no dissolution, no extraction, and no success are possible. Solution delivery to the ore is also essential. Solute-to-mineral contact is a requisite. The solute must be effectively strong and not be depleted in active dissolvers, such as acid, ferric iron, cyanide, and oxygen. It must also be moving across the mineral to be dissolved. No pockets of stagnant solution can be allowed. A third factor is recovery of the now-dissolved metal in the pregnant liquor. All such liquor should be gathered at a reasonable metal concentration to make further pumping and processing worthwhile. Control and recovery of pregnant solutions are probably the most ignored factors of solution mining. This stage in recovery is historically where many operations either fail or become viable. Permeability A permeable heap is normally achieved by taking into account heap building/construction and agglomeration/pelletizing. Even though heap building is critical for good permeability, it will not be discussed here. It has been described in detail by others. Instead, this analysis will concentrate on agglomeration and pelletizing. Differences between agglomeration and pelletizing are emphasized. Agglomeration is referred to when small particles are being attached to larger particles -the ore presents a complete size distribution. On the other hand, pelletizing is a process where all particles are fine (less than 850)µm or 20 mesh), as with mill tailings. The difference is important from two points of view: • Mechanical devices used to achieve the desired attaching action; and • Binder dosages. Mechanical Devices Due to the absence of large particles that fines can become attached to, pelletizing should be done in a centrifugal-action-based device, such as an inclined rotating plate, a rotary drum, or a series of belt-transfer points. In agglomeration, large particles play a part as a natural nucleus for the attaching action of fines. Hence, a tumbling action as strong as for pelletizing is not required. Common methods to accomplish agglomeration include: • Cascade belt system with either all belts moving forward or some of them moving forward and at least one moving backward; • Combination of belt plus inclined vibrating chute; • Large concrete mixer drum; and • Belt discharging directly onto stockpiled ore. The proper agglomeration system will depend basically on the size distribution of the ore and the amount and type of clays present. In all of the agglomerating systems described, the tumbling action takes place at the transfer points either from belt to belt, or from belt to inclined chute ore belt to ore pile. Usually, two or three mixing bars at each transfer point are also included to help the mixing action. Plows to move the ore around on a moving belt are also used.

Jan 11, 1984

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988