Search Documents

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By David S. Bolin, Bruce Kennedy, Leigh A. Readdy, Graham Mathieson

INTRODUCTION The estimation of ore reserves is a process that begins with the earliest exploration stages on a property and continues throughout any subsequent evaluation and exploitation of the deposit. During exploration and preliminary evaluation, the results of these reserve estimates constitute the basic data for prefeasibility studies and economic analysis. The decision to continue exploration and development or to abandon a prospect is often based upon these studies. During the active life of a mine, reserve computations are continuously revised to assist in development planning, cost and efficiency analyses, quality control, and improvement of extraction and processing methods. Accurate reserve estimates are also required when financing a project, purchasing or selling a property, and for accounting purposes such as depletion and tax calculation. It is important to remember that the reliability of ore reserve estimates varies progressively through time as more and more information becomes available. The lowest order of reliability of estimation of reserves exists at the time of discovery. The maximum level of certainty concerning the ore reserves within a deposit is reached when the deposit is completely mined out. Between these two extremes are variable levels of certainty as to the tonnage and grade of the resource. This is particularly true of that portion of the mineral resource that constitutes the "minable reserve," as this portion is dependent upon economic as well as geological and technological factors. In the following discussion, several of the factors affecting ore reserve computation and some of the commonly used methods of calculation are presented. The first part of the discussion is confined to classical methods of hand calculation utilizing level maps and sections. The second part of the discussion presents an overview of somewhat more sophisticated methods of geostatistics which have been developed within recent Years. Geostatistical methods frequently provide the best ore re- serve estimates for many deposits. However, a digital computer is required for such geostatistically derived estimates due to the number and complexity of the cornputations involved. For many properties the classical nongeostatistical methods are adequate, particularly in the early exploration stages. In fact, it is the author's contention that even at those properties where the geostatistical approach is employed for reserve estimation, the geological and engineering staffs should prepare an estimate by traditional means. This provides an internal audit for the reserves and at the same time requires a continuing close appraisal of geologic problems that influence the presently known geostatistically estimated reserves and production at the mine.

Jan 1, 1982

By S. E. Phillipson

Slickensides cause potentially hazardous ground conditions in underground coal mines. Investigations by MSHA’s Roof Control Division indicate that many slickensides represent bedding plane faults and drag folds that formed during coal bed decollement, a style of faulting that occurs in shale units above coal seams. These slickensides formed in response to regional tectonic compressional stresses, rather than by differential compaction, and are parallel to folds and thrust faults. This paper relates slickensides in the Appalachian, Illinois, and Black Warrior basins to the structural grain of the Appalachian Mountains, provides descriptions of slickensides, and advocates geologic mapping as a predictive method for identifying areas with adverse ground conditions.

Jan 1, 2003

By Jamal Rostami, Jürgen Schmitt, Rohola Hasanpour

"Double Shield TBMs can be used in fast track projects for accelerated completion where there is limited information available on ground conditions and there are possibilities of encountering weak ground and shear zones. As such, the shielded TBMs are the primary choice of the machines in long tunnels, but face the possibility of entrapment in squeezing ground, which entails long delays and major risks. This paper examines the possibility of using ground improvement methods to increase ground strength, and thus, increase the capability of the machines to cope with squeezing ground conditions. In this study, 3D finite difference simulation of a shielded TBM in squeezing ground was performed to estimate the operational parameters including required thrust to get a machine out of an entrapment. This analysis was also used to evaluate the possibility of preventing machine jamming by the implementation of pre-excavation ground improvement to increase the strength of the ground. INTRODUCTION In order to face adverse tunneling conditions especially using a shielded TBM in squeezing ground, new shield designs, with extra thrust and torque, step shield geometry with reduced shield diameter from front to the back, and conical shape shields have been used. In addition, many of the new machines have the capability to implement ground improvement at distances up to 50 m ahead of the face in order to reinforce the ground and further increase in their chances to cope with squeezing ground conditions. While these features have been added to the machine, there has not been a thorough evaluation of their impact on improving the chances to avoid machine jamming in weak rocks at high depth, which is conducive to rapid convergence of the ground."

Jan 1, 2016

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By A. Iordanidis

Mining activities have recently been taken place in Vourinos mountain, northern Greece, exploiting the so-called ?olivinite?. A representative sample was collected from this mining area. Mineralogical analysis was conducted using X-Ray powder Diffraction (XRD). A thin section was prepared and analyzed under optical microscope. X-Ray Fluorescence (XRF) was employed for the chemical analyses of major, mi-nor and trace elements. Environmental Scanning Electron Microscopy coupled with energy dispersive x-ray analysis system (ESEM-EDX) was also applied for the characterization of the sample. Forsterite (Mg-rich olivine) and enstatite (Mg-rich orthopyroxene) were the main mineral phases determined by XRD, with a 56% and 44% content respectively. Trace amounts of chromite spinels were also determined. Based on this characterization, the industrial rock proved to be a hartzburgite (a type of peridotite in petrological terms). Optical microscopy and ESEM-EDX provided similar observations and confirmed the above-mentioned results. XRF revealed a composition of 43.31 MgO, 44.25 SiO2, 9.98 Fe2O3, 1.40 CaO, 0.67 Al2O3, 0.22 MnO, 0.01 TiO2 and negligible amount of LOI (<0.1%). Trace elements with high concentrations were Cr (2678 ppm) and Ni (2044 ppm). The comprehensive characterization of this mining product suggested the suitability for various uses, such as refractories, foundry and slag conditioner. Additional experiments are being carried out for environmental applications, e.g. wastewater treatment.

Jan 1, 2006

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By P. Nelson, R. O’Connell, J. Rostami

Tunnel boring machine (TBM) system utilization is a critical factor for predicting machine performance. The process of estimating machine performance, including rate of penetration (ROP) and machine utilization (U) must incorporate an understanding of site geology, TBM specifications and site management. The study herein presents a preliminary analysis of the different activity time and downtime components from hard rock TBMs at two project sites to evaluate their impact on machine utilization. A comparison of crew experience, first between shifts and then between projects is included to analyze its effect on utilization and downtime. This work presents the sensitivity of the utilization factor to selected activities in the projects and the impact of geology and site set-up/logistics on machine performance.

Jun 13, 2021

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By William H. Bird

Over the past 14 years, the efforts of 2 companies and several individuals have outlined a major solfataric gold ore body in the Summitville district in the southeast San Juan Mountains of Colorado. The hard work of these years could not have flowered without a dedication to modern exploration methods, an intense interest in new theories of ore genesis, and a relentless discontent with the accepted geology of the Summitville area. To set the stage for this discovery period, it must be noted that it began 100 years after gold was first found at Summitville. It was the height of the "porphyry copper" era and gold was still not a part of the explorationists&apos; portfolio. It was also a time of great intellectual stimulation. Theories were rapidly developing to relate different types of ore deposition and to place ore genesis within the fabric of plate tectonics. Summitville itself had just been linked to the newly discovered Platoro caldera complex and the Platoro lineament. This in turn related Summitville to the other San Juan volcanic field caldera ore deposits.

Jan 1, 1990

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By John B. Goddard

The discovery of rhenium on the ion exchange resin used at the uranium in-situ leach operations at Palangana (Texas) led to a laboratory study on the possible methods of recovery. Rhenium, present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, Re04-, concentrated on the anion exchange resin, which was a factor of ten more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the perchlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3[N] or stronger concentration of nitrate containing up to 0.5[N] H+ was found to be the system of choice. A rhenium sulfide concentrate containing up to 14% Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4Re04 followed by hydrogen reduction at elevated temperature.

Jan 1, 1982

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998