Search Documents

By D. Kruse

Top-down constructed large-diameter (up to 90 m or 300 ft) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to analyze various failure modes, evaluate the shaft liner and internal structures' response to seismic loading, assist in segment design and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored. Mining Engineering, 2011, Vol. 63, No. 9, pp. 81-88. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

The North Singhbhum Mobile Belt (NSMB) lies between two crustal-scale shear zones, the South Purulia Shear Zone (SPSZ) at the north, and the Singhbhum Shear Zone (SSZ) at the south. The Babaikundi-Birgaon Axis (BBA) is an east-west trending secondary shear zone in the NSMB lying south of SPSZ, which is known for the occurrence of gold along with other sulfide minerals within the quartz reefs. The present study has been carried out at north of Ichadih village, which lies on the BBA. The present study attempts combined electrical resistivity tomography (ERT) and self-potential methods along a profile of 470-m length in the Ichadih area to map the potential mineralized zones. Initially, ERT sections generated by Wenner, Wenner- Schlumberger, dipole-dipole, and joint inversion of the combined array have been analyzed, and results are validated through the analysis of model resolution. A prominent low resistivity (10–100 Ωm) associated with quartz reef/limonitic quartz reef at a depth of approximately 30–85 m, encircled by a high resistive (more than 10,000 Ωm) formation associated with metasedimentary rock, has been delineated using joint inversion of the combined array. Further, analysis of self-potential (SP) anomaly using particle swarm optimization inversion also confirms the prominent low SP anomaly at a depth of 77.3 m, which is analogous to the low resistivity anomaly identified in the joint inversion of the combined geo-electric array. Subsequent analysis of a complex synthetic geo-electrical model analogous to the present field situation proves the efficacy of the joint inversion of combined arrays. As a whole, joint inversion of multi-array data is established as an efficient technique for better subsurface imaging in case of the complex subsurface structure. In-depth analyses confirm the possibility of sulfide mineral-rich deposit (quartz reef/limonitic quartz reef) which requires further geological drilling and lithogeochemical sample analysis, for possible future exploration.

Oct 26, 2020

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By S. K. Palm

The commercial life of a mineral product can be long, but like hitech electronic and software products that soar in sales one day to become obsolete and forgotten a few months or years, mineral products have a life cycle. They are invented, commercialized and eventually decline and disappear from commerce. Diatomite and perlite are produced from mined minerals, but almost none of the products in these industries spring from the earth in finished form. Straight calcined diatomite was invented over 100 years ago and flux calcined diatomite just a few years later. The expansion properties of perlite were discovered and first exploited about 75 years ago. Some applications for diatomite have disappeared or currently face competition from newer products. Dry cleaning was once the second-largest application for diatomite but disappeared over 30 years ago. Both the beer and wine filtration markets for diatomite face increased competition from membrane filters. A pipeline of new, proprietary products is critical to the future of the industry.

Mar 2, 2022

Well designed and maintained haul roads are the key to minimizing truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often difficult to achieve. Poorly designed and built roads exhibit high rolling resistance - a 1% increase in road rolling resistance can typically reduce speed on ramp by as much as 10% - and on the flat by up to 26%. In the current economic climate, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations ? simply by virtue of their contribution to overall cost of operations ? often in excess of 50% of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled ? is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road design is developed, and, critically, the interplay between a good design and safe, cost efficient haulage. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers? requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimize haulage hazards, both from a health and safety perspective. Whilst improved mine haul road design does indeed reduce haulage accidents, recognition also needs to be given to human factors which are a significant contributor to haulage accidents. The human factor is the most problematic to address in a road design. It is often easier break the link between the interactive effects which may lead to accidents than trying to predict and reduce human error. These human factor interactive effects include the geometric, structural and functional design components and to prevent an accident or reduce the severity of its consequences, a road should be more accommodating to human error. The more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By A. D. Hammond

Vanadium is a transition metal, ductile and silver-gray. It is harder than most metals and steels and it has a good resistance to corrosion. It is stable against alkalis and sulfuric and hydrochloric acids. Vanadium is oxidized in air at about 660° C (1,220° F), although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states, 2-5. In aqueous solution, the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called roscoelite K(V3+,Al,Mg)[(Si,Al)4O10] (OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world?s vanadium mine production comes from magnetite-hosted deposits and, to a lesser extent, sedimentary-hosted sandstone.

Dec 1, 2013

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By E. Watkins, S. J. Schatzel, V. Gangrade, R. Kimutis, J. Addis, C. Hollerich

The recent shale gas revolution in the United States has led to the drilling of hundreds of unconventional shale gas wells in active and future coal reserves in traditional coal-mining regions of Pennsylvania, West Virginia, and Ohio. This paper summarizes the impact of a shale gas well breach on the mine ventilation system of an operating longwall panel. This study utilizes a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) to simulate a single-panel longwall operation. The LIAM will be utilized to identify flow pathways and distribution patterns of gas from breached gas well scenarios in an operating longwall in the Pittsburgh Coal Seam. Sulfur hexafluoride (SF6) tracer gas is utilized to simulate a breached gas well. Preliminary findings suggest that the breached gas is diluted to regulatory levels and does not accumulate in the mine entries or in the longwall gob when the longwall panel is adequately ventilated. Overall, this study characterizes the potential interaction between shale gas wells and the mine environment in the event of a gas well breach, which provides critical information to the industry and regulatory agencies for improving safety, health, and welfare of miners.

Mar 2, 2022

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020