Search Documents

By Luther W. Hyde

Ground water, one of Florida's most valuable resources, is also one of its most abundant. The State is fortunate to have several prolific ground- water reservoirs that yield tremendous quantities of water to wells and to some of the world's largest springs. These ground-water reservoirs, or aquifers are of two types artesian and nonarteaian. Ad artesian aquifer is one that contains water under sufficient pressure to rise above the top of the oontaining formation. A nonartesian aquifer is one that contains water which is not confined, and the upper water surface (water table) is free to rise and fall. The principal source of ground water in Florida is the artesian Floridan aquifer which supplies most of the water users in the State. Nonartesian sources include the Biscayne aquifer of southeastern Florida, the sand-and-gravel aquifer of extreme western Florida, and a shallow aquifer which lies at depths of less than 100 feet over much of the State. The accompanying map shows the approximate areas where these aquifers are the main source of supply; however, the boundaries do not represent the areal extents of the aquifers. For example, the Floridan aquifer extends beyond the southern boundary shown on the map, but it is not of great economic significance there because the water is highly mineralized. Aquifers other than the four described occur in the State, but they are, for the most part, of minor significance. One of these is an artesian aquifer which is formed by permeable zones that occur locally within the confining beds above the Floridan aquifer.

Jan 1, 1966

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By John A. Reeves

The Coal Creek Preparation Plant is the coal cleaning facility of Mid-Continent Coal and Coke Company. Located three miles west of Redstone, Colorado, and at an elevation of 8,040 feet the preparation plant cleans coal produced at the company's Dutch Creek Mine and L. S. Wood Mine. (See Fig.1.) Current production is at the rate of 2500 tons per day clean coal. Plant capacity is rated 350 TPH raw coal. Reject rates vary with mining conditions from 8% to 25%. Factors which influenced the design of the coal cleaning facility were the characteristics of the coal, the location in a tourist oriented resort area, and the extreme winters of the area. Lack of areas suitable for settling ponds and the necessity of keeping effluent waters out of the fishing streams dictated a closed circuit plant. Severe winter conditions, which last six to seven months out of the year and temperatures which have dropped to 40° F. below zero on occasions demanded that the plant be totally insulated and enclosed indoors.

Jan 1, 1967

By Paul H. Johnson

A new system for leaching many types of ores has recently been developed on a commercial basis by J and J Research and Development, Inc. of Hanover, New Mexico. This revolutionary new leaching system consists principally of three new leaching reactors; viz, (1) a large, air-agitates, column-like reactor for leaching crushed ores that is constructed in an underground environment and has the inherent ability to do a very efficient job of leaching, (2) a vat-like, air-agitated vessel for leaching an rinsing finely ground ores and , (3) an air-agitated copper precipitation column that is built underground and utilizes an inexpensive dense or heavy scrap iron as a copper precipitant. Each of these new reactors have been used in a large leaching plant near Hanover, New Mexico.

Jan 1, 1973

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By J. H. Hammarstrom, S. M. Fortier, W. C. Day, S. J. Ryker, R. R. Seal

"The United States’ supply of critical minerals has been a concern and a source of potential strategic vulnerabilities for U.S. economic and national security interests for decades (for example, see Strategic and Critical Minerals Stockpiling Act, 1939). More recently, with the rapid increase in the types of materials being used in advanced technologies (Fortier et al. 2018a), and geopolitical events surrounding the supply of rare earth elements (Ting and Seaman, 2013), among other developments, the critical minerals issue has again achieved a high level of visibility within the U.S. government (Executive Order 13817 (2017)).In this paper, the U.S. Geological Survey (USGS) provides an overview of its ongoing focus on critical minerals through the agency’s core competencies in mineral information, mineral resource assessments, geologic and topographic mapping, geophysical surveys and mineral resource research. Aspects of the multifaceted critical minerals issue addressed here include:• Identifying minerals that meet the definition of “critical” provided in Executive Order 13817.• U.S. net import reliance for critical mineral raw materials.• Current status of domestic critical mineral resource assessments.• Current status of topographic and geologic mapping, and geophysical survey coverage of the United States.• The Earth Mapping Resources Initiative (Earth MRI) to support future critical mineral exploration.• Critical mineral potential of waste streams from extractive industries.Identifying minerals as criticalU.S. government agencies and other organizations use a number of existing definitions and criteria to identify a mineral or mineral material as critical, strategic or otherwise important. The executive order defined a “critical mineral” to be “(i) a nonfuel mineral or mineral material essential to the economic and national security of the United States, (ii) the supply chain of which is vulnerable to disruption, and (iii) that serves an essential function in the manufacturing of a product, the absence of which would have significant consequences for our economy and national security.” This definition is broadly consistent with that defined by the National Research Council (NRC, 2008) and may be summarized as “essential in use” and “subject to disruption of supply.” Virtually all of the dozens of critical minerals studies conducted since the 2008 NRC report have used some variation of this same definition (Hayes and McCullough, 2018)."

May 1, 2019

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972