Search Documents

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

By H. Möller, M. Tshibalanganda, C. Taute, A. du Plessis, M. Leary

Additive manufacturing can be used to produce complex and custom geometries, consolidating different parts into one, which in turn reduces the required number of assemblies and allows distributed manufacturing with short lead times. Defects, such as porosity and surface roughness, associated with parts manufactured by laser powder bed fusion, can severely limit industrial application. The effect these defects have on corrosion and hence long-term structural integrity must also be taken into consideration. The aim of this paper is to report on the characterization of porosity in samples produced by laser powder bed fusion, with the differences in porosity induced by changes in the process parameters. The alloy used in this investigation is AlSi10Mg, which is widely used in the aerospace and automotive industries. The sample characteristics, obtained by X-ray tomography, are reported. The design and production of additively manufactured parts can be improved when these defects are better understood.

Apr 1, 2021

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By Ernst-Ulrich Reuther, Alexander Donmen

Mine ventilation in the German coal mining industry is concerned mainly with problems of thermal environment arising from greater depths and with increasing emission of methane gas. The development of computer techniques over the past ten years for solving these and ancillary problems is reviewed. The emphasis from a planning and control point of view falls mainly on ventilation network calculations, temperature predictions and advance estimates of methane emission.

Jan 1, 2014

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By B. Aydin, A. S. Aloglu, S. Kahraman, E. Saygin

"The coal strength parameter is used in operations such as the selection and design of mechanical excavators and coal crushing/grinding equipment. However, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason a method for the indirect determination of coal strength from easy tests would be useful. In this study, the predictability of coal strength from the needle penetration test was investigated. This is a very easy and practical test method. Point load and needle penetration index (NPI) tests were carried out on coal specimens from Çayirhan coalfield in Turkey. The point load indexes were converted to the uniaxial compressive strength (UCS) values by using the general conversion factor. The UCS and NPI values were evaluated using regression analysis. A strong linear relationship was found between the two parameters. The conversion factor for the UCS-NPI ratio is 0.35 for the tested coal samples. It is concluded that the UCS of coal can be predicted from the NPI.IntroductionKnowledge of coal strength is important for the selection and design of mechanical excavators and coal crushing and grinding equipment. Uniaxial compressive strength of coal is used in designing pillar dimensions in room and pillar mining. Coals always contain bedding planes and cleats; they are also brittle and fragile. Therefore, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason, a method for the estimation of coal strength from easy tests would be useful.The needle penetration test is a nondestructive index test that is applicable both in the field and the laboratory and does not require any special sample preparation. The test has been used for the estimation of physical and mechanical properties of weak or soft rocks (Okada et al., 1985; Yamaguchi et al., 1997; Takahashi, Noto, and Yokokawa, 1988; Uchida et al., 2004; Aydan et al., 2006; Aydan, Watanabe, and Tokashiki, 2008; Aydan, 2012; Erguler and Ulusay, 2007; Park, Obara, and Kan, 2011; Ulusay and Erguler, 2012; Aydan and Ulusay, 2013; Aydan. Sato, and Yagi, 2014). This study investigates the predictability of coal strength from the needle penetration test."

Jan 1, 2017

By S. Banisi, S. M. Mousavi, S. D. Tafvizi, Gh. A. Parsapour, M. Mahmoudi

Generally, regrind circuits are used to increase the degree of liberation of value minerals which are fed to flotation circuits. At the regrind circuit of the Sarcheshmeh copper complex, four ball mills are in closed circuit with their hydrocyclone clusters. In the initial design of the plant, feed and underflow percent solids, and pressure drop of the hydrocyclones were 39% and 65%, and 15psi, respectively. Over the years, due to a reduction in the feed grade from 1.17% to 0.67% and changes in the operational conditions, the feed rate to each hydrocyclone cluster has decreased from 401 to 70t/h and consequently the pressure drop, feed and underflow percent solids have reduced to 4psi, 17% and 25%, respectively. The main objective of this research was to audit the feed solids concentration and pressure drop of the hydrocyclones and make the necessary modifications based on the Plitt’s model. The results of sampling showed that water recovery to underflow was 59% which was higher than normal values. By reducing the number of operating regrind mills from 4 to 2, the feed rate to each mill increased. After this modification and taking necessary measures in the plant to implement the new operating approach, the pressure drop, feed and underflow percent solids increased to 18psi, 28% and 58%, respectively. The water recovery of the hydrocyclones underflow decreased from 59% to 12%. These changes in addition to increasing the circuit efficiency saved 1000 kWh energy and decreased ball consumption by 925 ton/year because of reduction in the number of operating ball mills. Keywords: Regrind mills, flotation, audit, troubleshooting

Jan 1, 2020

By K. Premlall, R. M. Dire, H. Bissett, D. Delport

Tungsten carbide is a fine grey powder. It can be formed into shapes by compacting with the addition of a binder. Spherical particles are generally preferred in additive manufacturing as they pack together more efficiently than non-spherical particles, promoting a uniform powder bed density, better flowability, and elimination of internal cavities and fractures, resulting in a better quality of final product. The particle shape of powders can be transformed into spherical through the process of spheroidization. However, due to its high melting point, tungsten carbide could be difficult to spheroidize. Tungsten carbide was spheroidized using an inductively coupled radio frequency plasma at various plate powers between 9 and 15 kW. The influence of additional H2 in the sheath gas on the chemical composition of the tungsten carbide product was also investigated by means of XRD, which indicated that WC is converted to W2C at higher H2 concentrations. Optical analysis of SEM micrographs indicated that the spheroidization ratio increased with increased plasma energy.

Apr 1, 2021

By M. Dworzanowski

The difference in the magnetic properties of minerals is the basis for magnetic separation. All minerals can be generally classified as ferromagnetic (strongly magnetic), paramagnetic (weakly magnetic) or diamagnetic (non-magnetic). Magnetic separation can be conducted dry or wet. The majority of the applications of wet magnetic separation in the mining industry are based on the wet drum magnetic separator. The wet drum magnetic separator has been in use for over 50 years and its design is based on a rotating drum installed inside a tank. Inside the drum are stationary, permanent magnets arranged in an arc to provide the magnetic field. These magnets can be of the ceramic ferrite type providing a low intensity magnetic field or of the rare earth type providing a high intensity magnetic field.

Jan 1, 2010

By L. E. Salinas-Farran, S. J. Neethling

Key variables in heap leaching include permeability, mechanical stability and mass transport. All of these properties can be manipulated by agglomerating and curing the ore before stacking it into heaps. The chemical and structural evolution of the agglomerates during curing is key to improving agglomerate properties and, ultimately, heap performance. It is possible to image the internal structure of agglomerates using SEM/EDX (e.g. QEMSCAN or MLA), although these methods are destructive and do not represent the 3D structure of the agglomerates. A non-destructive alternative is to image the agglomerates using X-ray Microtomography (XMT). Not only does this provide 3D information, it also allows the same samples to be repeatedly scanned, allowing the time evolution of the agglomerate structure and chemical composition to be tracked. In this paper we compared the behaviour of ores agglomerated using a combination of sulphuric acid and ferric sulphate with ones in which chloride ions are added to the recipe, since chloride leaching is gaining in popularity as a chemical alternative to bioleaching for sulphide ores. We tracked the curing process beyond the typical time scales to see the impact that this has on both the agglomerate structure and the subsequent leaching behaviour. Keywords: Heap leaching, curing extent impact, leaching kinetics, ferric-chloride leaching

Jan 1, 2020

A. H. Mokken: I am pleased to have been given this opportunity to make a contribution to Dr Muller's paper tonight. The reason for this is that, at one stage in our careers, we were associates in the same undertaking. Dr Muller, then fresh from University, with a degree in pure science, had just stepped onto the first rung of the ladder, which, it was then thought, would lead him to a career in gold extractive metallurgy. However, endowed with an enquiring mind and conscious of a lack of fundamental training in general metallurgy and engineering, he felt a need for further academic study. To meet this need and, more importantly, to meet the necessary finances, he found his opportunity in steel. Armed with a bursary, he bade farewell to gold and proceeded overseas, to the University of Sheffield, to train as a steel metallurgist. The outcome of these academic efforts, which were followed by assignments in the steel industry and a further period at Sheffield, is the man we have listened to tonight-a highly qualified metallurgist who has displayed a sound knowledge of his subject. In choosing Sheffield, Dr Muller became associated with a steelmaking centre of world renown, a centre usually credited with the first systematic production of alloy steels, as far back as the 18th century. Since that time, great advances have been made in the production of alloy steels and this is especially so in the last decade or two, when major developments in civil, mechanical, electrical, aeronautical and nuclear engineering have been made possible by the development of steels with improved properties. In spite of spectacular advances in the technology of non-ferrous alloys, plastics and other materials of construction, steel has maintained its role as a pre-eminent material for engineering use. With the gradual accumulation of data on the properties of steels, and the use of thin film electron microscopy, to study the behaviour and characteristics of such phenomena as dislocations in metals and other microstructural features, the physical metallurgist appears to be approaching the stage of an exact understanding of such phenomena as strength, ductility and brittleness-a knowledge which could lead to close control of such properties and, therefore, to the attainment of the highest goals. An interesting example, illustrating the use of fundamental principles, based on physico-metallurgical research, is the development of the maraging steels developed by Bieber at the International Nickel Company. These steels have met the extreme technological requirements of the space age by providing the material for the cases of large rockets in which qualities, such as high tensile strength, toughness, workability and weldability are most important. Attractive as they might appear to be in considerations of savings of weight, cost of erection, transport of materials and foundations, the use of high strength steels has been accompanied by special problems such as brittle fracture, hydrogen embrittlement, notch-toughness and fatigue. It has been found that high strength steels, which performed acceptably in conventional tension tests, were found to undergo failure, in a brittle manner, in service. Hydrogen embrittlement has caused spectacular failures at a fraction of the normal ultimate tensile strength, and a lack of correlation between fatigue and tensile strengths has diminished the advantages to be obtained from the use of high strength steel in some applications. A new approach to the selection of materials for engineering design has resulted from a consideration of these phenomena in which strength, as such, is no longer as significant as it was previously. Parallel with the development of high strength steel has been the need for suitable techniques for joining component parts and here welding has played an

Dr T. F. Muller (Honorary President): "Mr President, gentlemen. May I congratulate the Institute on its 75th birthday, and your President on his comprehensive review of the Institute's 75 years. It is an interesting commentary on the affairs of the Institute that your President should refer to a speech made by a founder member 25 years ago on the occasion of your 50th Anniversary and then say there is no need to repeat what was given there, but that he would confine his remarks to bringing the Institute's history up to date. To me this suggests a remarkable continuity of thought and ideals-a welcome island of stability in an ever-changing world. One can somehow picture another future President, perhaps one of the younger and tougher members here today, doing the same thing in 25 years when you celebrate your centenary-and again someone doing the same in the year 2094 when your Institute is 200 years old! I hope they will recognise their debt to the early pioneers of the Institute gathered here today. In any event, this review of the fine achievements of the past 75 years is certain of an honoured place in the annals of the society. Here is a record of the onward march of technology in South Africa and a tribute to a long line of mining engineers, of chemists, metallurgists and geologists who made a greater contribution to the well-being and the prosperity of South Africans than South Africans generally are aware. Your Institute started off as a 'gold and cyanide club', peopled largely by chemists and metallurgists who made a signal contribution to the industry from the earliest times. Despite the addition to their ranks of ever-growing numbers of mining engineers, the metallurgist members have continued to make notable contributions. One recalls, for example, the manner in which they rose to the occasion to resolve the problems associated with the establishment of the uranium industry in this country. The creation of a major industry based on the existence of low grade uranium ores in the conglomerate reefs of our low grade goldfields is a classic example of the manner in which a new large industry can be rapidly created through the combined endeavours of all concerned. I noted with pleasure your remark, Mr President, that members of the Institute would like to keep up to date with recent progress in nuclear fuel matters and that members should be given the opportunity to study developments in their journal. I am sure that the National Institute of Metallurgy which conducts fuel research on behalf of the Atomic Energy Board and of the Uranium industry, and NUFCOR, which co-ordinates the uranium research programme, would be glad to co-operate if invited by the Institute to make periodical contributions to its journal. You have referred to the building up of our research organization and its dynamic approach to mining problems. I understand that the expenditure of the mineral industries on research exceeds one-third of the entire research expenditure of the private sector. South Africa is in the forefront of mining development and the focus of world attention is on the achievements of our scientists and mining engineers. We can look forward to continued advances in mining technology based on their vision and expertise. I share your disappointment, Mr President, that the Base Metals Division has ceased to exist; and that there is a resultant dearth of papers offered to the Institute on these important sections of mining and metallurgy. We are seeing some remarkable developments in the mining and beneficiation of base minerals, and it is in this area that I see the greatest potential for future expansion. If we can grasp the opportunities

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.

The industrial relations handbook, by A. Pons. Juta (P.O. Box 14373, Kenwyn 7790). 1989. "'"250 pp. Looseleaf binder. R180 + GST. Industrial laser materials processing. World Business Publications Ltd (4th Floor, Britannia House, 960 High Road, London N12 9RY, England). 1989. 180 pp. £310. Mining 1990. Longmans, Financial Times International Year Books, 1989. 592 pp. £90.00. Innovations in materials processing using aqueous, co/oid and surface chemistry, by F.M. Doyle, S. Raghavan, P. Somasundaran, and G.W. Waren (eds.). 300 pp. $125. Light metals 1989, by P.G. Camp bel (ed.). No. of pp. not available. $150. Process control and automation in extractive metalurgy, by R. Partelpoeg and D.C. Himmesoete. 225 $98. Process mineralogy VIl, by D.J. Carson and A.H. Vassiliou (eds.). 4oopp. $150. Super plasticity and super plastic forming, by C.H. Hamilton and N.E. Paton (eds.). 700 pp. $140. Supera/oys 1988, by S. Reichman, D. Duhl, G. Maurer, S. Antolovich, and C. Lund (eds.). 880pp. $99. Surface modification technologies, by T.S. Sudarshan and D.G. Bhat (eds.). 305 pp. $49. World survey of nonferous smelters, by J .C. Taylor and H.R. Traulsen (eds.). 365 pp. $90. Second Parsons International Turbine Conference. London, The Institute of Metals, 1989.270pp. £40. Mineral processing in the United Kingdom. London, Institution of Mining and Metalurgy, 1989. £25. Today's technology for the mining and metalurgical industries. London, Institution of Mining and Metalurgy, 1989. 623 pp. £60. 1989/1990 E&MJ international directory of mining. Chicago, Mining Information Services (P .0. Box 6500, Chicago, IL 60680, USA). 620 pp. US$95. Advances in project scheduling, edited by R. Stowinski and J. Weglarz. Amsterdam, Elsevier, 1989. 540 pp. Dfl. 270. Proceedings of the 3rd International Conference on Molten Slags and Fluxes. London, Institute of Metals, 1989. 335 pp. £38. Brochure on industrial screens. Obtainable from Philippe Lavernhe, Johnson Filtration Systems S.A., Z.I. Availes-en-Chatelerault, 86538 Naintre, France. 16 pp. Free. Numerical techniques, edited by P. Spiling. London, The Institute of Metals, 1989. 226 pp. £25. Phase diagrams of ternary iron aloys, Part 2, by V. Raghavan. New Delhi, Indian Institute of Metals, 1988. 360 pp. £95 (from the Institute of Metals, London). cas publications These publications are available from the Centre for Resource Studies, Queen's University, Kingston, Ontario K7L 3N6, Canada. Economic aspects of gold exploration: How much is too much, by B.W. Mackenzie and M. Dogget. 30 pp. $10.00. Mineral exploration and mine development potential in Ontario: Economic guidelines for government policy, by B.W. Mackenzie, M. Bilodeau, and M. Dogget. 180 pp. $25.00. Economic potential of base metal and gold mining in Newfoundland: Assessing the impact of regional developmentpolicy options, by B.W. Mackenzie, M. Bilodeau, and M. Dogget. 188 pp. $25.00. Publications of the AusIMM The folowing publications are available from The Australasian Institute of Mining and Metalurgy, P. O. Box 122, Parkvile, Vic 3052, Australia. Prepayment is required with al orders. The AusIMM 1989 Annual Conference 1989. $A 50. Mineral fuel alternatives and the greenhouse efect. July 1989. A$ 35. NQ gold '89. Apr. 1989. $A 50. Second Large Open Pit Mining Conference. Apr. 1989. $A 50. Explo '88. Nov. 1988. $A45. Mineral deposits of New Zealand, edited by Dr D. Kear. Monograph 13. 244 pp. $A 60. Field geologists' manual, compiled by D.A. Berkman. 3rd edition. 1989. : 350pp. $A45. The rocks speak. Essays in geology-some personal responses of a wiling listener, by Haddon F. King. 300pp. $A45.

Jan 1, 1990

1. Book reviews Tungsten: 1982. London, Mining Journal Books Ltd, 1982. 179 pp. Reviewer: G.A. Brown The geology of industrial minerals in Canada, edited by G.R. Guillet and Wendy Martin. Canadian Institute of Mining and Metallurgy, special volume 29. Reviewer: R.W.O. Kersten Foam flotation - theory and applications, by Ann N. Clarke and David J. Wilson. New York, Marcel Dekker, 1984. 418 pp. Reviewer: B.K. Loveday Industrial and financial indicators of the steel industry, by Patrick Genevaz. Paris, La Chambre des Cartes, 1982. 2 vols. Vol I: Analysis and conclusions, FF3500. Vol. 11: Tables, FF4000. Reviewer: R.J. Dippenaar An encyclopaedia of metallurgy and materials, by C.R. Tottle. Plymouth, Macdonald and Evans and The Metals Society, 1984. 481 pp. RI44,50. Reviewer: P. T. Wedepohl The role of crack growth in metal fatigue, by LP. Pook. London, The Metals Society. Reviewer: C.A. Boothroyd Hydraulic coalmining - new technology and its geological and industrial significance, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 33 pp. Hydraulic coalmining - hydromining update: potential impact on coal deposits and coal mining industry, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 130 pp. Victoria's brown coal. A huge fortune in chancery, edited by J .T. Woodcock. The Australasian Institute of Mining and Metallurgy, 1984. 204 pp. Reviewer: J.J. Versluis 2. Canadian publications The following reviews of the activity and developments during 1982 in respect to the chief minerals produced or consumed in Canada are now available. Zirconium. An important mineral commodity. Mineral Policy Sector, Mineral Bulletin MR 202, $6.60. Canadian minerals yearbook 1982. Mineral Policy Sector, Mineral Report 32, $40.75. Canadian reserves of copper, nickel lead, zinc, molybdenum, silver and gold as of January 1, 1983, by W.H. Laughin. $4.20. Mineral Policy Sector, Mineral Bulletin MR 201. Sulphur market profile, by B.W. Boyd. Mineral Policy Sector, MRI 84/5. 3. Mintek publications Report M123 The use of of activated charcoal in a NIMCIX column for the recovery of gold from cyanide solutions. Report M150 Energy transfer in the hearths of submerged-arc furnaces. Report M151 A preliminary investigation of the initiation of pitting corrosion in austenitic stainless steels and nickel-based alloys. Report M154 The reduction of Winterveld chrome spinel at 1300°C under an argon atmosphere in the presence of carbon. Report M165 The development of an improved on-line gold analyser. Report MI67 three nebulizers for use with an inductively coupled plasma spectrometer. 4. New publications Mineral Industry Consultants Association (as at 31st March, 1984). Parkville (Australia), The Australasian Institute of Mining and Metallurgy, 1984. 112 pp. Philosophical and procedural guidelines for the planning professions. Johannesburg, the Environmental Planning Professions Interdisciplinary Committee (EPPIC, P.O. Box 61019, Marshalltown 2107), R2.50. Directiona//y solidified materials for high temperature service, by M. McLean. London, the Metals Society, 1983. 337 pp. Tin and its uses no. 142. Greenford (England), International Tin Research Institute, 1984. Metals engineering International Symposia & Exhibitions Ltd - a subsidiary of Industrial Newspapers PLC - are pleased to announce that they will be organizing a mammoth engineering event, entitled Metals Engineering 86, comprising five important exhibitions in 1986:. Agglomeration A major symposium on agglomeration is being organized in Toronto for the 2nd to 5th of June, 1985. Speakers from around the world (Canada, U.S.A., Brazil, Australia, Japan, West Germany, Italy, India, China, Switzerland, Poland, Yugoslavia, and France) will address delegates on various aspects of agglomeration relative to iron ore, coal, coke, and fuels. Plenary theme papers will also be presented by speakers from Japan, the U.K., and the Netherlands.

Jan 1, 1985

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018