Search Documents

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By Dhananjaya Senapati, E. V. S. Uma Maheswar, C. R. Ray

Carbothermic process of Ferro Silicon production is primarily a slag-less process. However, slag formation is observed in the regular operation as experienced by almost all the Ferro Silicon Producers in different pro-portions. The problem of slagging in the furnaces may be due to: a)Variation in the input burden charge material quality b)Fluctuations in the Carbon balance and/or c)Fluctuations in the Electrode penetrations The problem will be more severe in nature with the increase of the size of the furnace. The operation performance of the furnace gets badly affected if the slag formed in the furnace is not removed from the bath in time and to the maximum extent possible. It is, therefore, very essential to know the characteristics of the slag formed in the Ferro Silicon Furnaces, besides eliminating the very cause of formation itself; and to find the routes of draining of the same from the furnace bath effectively. This paper envisages the effects of using the LIME STONE in the Ferro Silicon Burden in stabilizing the 48MVA Furnace for improved performance and better consistency. Quality fluctuations in the available Raw Materials are compared with that of the requirements for the Ferro Silicon production. The furnace operational data is compared for 12 months period each for the period corresponding to the before and after usage of lime stone in the burden and found encouraging results in the performance. Implications of use of Lime Stone in the burden on the quality of the output alloy are also studied.

Jan 1, 2007

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By J. Kuijpers

Failure and fracturing are often regarded as synonymous. While this is obviously true in an environment dominated by tensile stresses, it is still not clear how failure and macro fracturing are related in a compressive stress environment. Excavations at great depths are typically subjected to compressive stresses only. The fracturing observed around such excavations is therefore commonly assumed to be induced by such compressive stresses. The physics of such a phenomenon have unfortunately never been explained properly, so that the formation of these so-called extension fractures still remains a mystery. As the presence of fractures is an important factor affecting the stability of underground excavations, it is of practical relevance to understand their formation. In this paper, a possible explanation is proposed. It is argued that fracturing in a compressive stress environment is a secondary effect. Primary failure, in the form of micro fracturing and associated damage is assumed to precede the major fracture processes. The fractures are thus generated in response to material failure and may not directly be the cause of failure. The implications for material response and behaviour are discussed. Keywords: micro fracturing, macro fracturing, extension fractures, failure, compressive stresses, damage, excavations.

Jan 1, 2000

Paper written on project work carried out in partial fulfilment of BSc Engineering (Mining) The aim of this project is to determine whether certain pillars occurring within the no. 1 shaft and no. 2 sub-shaft ground are feasible for extraction. The extraction of these pillars is essential in prolonging the life of Kloof Main Shaft as its VCR resource becomes depleted. Extraction of these pillars will require a combination of designs and factors, with rock mechanics and ventilation being the main considerations. Primarily for the pillar extraction, an initial production target of150 kg gold, mine able in one year from commencement of ?opening up? was set. The planned target has been exceeded and the feasible pillars identified are expected to yield an additional 1 390 kg of gold to the shaft?s production profile. However, not all the required ventilation designs have been completed to date, the reason being that at the time of the project, many of the pillar areas were inaccessible and thus ventilation conditions are unknown. This project is therefore an ongoing process and will require further design once all targeted pillar areas have been opened up. A preliminary costing analysis of the pillar mining was performed and it was found that all targeted pillars with the exception of 38?61 pillar are profitable.

Jan 1, 2005

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By H. Thomas, I. N. M. Nday

"*Paper written on project work carried out in partial fulfilment of BSc.Eng (Mining Engineering) degreeThe optimization of the cycle time to increase productivity at Ruashi Mining was an on-site project investigation conducted from December 2017 to January 2018. The main objective of the investigation was to determine the actual cycle time components. These comprise the queuing time, loading time, hauling time, and dumping time of ADTs (articulated dump trucks). Data was also collected on two hydraulic shovels to identify where these could be optimized. The actual cycle time obtained was compared to the theoretical cycle time to ascertain the constraints, which affect productivity. By applying Systems Thinking to the cycle time, man-made constraints of the actual cycle time were identified and recommendations to mitigate them suggested to optimize the cycle time. However, rainfall is a natural constraint that adversely affects the actual cycle time, and which cannot be mitigated.In addition, both the theoretical and actual cycle time were analysed, as well as the theoretical and actual productivity for the year 2017. Based on the findings, conclusions and recommendations were made to optimize the cycle time. IntroductionThe aim of the project was to increase Ruashi Mining’s productivity by 39%, from about 7.537 Mt of broken material mined to 12..367 Mt targeted in 2017.BackgroundRuashi Mining is a copper (main commodity), cobalt (by-product), and acid producer located in the Democratic Republic of Congo (DRC), 10 km from the city of Lubumbashi. Figure 1 shows the location of the Ruashi Mining open pit.Ruashi Mining started production in 1911 and in 2005 the mine was registered as a DRC company owned by Metorex Group Limited. In November 2013, the Chinese company Jinchua Group International Resources Co. Ltd. bought a majority stake in the business. Ruashi Mining currently produces 38 000 t of copper and 4400 t of cobalt per annum. The company has contracted NB Mining (a contract mining company) to transport its ore. To optimize the productivity of the mine, considering ore flow delivery at Ruashi Mining, the cycle time is the indicator used in this project. The cycle time components were recorded on site using a stopwatch."

Jul 1, 2019

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By S. Pule, Z. Ndabezimbi, A. Hefer, E. Cupido

This article outlines various projects implemented at Rand Refinery to reduce effluent generation and freshwater consumption. The refinery generates about 2800 m³ of effluent annually and has initiated projects such as granulation water recycle and silver leach optimisation to address these issues. The granulation water recycle project has successfully reduced effluent volumes, while the silver leach optimisation has further decreased effluent by implementing stoichiometric addition of HCl and NaClO3. The vibratory shear enhanced processing (VSEP) trial showed promising results for gold recovery from wastewater, though further trials are recommended. The water savings of the effluent reduction projects are monitored by measuring the amount of effluent pumped to service yard effluent storage facilities with the use of flow meters connected on SCADA. Since the effluent reduction initiative of granulation effluent recycle in FY23, the effluent reduced to 2676 m³. In FY24, the stoichiometric addition of HCl and NaClO3 was implemented in the silver leach process, further reducing the effluent to 2083 m³.

Mar 5, 2025

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004