Search Documents

By M. T. Long

The Crestmore Limestone Mine of Riverside Cement Company in Riverside, California is situated within 1.6 km of the Santa Ana River. It is an alluvium covered deposit with a massive quartz manzonite intrustion separating the upper and lower limestone beds which dip from 30° to 50°. The highly fractured upper bed contacting the Santa Ana alluvium contains many unique water inflow problems which vary, from multiple high pressure 19 liters per minute inflows up to 3,000 liters per minute to 11,000 liters per minute inflows-contacted by development mining in April 1983. A case history of the successful grouting of these inflows and the continual grouting procedures in advance of present mining with empirical' results are discussed.

Jan 1, 1984

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By P. W. Finck

Detailed mapping, using a large diameter diamond-drill in conjunction with high resolution reflection seismics, has increased known resources of kaolin clay and glass-grade silica sand from scattered deposits generally < 1 km2 to large areas of Cretaceous valley fill up to 130 m thick. Detailed chemical and physical analysis of drill core is presently underway. Silica sand deposits intersected in this study are up to 99.4 % SiO2 without beneficiation. Light grey to white kaolin clays identified by XRD and DT A have concentrations values (without beneficiation) up to 47.28% SiO2, 37.44% Al2O3, 0.45% Fe2O3, 0.49% K2O, 0.07% Nap, 0.07% CaO and 0.39% MgO.

Jan 1, 1996

By I. K. Choi

In a recent paper by Smith and Wen(1) the adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite was studied. As would be expected considering the general negative character of kaolinite, except perhaps at quite&apos; acid pH values (2,3,4), it was found that trimethyldodecylammonium chloride adsorbed strongly on kaolinite at basic pH values. Furthermore, it was found that sodium dodecylsulfate adsorbed strongly on kaolinite at acid pH values, particularly at initial 1H values below pH 3 (final pH values near pH 4). It is interesting to note that adsorption of the anionic surfactant was strong under conditions where the kaolinite was apparently slightly negatively charged (2). The present paper reports on an extension of the work by Smith and Wen. In this paper the effects of the presence of dodecyl alcohol and sodium hexametaphosphate on adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite are considered.

Jan 1, 1967

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

An AFM has been applied to study in situ the adsorption of oleic acid on fluorite in aqueous solutions. The AFM images show that fluorite surface becomes smoother with the adsorption of 7 × 10-5 M oleic acid solution at pH 9. Force measurement shows that fluorite is strongly positively charged in water at pH 6, suggesting a neglectable surface carbonation of fluorite. The adsorption of oleic acid at pH 9 renders fluorite more and more negatively charged. The surface morphology change of fluorite as shown by the AFM images suggests that oleic acid chemisorbs on fluorite at pH 9. Increasing temperature can help increase the adsorption of oleic acid on fluorite. It may also improve the lateral polymerization of unsaturated oleic acid on fluorite as suggested by the smoother mineral surface in oleic acid solutions at an elevated temperature.

Feb 23, 2014

By P. Massacci

The modelling of phenomena by nonlinear dynamic Systems Theory representations require the specification and identification of suitable models of the phenomenon and the availability of good optimization algorithms to determine the optimal controls. Stochastic disturbances and difficulties of monitoring the process lead invariably, otherwise, to suboptimal performance. It will be shown that an algorithm can be formulated which will simultaneously identify and optimize such a system. The properties of the algorithm will be derived and its convergence to an optimal control proved. Some results of actual applications will be presented and it will be shown how this approach generalizes easily to optimal control of the actual processing system. These results generalize those of optimal learning and input conditioning.

Jan 1, 1991

By B. E. Davis

A technique was devised by the Bureau of Nines to recover coarse (plus 1.7 m) North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17.0-pct-P205 reject to 24.5 pct P205 with a phosphate recovery of 63 pct.

Jan 1, 1985

By John A. Wolfe

Applications of mathematical statistics to the field of exploration are still relatively new. There are two primary reasons why little has been published in this field. First, if one discovers an effective technique for exploration, he does not like to disclose it. Second, the geologist needs to work closely with a mathematical statistician, and the communications barrier between the disciplines is formidable. The authors of this paper, one a geologist and the other a statistician, were interested in the economic benefit which appeared to be possible in the interdisciplinary area which they have called "geostatistics." An actual example has been selected to illustrate this benefit.

Jan 1, 1962

By Edward K. E. ] [Williams

Conditioning is any treatment of an ore with or without reagents which affect its floatability. While it can start in crushing or grinding circuits and continue into the flotation circuit, conditioning will refer here only to reagent treatment in an agitated tank designed for the purpose. Such treatment is often unnecessary with sulphide ores and collectors or with amines,* but it has long been recognized as essential with fatty acid collectors in the flotation of non-sulphide minerals, The requirements can be extremely variable, depending upon ore alteration, the presence or absence of slimes, and 1 the minerals to be separated. The study described here was concerned with the recovery of oxidized molybdenum minerals from an ore containing the element in both sulphide and oxidized form. Flotation of the iron minerals with which the oxidized molybdenum was associated was the basis for the process. Recovery and optimum concentrate grade without desliming depended upon a twenty to thirty minute conditioning of the pulp with flotation reagents at forty to fifty percent solids and at high turbulence. The objective in the study was the determination of design and operating criteria for conditioners in order to permit scaling-up of the results without repeating the entire study on a larger scale.

Jan 1, 1968

By U. Cetin

The Nevada Test Site is located approximately 65 miles northwest of Las Vegas, NY. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, volatile and non-volatile organics, and explosive materials. Leaching and transportation of these contaminants are creating severe environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement of the existing impermeable barriers (clays). In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper will present the results of the sorption tests for the target radionuclides.

Jan 1, 1998

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By C. C. Harvey

Based on resource studies in many developing countries, four categories of industrial clay resources are recognized as precursors to development strategies. Category I: High quality, high technology clays requiring major investment for large tonnage international markets. Category 2: Unique specialty clays requiring advanced technologies for small tonnage niche markets. Category 3: Lower technology, moderate quality clays, predominantly to supply local markets. Category 4: Low quality clays requiring little or no processing. Projects with Categories 1 and 2 clays require extended development times (green field to investment decisions) with significant pre-development investment, while projects with Categories 3 and 4 clays require shorter development timetables and lower levels of investment.

Jan 1, 1998

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By V. L. Brant

The estimated total energy demand for the U. S. is 60 quadrillion BTU for 1970 and is expected to more than double by the year 2000. Today the energy crunch is here. It is evidenced by brownouts to conserve electrical energy, and the shortage of gas and oil. Many such headlines, including suggestions for energy rationing, are in the news today. Paradoxically we have an abun¬dant source of energy in the form of coal. Energy consumers, however, are geared to use fuel in other forms. It is the intent of this presentation to discuss processes under development for conversion of the energy contained in these vast coal reserves to more usable forms. Coal conversion to synthetic fuels should be of particular interest to those engaged in mining. Coal consumption in a single conversion plant is expected to range from 10,000 to 40,000 tons per day. Plants will be located at the mine mouth and will operate continuously 24 hours per day, seven days per week. Further, many such plants will be needed., For example, looking at natural gas only, the supply/demand gap is estimated to reach 13 trillion cubic feet per year by 1985. Assuming that gas from coal conversion were to fill only 101, of this gap, 15 plants producing 250 MMSCFD would be required. These plants would consume about 90 million T/Y of coal or 135 million T/Y of lignite. It will indeed be a challenge to mine, suitably prepare, and transport coal at these projected volumes without interruption. Many ideas have been conceived for better utilization of coal and these are in various stages of development. Those supported by public money are covered by the Annual Report of the Office of Coal Research (OCR), Department of Interior. The two processes to be discussed, the Consolidation Coal Company&apos;s (Consol) C02 Acceptor Process (1)(2)(3) and The Pittsburg and Midway Coal Mining Company&apos;s (PAMCO) Solvent Refined Coal Process (4)(5) are both sponsored by OCR.

Jan 1, 1970

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By Keros Cartwright

Distribution of temperature within the lithosphere can be significantly affected by the movement of ground water. Stallman (1960) presented the basic equation for the simultaneous transfer of heat and fluid in a porous medium and first used earth temperatures to determine aquifer permeability. Subsequently, studies of rock and soil temperatures were used to determine the flow of water through clay layers separating aquifers (Bredehoeft and Papadopulos, 1965; and Sorey, 1971), and to locate shallow aquifers (Cartwright, 1968; Birman, 1969). Cartwright (1968) showed that shallow aquifers maintain a nearly constant temperature throughout the year and that heat is exchanged between the aquifer and land surface. These temperature data also suggest that shallow aquifers hydrologically connected to surface-water systems have significantly greater effect on temperature distribution than aquifers in the deep artesian basins. Water wells developed in the shallow glacial and dolomite aquifers to depths of over 122 meters (400 feet) in northern and central Illinois produce water at temperatures very close to the mean annual air temperature. An analysis of the character of the rocks and soils suggests that the tem¬perature gradient should, and does, vary according to changes in thermal conductivity due to changes in lithology. This is because, under conditions of steady and uniform flow of heat from the earth&apos;s interior to the surface, a greater temperature gradient is required in poorly conductive rocks than in highly conductive rocks to transmit the same quantity of heat. Based on estimated values of thermal conduc-

Jan 1, 1972

By T. D. MacQueen

Thank you Mr. Stevens. It&apos;s a pleasure for me to be speaking to this meeting of the Society of Mining Engineers of AIME this afternoon, and the Gypsum, Association is grateful for the invitation. A brief word about who we are: the Gypsum Association is the trade association for the gypsum industry - the manufacturers of gypsum board and lath a-d plaster. We have a membership of eight companies. These eight companies produce about 90% of the gypsum products manufactured in the United States ... closer to 94% actually. Our headquarters is in Evanston, Illinois. We have an east coast office in Washington, D.C. where the eastern manager handles technical and building code matters and maintains liaison between all of the government agencies and departments and our industry. We also have a west coast office in Los Angeles where our west coast representatives is heavily involved with the Uniform Building Code and ICBO. And then in the Evanston office our manager of technical and building code services, Herb Carlsen, bites his nails and loses his hair over these problems and various other projects that come in, such as conversion to metric and various other things. We also have a research associate at the National Bureau of Standards in Washington who is currently concentrating his efforts on the combustibility of building materials. His studies involve current testing methods, definitions, data analysis, and proposed new testing methods,.&apos; It is anticipated that this program will lead to a better understanding of non-combustibility of building materials and systems. I mentioned that our members represent over 90% of gypsum products,&apos; manufactured in the United States; it might be well to point out a couple of statistics about what that really means. According to the Bureau of Mines,

Jan 1, 1977

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the&apos; variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993