Search Documents

By Phil Shelton

What exactly does clean coal mean? Mining coal creates dust and releases methane gas. And burning coal liberates CO2 and emits particulates, including SO2 and NOx. Coal creates wastes that are often stored in unsightly and potentially dangerous slag heaps and lagoons. When clean coal technology is discussed, it sometimes seems that creating modern or ?ultra super critical? coal-fired power stations is presented as the main or even the only answer. However, there may be a more holistic approach. Using the energy potential of coal is always going to have environmental impacts. Some of these will be negative. But the need to secure future energy resources demands that society tackle these negative issues and find ways to minimize and offset them.

Jan 1, 2010

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By S. Goodfellow, J. C. Ordóñez-Calderón, K. Esmaeili, N. Houshmand

A good understanding of the hardness of ore being handled and processed in a mining operation can significantly improve operational efficiencies by providing valuable data to support decision-making through the mining value chain (drilling, blasting, comminution). This study presents the results from the application of Machine Learning (ML) to predict rock hardness using various geophysical and geochemical features. Core samples from a mine site were logged using a multi-sensor core logging system. Measurements including ultrasonic p-wave and s-wave velocity, elemental concentration via portable XRF, and Leeb Hardness, were measured every 2 cm along the length of the core. The ML model was set up to predict the Leeb Hardness using the elemental concentrations and ultrasonic velocities as predictors. The Leeb Hardness values were grouped into three bins and used as a classification target for the ML models. Various ML models, including linear regression, support vector machines, decision tree, XGBoost, Random Forest, K-Nearest Neighbors, and Naïve Bayes were tested. The model performance demonstrated that the Random Forest and XGBoost models produced the highest accuracy of 74-91%. Random forest and XGBoost were then selected to perform regression models to estimate a Leeb hardness value rather than a hardness class. These models were able to estimate the Leeb hardness value by 4.57-4.87 % error.

Mar 2, 2022

By R. L. Weigel

As Florida phosphate mining gradually moves from the Bone Valley formation to the Hawthorn formation, a greater portion of the minable deposit contains dolomitic diluents which result in lower product grades that can be detrimental to the production of phosphoric acid for fertilizer uses. One beneficiation technique found applicable to the phosphate pebble size range (3 X 16 mesh) is heavy media separation using suspensions of magnetite and ferrosilicon. As part of an ongoing investigation of dolomite removal technology, a pilot heavy media cyclone system was constructed by IMC and used in the testing of a variety of drill core composites and hulk samples. The results of these tests were used to develop a predictive model for heavy media cyclone separation based on pebble fraction assays and heavy media operating parameters. This model is currently being used in the evaluation of specific future mining areas.

Jan 1, 1984

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By Liming Yuan, Wei Tang, RICHARD THOMAS, DAVOOD BAHRAMI

The location and orientation of fire suppression nozzles is critical in suppressing mobile mine equipment fires. To effectively suppress such fires, optimization needs to be considered for the suppression nozzle locations and discharge angle. Detailed experiments were conducted to study the effectiveness of fire suppression agents with different nozzle configurations. A variety of fire suppression systems including dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist were used. Six types of nozzle locations were studied, and their fire suppression effectiveness were compared. Results from this work highlight potential considerations when determining effective fire suppression designs.

Feb 1, 2025

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020

By Spencer R. Titley

Porphyry copper deposits in the southwestern Pacific area represent relative newcomers to the growing number of occurrences of this mineral deposit type. In addition to firmly establishing the importance of this region and its potential influence within the framework of world copper resources, the deposits of this region are significant from a scientific point of view because of their close relationship to the phenomena of Island Arc evolution. Since the discovery of Panguna on Bougainville in 1964, the list of prospects, proven and unproven, and developments, has grown to more than twenty and the number continues to increase. At the time of this writing, the number of prospects is imperfectly known but the following localities and numbers are fair minimum approximations: Manus (Admiralty Islands) (3); New Britain (5); New Ireland (1); Guadalcanal (2); New Guinea Highlands (6); Misima (1); and Fiji (2); Proven prospects are present in the new Guinea Highlands (2); one deposit is being developed in Test Irian, and one orebody, on Bougainville, is in production. This summary paper concerns a discussion of some of the geological characteristics of producers, developments, and prospects on the Islands of Nets Guinea, New Britain, Bougainville, Guadalcanal, and Manus. I am not aware of publishable data for Misima or Fiji. As so many variables ultimately determine whether or not a porphyry copper occurrence becomes an orebody, not the least of which is geography, this summary treats the characteristics of these occurrences which alloy; their assignment to the porphyry copper category. For purposes of this discussion, I have considered those copper occurrences which are apparently genetically related to talc-alkaline intrusions and in which the content of copper has been upgraded 50 to 100 times the Clarke for that particular host rock. Some of these occurrences are shown on Figure 1.

Jan 1, 1973

By Jeffrey Peterson, John Beesley, Martino Scialpi, John Cassidy

The DC Clean Rivers Project is DC Water's ongoing program to capture and treat combined sewer overflows (CSOs) during rainfall before they reach the District waterways. The Anacostia River system was designed to reduce CSOs into the Anacostia River and includes the Blue Plains Tunnel, Anacostia River Tunnel, First Street Tunnel, and Northeast Boundary Tunnel. A portion of the Anacostia River system was commissioned in March 2018 and the final component, the Northeast Boundary Tunnel, was placed in operation on September 15, 2023. This paper provides a summary of the experience gained during construction of this +$2.9 billion project, an overview of the system performance since its activation in 2018, and a look-ahead to the next phase of the DC Clean Rivers program: the Potomac River Tunnel.

Jun 23, 2024

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

This study presents the application of low-cost dust monitors (LCDMs) for real-time monitoring of respirable dust in a mining environment. LCDMs significantly enhance data collection by providing continuous, granular and cost-effective dust concentration readings. This case study demonstrates that by deploying LCDMs, mining operators can respond quickly to changes in dust levels, improving occupational safety and air quality management. The results show how such monitoring technologies can be integrated into routine operations to reduce dust exposure and prevent health hazards such as silicosis, especially when coupled with appropriate mitigation strategies.

Nov 1, 2024

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By Jr. Smith

Silver-gold ratios were studied at the Tayoltita epithermal vein deposit using channel sample, channel sample line, stope, ore body and vein sample populations. The ratios are highly variable among individual channel samples (25:1 to greater than 500:1) with both high and low values randomly distributed within ore bodies and veins. Whole vein ratios for the fourteen most important ore producing structures range from 44:1 to 105:1, and show zonal distribution relative to two small granitic stocks, low values closest to the intrusives. The zoned nature of the deposit suggests that the stocks, apophyses of an underlying batholith of Late Eocene age, were the heat engines which powered the hydrothermal system responsible for ore deposition.

Jan 1, 1978

By Neilson Rudd

Many deep well waste disposal. operations have adopted the technology of the petroleum industry but fail to make full use of the knowledge and experience upon which this technology is based. Inexperience in subsurface exploration commonly leads industrial personnel to an over simplified understanding of the complex subsurface rock/fluid environment and overly optimistic "degree of exploration /adequacy of knowledge" ratios. Several fundamental differences between disposal and petroleum production are discussed. In particular, the evolution of understanding of the subsurface in relation to degree of exploration is demonstrated by summarized case histories of such other forms of subsurface fluid exploitation as oil pro¬duction and underground gas storage, tracing subsurface interpretations from the initial exploratory concept to that of fullest development. Evolutionary changes in interpretation and their significance as applied to deep well disposal are stressed.

Jan 1, 1971