Search Documents

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By H. G. Papacek

The Fabrica Mine of the Brazilian iron ore company Ferteco mines on an extremely inhomogenous ore deposit. A large amount of the crude ore consists of fines minus 100 micron which cannot be sold without further treatment because of its chemical and physical properties. In order to make full use of the mined crude ore an expansion program has been realized which incorporates among others a concentrator to produce classified blast furnace ore , sinter feed and pellet feed. The pellet feed is converted in a 2.5 million tons per year Lurgi Dravo plant into high grade pellets. The paper discusses the selection of the concentration process, the pelletizing process and describes the experiences with the operation plant during the startup and the first years of operation.

Jan 1, 1979

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By Martin Knights

The UK Industry is preparing a new guide on Tunnel Asset Management that reflects current industry advances, in developed technological innovation and evolving tunnel asset owner requirements. This will enable asset owners to have a trusted practical guide that can support technical and commercial decisionmaking regarding tunnel assets and aging infrastructure. It will also provide updated guidance for a spectrum of stakeholders including: • Consultants. • Contractors. • Planners, insurers. • Academia. • Government. Industry views will be crucial in the preparation of the Guide that will assist proactive & predictive planning and maintenance regimes and the availability of the asset. The Guide will enable changes in current working practices, share updated recommendations and provide a route map to implement future requirements for tunnel asset management. The generic content of the Guide would be applicable to North American practice.

Dec 1, 2022

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By Stanley V. Lachmansingh

Bauxite can be regarded as a mixture of hydrated aluminium oxides the predominant constituent - and oxides of iron and titanium, silica and silicates. Heterogeneous and non-crystaline, most bauxites vary in average composition from one deposit to another both in terns of impurities as well as the proportion of Gibbsita and the Monohydrates Diaspore and Boehmite. Iron levels (as Fe2O3) can vary from less than 1% to as high as 30% with the alumina content ranging from 40 to 6o%,. Gore than 90% of all bauxite mined in Guyana is used as feed for the - production of refractory grade calcined bauxite. There are -however, several speciality grades used in various industrial applications and these are characterised by the quality of the bauxite in particular ;,with regards to iron and silica levels which generally have to be low. The main speciality grades are designated Refractory, Abrasive and Chemical. Bauxitte is also used in the production of nigh alumina cements,, activated bauxite end in the manufacture of electrical insulators.

Jan 1, 1977

By Randall J. Weege

Nickel laterites throughout the world are similar in their gross aspects, but vary significantly in detail. The deposits occur in two separate and distinct geologic settings --those formed over ultramafic rocks which were mechanically emplaced, and those formed over ultramafic rocks that were intruded as melts. The source of the primary nickel in the parent rock may occur both as ionic replacement in silicate lattices and as nickel sulfides. Factors controlling the degree of laterization and nickel enrichment are dependent upon the parent rock characteristics as well as chemical and climatic conditions. Two chemically and physically distinct zones (oxide and saprolite) are commonly present in the laterized rock, but one or the other may be extremely thin or absent. Cobalt and copper may be present in recoverable amounts. Geologic, geophysical and geochemical methods are all utilized in exploring for these deposits. These methods are compared, evaluated and illustrated in the paper. Drilling patterns and ore reserve calculations are also discussed. In contrast to many ore deposits, processing costs are much higher than mining costs. The most efficient processing method is directly dependent upon the chemical composition of the ore. This variation in the chemical and physical characteristics of nickel laterites requires a detailed test program of the metallurgical response to representative samples and blends of ore. Detailed laboratory and bench-scale metallurgical tests are necessary prior to a full scale pilot plant test.

Jan 1, 1978

By M. Kaya

This paper presents an experimental method to determine the degree of gangue entrainment in mechanical flotation cells and proposes new and inexpensive methods to lessen it. The applicability of froth washing and vibration was studied in laboratory, pilot plant, and plant scales. The effect of wash water on metallurgical performance was tested with various streams from the Falconbridge Strathcona mill at laboratory, pilot, and plant scales, with the 2nd cleaner at the Eastmaque Kirkland Lake mill, and with the 2nd and 3rd zinc and 3rd and 4th copper cleaners at Les Mines Selbaie mill. It was found that gangue recovery was closely related to water recovery in all systems. Wash water at an optimum superficial rate from 0.03 to 0.07 cm/s reduced entrainment by anywhere from 30X to 70X. Wash water can be further assisted by mechanical and ultrasonic vibration of the froth. A further rejection of 10 to 20X becomes possible. As a result of this work, a number of plants in Canada and in the United States have evaluated and/or are now using froth washing.

Jan 1, 1990

By Robert F. Conley

Attrition milling, once employed exclusively for the dispersion of pigments, has in recent years found a host of new applications in the area of mineral processing and mineral-pigment production. Broadly categorized, attrition milling is divided into two classes, as defined by the machinery's function, vibratory milling and rotational milling. Each mill type has been defined as a variation on ball milling and the terms, "vibratory ball mill" and stirred ball mill" appear in the literature. The primary design differences between attrition and ball mills are: (1) a stationary canister (or shell) (2) smaller grinding media (3) grinder energy is motor limited rather than gravity limited (4) strong media/feed size dependance.

Jan 1, 1983

By Howard E. Kremers

Although more than 100 thorium-rare earth minerals are known, only a few have any commercial significance. Monazite, thorite, bastnasite, and some exotic thorium rare earth ores are reviewed Commercial interest is presently centered on monazite from the Union of South Africa, and thorite from this country. Thorium became commercially important with the development of the incandescent gas mantle about 75 years ago, Gas mantles consist of thorium oxide with small amounts of cerium oxide. The thorium nitrate used to make gas mantles was first obtained from rare thorium minerals, As a matter of fact, this use of thorium is still important and is one of the largest commercial uses for thorium materials. The discovery of monazite sand placer deposits along the coasts of Travancore, India, and in some Brazilian beach s .s, and the development of the old North and South Carolina monazite stream placers gave the mantle industry of 30 to 40 years ago a comfortable inventory of thorium ore. Even today, the thorium industry depends largely upon monazite ores for its source of thorium. This paper will briefly describe some of the major thorium ores and their principal deposits insofar as they relate to the thorium industry in this country. Because of similar chemical and physical properties, thorium always occurs with the rare earth elements and with varying amounts of yttrium. Thorium may predominate over rare earths, as in thorite-type minerals, or may represent only a fraction of the rare earth content. Typical ratios of thorium to rare earths in various minerals are given in Table 1, The average thorium content of the earth's crust is about 12 grams per ton, and in this respect thorium approximates lead, molybdenum, and some of the rare earths in abundance. The ore minerals of greatest importance to the-thorium-rare earth industry are monazite, thorite-type minerals, bastnasite-type- ores, and the family of minerals which is characterized by a preponderance of the heavy rare earths and yttrium. The latter classification includes xenotime, gadolinite, samarskite, euxenite, etc, The first two, monazite and thorite, are of greatest significance.

Jan 1, 1958

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Qingqing Huang, Mohammad Rezaee

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 12th MPD Student Poster Contest on March 2, 2022, during the MINEXCHANGE 2022 SME Annual Conference & Expo. The event showcased the work of 32 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to explain their research to a panel of judges during the conference. Recognizing the students’ efforts in working hard on their research topics and setting aside time to complete the necessary steps to enter the poster contest, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 22, 2022

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By N. Arbiter

Fracture under low velocity free-fall and double impact, and under slow compression have been-investigated. The pattern of breakage and the size distribution of resulting fragments for sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of principal compression as determined by mathematical analysis Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments.

Jan 1, 1968