Search Documents

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By Donald D. Carr

Four counties in Indiana--LaPorte, Vigo, Vanderburgh, and Switzerland--have potential for deep underground limestone mining because they are in or are near high population areas and have no surface-minable limestone de- posits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Minable seams suitable for aggregate are 120 to 150 meters (400 to 500 feet) below the surface in LaPorte and Vigo Counties, about 90 meters (300 feet) below the surface in Switzerland County, and about 600 meters (2,000 feet) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1980

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

The last decade has seen the use of powerful computerized Mine-Wide Monitoring (MWM) systems for detecting hazardous conditions in underground coal mines. Recently, the U.S. Bureau of Mines and Jim Walter Resources, Inc. (JWR) expanded the scope of MWM system to include ground control. Single-point extensometers were installed in each of 30 intersections along a tailgate entry. These instruments monitored the rate of roof sag, a sensitive indicator of roof instability. Data were collected by the mine's own computerized MWM system. The paper describes the successful integration of ground control instruments into MWM, the data reduction procedures, and the identification of several hazardous areas.

Jan 1, 1994

By Stanley W. Ivosevic

The South-Central area of the Osa Peninsula, Puntarenas Province, on the Pacific coast of southern Costa Rica, may have produced on the order of 30,000 kg (100,000 troy oz) of gold since prehistoric times. The Peninsula lies along an 800- to 900-km-long belt of late Mesozoic eugeosynclinal rock deposition, hydrothermal activity, and deformation (Campanian). The oldest rocks exposed in the area are basalt and tuffaceous mudstone of the Late Jurassic or Cretaceous Nicoya ophiolite complex. The Nicoya Complex is overlain by weakly lithified Pleistocene Older Sediments, predominantly conglomeratic sandstone and derived from erosion of the Nicoya Complex. Erosion reduced the Complex to a surface of high relief, so that the detrital source was in the area originally; the source retreated with subsidence. Stratigraphically, the Older Sediments are followed by surficial deposits of intermediate age, consolidated Younger Sediments reworked from Older Sediments, and unconsolidated Holocene surficial deposits reworked from Younger Sediments. The most prominent structures are a northeast-trending anticline and northeast and northwest fault sets. Some deformation was Cretaceous, but folding and much faulting occurred after deposition of the Older Sediments. Remnants of plainlike features and destructional terraces on the Older Sediments attest to stepwise downcutting of the terrain during successive stages of uplift. Near the end of this process, the present valley floors and coastal headlands developed. During a probable epeirogenic rise in sea level, Younger Sediments filled the valley bottoms and an aggradational coastal plain developed. Sea level dropped by stages and with some reversals to its present position; this caused stepwise incision of the valley fill, stepwise beveling of the coastal plain, and development of the present wave-cut platform. Spilitization around the time of the Campanian orogeny caused some parts of the Nicoya complex to be calcitized and others to be silicified. Gold, pyrite, and probably additional silica were introduced during subsequent hydrothermal activity. Native gold was eroded from Nicoya Complex lodes and reconcentrated through three generations of placer gold deposits. First, the gold was deposited as a detrital.

Jan 1, 1977

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By M. F. Martin

Dewatering aids are chemicals which enhance the efficiency of mechanical dewatering equipment such as vacuum disc filters and centrifugal dryers. A new dewatering aid has been developed which significantly lowers the moisture content of the mineral concentrate and causes none of the undesirable side effects normally associated with dewatering aids. Highlights of product development from laboratory screening through field testing will be discussed.

Jan 1, 1985

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By M. S. Celik

Salt-type minerals are usually floated with anionic and cationic collectors. Flotation of a number of systems has been reported to remarkably increase above the concentrations where surface precipitation of collector-metal salt is initiated. Some studies attribute this phenomenon to heterocoagulation of oppositely charged collector colloid and mineral particles. In this study, examples are given on boron minerals to demonstrate that the high flotation region occurs when particles, colloidal precipitates and bubbles acquire a similar charge which induces Van der Waals interactions resulting in hydrophobic bonding.

Jan 1, 1995

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By A. D. Davis

The Bear Butte Creek watershed, in the northern Black Hills of South Dakota, shows the effects of past mining activities in the form of dissolved metals and arsenic in stream water. Bear Butte Creek, during normal flow periods, loses all of its discharge to sinkholes that recharge the Madison Limestone aquifer. This work focused on the geochemical transport and fate of arsenic and on understanding ground-water flow conditions in the Madison aquifer through development of a three-dimensional ground-water flow model that was coupled to a geographic information system (GIS). Stream sampling and discharge measurements helped determine sinkhole losses and loading rates. Column laboratory tests provided data on arsenic adsorption and the mixing of stream water with aquifer water, which also was simulated with the geochemical models, pHREEQE and NETPATH. The models and GIS can be updated with new information and will be useful in managing the water quality of the Madison aquifer.

Jan 1, 1997

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By O. W. Kamper

To most of you present here the word "refractories" is not new and you are familiar with the materials and use. To many people though the question is asked, "What are refractoriness and what are they used for?" Refractories are non-metallic products which are so resistant too melting at very high temperatures that they can be used for building or lining furnaces of all kinds. A large variation occurs in the size, form, and composition depending on the service for which they are intended. They are made from a wide variety of raw materials, of which fire clay and quartzite are used in largest quantities. Other refractory raw materials include magnesite, chrome, diaspore, bauxite, kyanite, sillimanite, olivine, zircon, and many others. Most of these are assembled from-widely-'separated points in the United States while others come from the far corners of the earth. Chrome is imported from the Philippines and South Africa, and, to a lesser extent, Turkey and Greece Kyanite and sillimanite come: from India and bauxite from the Guianas. And there's "magnesite from brines," produced in chemical plant's by treatment of sea water or inland deep-well brines with hydrated lime. The proportion of magnesia available in sea water is so small, less than one pound from 500 pounds of water,, that millions of gallons must be pumped and processed each day in a sea water magnesite plant. The realm of refractory raw materials, therefore, is very extensive and continues to grow because of the endeavor to find-better raw materials from which to produce better products for refractory service.

Jan 1, 1960

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023